Rinnai RHFE-309FT Specification sheet

Please note:
Flue System Installation Instructions
enclosed with Flue Terminal packaged
separately.
This appliance shall be installed in accordance with:
• Manufacturer’s Installation Instructions
• Local Gas Fitting Regulations
• Municipal Building Codes
• AS 5601 Gas Installations, AS/NZS 3000 Wiring Rules
• Any other relevant Statutory Regulations
This appliance must be installed, serviced and removed by an authorised person.
All Rinnai gas products
are A.G.A. certified.
Distributed and serviced in Australia under a Quality
System certified as complying with ISO 9001 by
SAI Global
Energysaver®Space Heaters
Models: RHFE-309FT & RHFE-559FT
Operation and Installation Manual
Models:
RHFE-309FT
RHFE-559FT

Rinnai Australia i Energysaver® - Operation & Installation Manual
INSTALLATION REQUIREMENTS
This heater must be installed by an authorised person. The installation must conform to local regulations.
The installation must also comply with the instructions supplied by Rinnai.
Service and removal must be carried out by an authorised person.
The Rinnai Energysaver®Range have been certified by the Australian Gas Association.
The AGA Certification Number is shown on the appliance dataplate.
No parts or functions should be modified or permanently removed from the heater.
Please keep these instructions in a safe place for future reference.
Check you have the following:
1 x Rinnai Space Heater - RHFE-309FT or RHFE-559FT
1 x Rear Cover set, comprising of left, right and top cover panels
1 x Bolt pack containing;
• Stainless steel sheath clamp
• 2 x securing brackets
• 2 x 8g x 30 mm stainless steel securing bracket screws
• 2 x plastic inlet hose clamps
• 1 x 150 mm long cable tie
• 1 x HD stainless steel flue clamp
• 2 x 6g x 10 mm button head screws
• 4 x 6g x 8 mm pan head screws.
CERTIFICATION
CARTON CONTENTS

Rinnai Australia ii Energysaver® - Operation & Installation Manual
INSTALLATION REQUIREMENTS .........................................................................................i
CERTIFICATION ......................................................................................................................i
CARTON CONTENTS .............................................................................................................i
ABOUT YOUR ENERGYSAVER® ..........................................................................................1
Control Panel Layout .........................................................................................................1
SAFETY ..................................................................................................................................2
Important ...........................................................................................................................2
FEATURES .............................................................................................................................7
CUSTOMER INFORMATION - OPERATION .........................................................................8
To turn the unit ‘ON’ ..........................................................................................................8
To turn the unit ‘OFF’ .......................................................................................................8
Room Temperature Adjustment .......................................................................................8
Economy Mode ................................................................................................................9
Child Lock / Function Lock ...............................................................................................9
Fan Operation ...................................................................................................................9
SETTING THE CLOCK .........................................................................................................10
Setting the Clock/Timers .................................................................................................10
Day light saving and time adjustment .............................................................................10
Setting the ON / OFF Timers ..........................................................................................10
OPERATING THE TIMERS ..................................................................................................11
Operating the Timers ......................................................................................................11
Set and Forget Operation ................................................................................................11
Override ..........................................................................................................................11
OTHER OPERATING INFORMATION .................................................................................12
Pre-Heat ..........................................................................................................................12
Humidifier Tray ................................................................................................................12
Vertical Louvre Adjustment .............................................................................................12
Outside Flue Terminal .....................................................................................................12
CARE OF YOUR ENERGYSAVER® .....................................................................................13
Cleaning ..........................................................................................................................13
Fan Filter .........................................................................................................................13
SAFETY DEVICES ...............................................................................................................14
Overheat Switch: .............................................................................................................14
Fusible Links: ..................................................................................................................14
Flame Failure Device: .....................................................................................................14
Electrical Fuse: ................................................................................................................ 14
Power Failure: .................................................................................................................14
SERVICE ...............................................................................................................................14
INSTALLATION MANUAL - TABLE OF CONTENTS .........................................................16
CONTACT INFORMATION .................................................................................................. 29
TABLE OF CONTENTS

Rinnai Australia 1 Energysaver® - Operation & Installation Manual
Control Panel Layout - RHFE-309FT / RHFE-559FT
Main switch for turning 'ON / OFF'.
'ON' / 'OFF' BUTTON
1
Selects clock and/or Timers for
adjusting or programming.
SET TIMES BUTTON
2
POWER ON /COMBUSTION
INDICATOR
9
Indicates that clock or dual timer
programme is being set.
CLOCK ADJUSTMENT &
TIMER INDICATORS
Indicates that the filter needs cleaning.
FILTER INDICATOR 10
Increases or decreases the temperature
setting as well as changing hours or
minutes
Indicates that the appliance is turned ON
and whether the burner is alight.
TIME / TEMP ADJUSTMENT
BUTTON
34
Temporarily changes operation from
ON to OFF or OFF to ON, until next
programmed setting is reached.
OVERRIDE BUTTON
Selects operating mode for
Timers 1 & 2 .
ON TIMER BUTTON
5
Locks all controls when pressed.
(EXCEPT OFF)
CHILD LOCK BUTTON
78
6
Selects energy saving function
ECONOMY BUTTON
Indicates that the override function
is activated.
OVERRIDE INDICATOR
12
Shows either the time of day,
temperatures, or coded error message
TIME / TEMP DISPLAY
11
Indicates Child lock is activated.
CHILD LOCK
INDICATOR
15
123
75
8
15
9
13 12
14 11 10
64
Indicates that Timer 1 or Timer 2 has
been selected to operate.
TIMER INDICATOR
13 14 ECONOMY INDICATOR
Indicates that the Economy mode is
in operation.
ABOUT YOUR ENERGYSAVER®

Rinnai Australia 2 Energysaver® - Operation & Installation Manual
Important
Unpack the heater and check for damage. DO NOT INSTALL DAMAGED HEATER. If the heater is
damaged, contact your supplier for advice. Before installing the heater, check the label for the correct
gas type (refer rating plate, right hand side panel).
Refer to local gas authority for confirmation of the gas type if you are in doubt.
Important Points
1. The appliance must be installed in accordance with the local gas and electrical authority regulations.
2. For information on gas consumption, refer technical specifications on page 17 and check with the
data plate on the appliance.
3. This appliance must not be installed where curtains or other combustible materials could come into
contact with it. In some cases curtains may need restraining.
4. Heater must not be located below a power socket-outlet.
5. The local gas and electrical authorities will be able to advise on local regulations.
6. Only the approved flue components specified by Rinnai must be used.
1. The appliance must be installed in accordance with the local gas and electrical
authority regulations.
2. DO NOT connect to an LPG Gas cylinder indoors.
3. A dedicated 240 V earthed 10 Amp power point must be used with this
appliance.
4. Heat emanating from the front of this
appliance may over time affect the
appearance of some materials used for
flooring such as carpet, vinyl, cork or
timber. This effect may be amplified if the
air in the room contains cooking vapours
or cigarette smoke. To avoid this
possibility, it is recommended that a mat is
placed in front of the appliance, extending
at least 750 mm in front of the air outlet.
5. The appliance is not intended for use by young children or infirm persons
without supervision.
6. This appliance is not intended for use by persons (including children) with
reduced physical, sensor or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instructions
concerning use of this appliance by a person responsible for their safety.
7. Young children should be supervised to ensure they do not play with the
appliance.
8. If the supply cord is damaged or require replacing, it must be replaced by the
manufacturer or the manufacturer's agent or similarly qualified person in order
to avoid a hazard.
9. DO NOT modify this appliance. Modifying it in any way or form, from original
specifications may create a dangerous situation and will void your warranty.
WARNING
AT LEAST
750mm
SAFETY

Rinnai Australia 3 Energysaver® - Operation & Installation Manual
DO NOT allow children to post articles in the
louvres.
The appliance is not intended for use by
young children or infirm persons without
supervision.
Young children should be supervised to
ensure they DO NOT play with the appliance.
DO NOT allow children or elderly persons to
sleep in the warm air discharge from the
heater.
DO NOT cover or place articles on or against
this heater.
Turn ‘OFF’ heater after use.
SAFETY

Rinnai Australia 4 Energysaver® - Operation & Installation Manual
Keep away from flammable materials.
Combustible materials must not be placed
where the heater could ignite them.
DO NOT place articles on or against this
appliance.
DO NOT use or store flammable materials
near this appliance.
DO NOT spray aerosols in the vicinity of this
appliance while it is in operation.
Most aerosols contain butane gas which can
be a fire hazard if used near this heater when
it is in use.
DO NOT sit on this heater.
DO NOT place articles in front of the louvres.
DO NOT unplug the heater while it is in
operation or while the fans are still cycling.
DO NOT turn the heater ‘OFF’ by unplugging
it from the wall.
SAFETY

Rinnai Australia 5 Energysaver® - Operation & Installation Manual
DO NOT place containers of liquid on top of
the heater. Water spillage can cause
extensive damage to the appliance and may
result in electric shock.
A dedicated 240V earthed 10 Amp power
point must be used with this appliance.
DO NOT use power boards or double
adaptors to operate this appliance.
Heater must not be located below a power
socket-outlet.
This appliance must not be built-in.
The clearances shown must be maintained.
Access panel and Humidifier tray have to be
fitted while the heater is in use.
Rinnai recommend you fill the tray to the water
level indicator as marked. Take care not to
overfill.
Heat emanating from the front of this
appliance may over time affect the
appearance of some materials used for
flooring such as carpet, vinyl, cork or timber.
This effect may be amplified if the air in the
room contains cooking vapours or cigarette
smoke. To avoid this possibility, it is
recommended that a mat be placed in front of
the appliance, extending at least 750 mm in
front of the air outlet.
250mm
1000 mm
50 mm50mm
TOP
FRONT
LEFT SIDE RIGHT SIDE
Pull Humidifier Tray
Gently Remove
Access Panel
Pull
AT LEAST
750mm
SAFETY

Rinnai Australia 6 Energysaver® - Operation & Installation Manual
During peak operating periods the filters
should be cleaned weekly, however if the
“FILTER” warning indicator flashes in the
control panel display, turn off the appliance
immediately and clean filters before further
use.
When the heater is operated for the first time
or after long periods of non use a slight odour
may be emitted, this is normal.
However if odours persist switch ‘OFF’ the
appliance and contact Rinnai.
Keep flammable materials, trees shrubs etc.
away from the flue terminal.
Snow Areas - in areas subject to heavy
snowfall, keep snow clear of flue terminal at all
times.
SAFETY

Rinnai Australia 7 Energysaver® - Operation & Installation Manual
ROOM SEALED Air for combustion is taken from the outside and the flue
product are exhausted to the outside. This means heater
operation has no effect on the composition and quality of air in
the room.
PUSH BUTTON IGNITION Only one touch of the ‘ON’/’OFF’ button is required to operate
the heater.
FUNCTION / CHILD LOCK Prevents children from altering heater settings whilst running,
or from activating the heater when turned ‘OFF’.
MEMORY The micro-computer records selected preset temperatures, the
times programmed into Timers as well as operating the
Economy/Auto-Off and Pre-heat modes, to maintain comfort
levels.
7 STEP AUTOMATIC HEAT
CONTROL
Selected temperature is controlled via thermostat. The
optimum corresponding fan speeds are controlled by the
Central Processing Unit.
PRE-HEAT This function will automatically operate the appliance before
the programmed start time of the Timer, in order to heat a room
to the pre-set temperature by the programmed start time.
ECONOMY MODE The Economy (ECON) function is an energy saving features
designed to control the room temperature and prevent
discomfort from over heating.
OVERRIDE FUNCTION This temporarily changes the heater operation from ‘ON’ to
‘OFF’, or vice versa, until the next programmed setting is
reached.
DUAL WEEKDAY / WEEKEND
TIMER
The Dual WEEKDAY/WEEKEND Timer allows you to program
the appliance to come on for two separate periods each day,
one period in the morning and one period in the evening. The
built in Pre-heat Mode brings the room temperature to the
temperature you have selected, by the time programmed into
the Timer.
The Dual Timer feature means that you can "Set and Forget"
your heater. It will turn itself ‘ON’ or to STANDBY at the times
you have programmed until you cancel the Timer program.
FILTER INDICATOR When the fan filters become covered with dust, the filter
indicator will flash. The filters should be vacuumed at regular
intervals to avoid unnecessary strain on the appliance.
HUMIDIFIER TRAY The integral humidifier tray can be filled with water as required
to raise the humidity level in the room for extra comfort.
Tray should not be filled to more than 3/4 full.
FEATURES

Rinnai Australia 8 Energysaver® - Operation & Installation Manual
To turn the unit ‘ON’
Press the ‘ON’/’OFF’ button to operate the heater. The ‘ON’ indicator will glow green. The spark
generator will be heard before the burner ignites and the ‘ON’ indicator glows red, indicating that the
heater is alight.
When the heater warms up, the fan will automatically start.
If the heater does not ignite on initial use, this may be due to air remaining in the gas supply line. The
spark generator will only continue for 15 seconds. After this it will be necessary to press the ‘ON’/
’OFF’ button ‘OFF’, then ‘ON’ again.
If the appliance fails to ignite after 4 attempts, contact Rinnai as a service call may be required.
To turn the unit ‘OFF’
Simply press the ‘ON’/’OFF’ button to switch ‘OFF’ the heater. The ‘ON’ indicator light will go out.
The Fan will continue to operate for several minutes after the burner has gone out in order to cool the
appliance. Do not unplug the appliance while the fan is running.
Room Temperature Adjustment
The room temperature and pre-set temperatures can only be displayed and adjusted when the heater
is running.
Press the “ ” button to increase the temperature setting or “ ” button to decrease the
temperature setting.
The temperatures can be preset to:
a) [L] - Temperature is controlled at set temperature “Low”.
b) [16°C] to [26°C] in 1°C steps - thermostatic control to preset temp selected. Combustion rate
varies as required to maintain the selected temperature.
c) [H] - continuous combustion on ‘High’.
13
7
8
9
1415 11 10
13
6
12
42
You must read and understand these instructions fully before operating the
heater.
WARNING
1
1
9
9
1
1
1
9
3
3
3
Room temperature on the TIME/TEMP Display may vary slightly from the
actual room temperature.
If the heater does not ignite then the pre-set temperature may not be set to a
setting which is higher than the room temperature. The ‘ON’ indicator will
change colour from red to green when the heater reaches the pre-set
temperature and stops running.
NOTE
11
9
CUSTOMER INFORMATION - OPERATION

Rinnai Australia 9 Energysaver® - Operation & Installation Manual
Economy Mode
The Economy (ECON) function is an energy saving features designed to control the room temperature
and prevent discomfort from over heating.
• When the room temperature reaches the set temperature, the set temperature decrease at the rate
of 1°C per 30 minutes in two cycles.
• The set temperature on the display does not change.
• Room temperature may not decrease in some cases, this is depending on room style, location of
the appliance and the temperature outside the room.
Child Lock / Function Lock
The Child Lock function will help to prevent accidental operation as well as prevent small children from
altering the controls. To operate the Child Lock simply press the Child Lock button. The function is
activated immediately and the Child Lock indicator will glow.
To Deactivate the Child Lock simply press the Child Lock button for 2 seconds and the Child Lock
indicator will go out. The Child Lock can be deactivated at any time in this way.
During normal operation the Child Lock may be activated and all controls, other than the ‘OFF’ switch,
will be locked. Deactivating the Child Lock releases the controls. If the Child Lock is activated whilst the
heater is turned ‘OFF’, then all functions will be locked. If the heater is turned ‘OFF’ while the Child Lock
is activated, it cannot be turned ‘ON’ again until the Child Lock is deactivated.
Fan Operation
The fan turns ‘ON’ automatically when the heat exchanger warms up and off when it cools down.
This helps to prevent cold draughts and maximises efficiency.
1. The Economy mode can only be operated when the heater is turned ‘ON’, but remains in the
system memory until deactivated.
Select the Economy mode before selecting timer operation.
2. Press the Economy button to start the Economy function. The Economy indicator will glow.
3. Press the Economy button once more to switch ‘OFF’ the economy function.
6
7
7
15
7
15
6
14
6
CUSTOMER INFORMATION - OPERATION

Rinnai Australia 10 Energysaver® - Operation & Installation Manual
Setting the Clock/Timers
When the appliance is first plugged in or after a power failure, the Digital Display with show
--:--
As an example, let’s set the clock to 10:35 am;
1. Press the Set Times button once, the Clock/Timer indicator will flash.
2. Press and hold the “ ” button; the minutes will begin to change first then the time will change
by whole hours.
3. Release the button when AM 10:00 shows on the Digital Display . Confirm that you have
selected AM, a small indicator on the left hand side of the Digital Display indicates the AM setting.
4. Press and hold the “ ” button again, release the button when AM 10:35 shows. If you go past
AM 10:35, then the “ ” button can be used to change the time settings in reverse.
5. Press the Set Times button five times to lock in and complete setting the time. The Clock and
Timer indicators will go out. A small indicator on the Digital Display will flash to show that the
Clock is operating.
6. The display will dim approximately 10 seconds after the last control.
Day light saving and time adjustment
• Follow steps 1 to 5 to adjust for day light saving and for time adjustment.
Setting the ON / OFF Timers
Example: programming Timer 1 to heat the room by 7:10 am and finish at 9:00 am.
1. Press the Set Timers button twice. The Digital Display will show AM 6:00. The Clock/Timer
indicator will flash.
2. Press the “ ” button until AM 7:00 appears, release the button, then press it again until AM
7:10 appears. (Press the “ ” button if you go past AM 8:00).
3. Press the Set Times button again, the Timer 1 ‘OFF’ indicator will flash. Press the “ ” button
until AM 9:00 appears.
4. Press the Set Times button three times to lock in the program time. The Digital Display will
show the current time. A small indicator on the Digital Display will flash to shown that the
display has returned to the clock.
5. Timer 2 is programmed in the same way. Remember to ensure that the Timer indicator is
flashing when you programming in the desired setting.
123
9
11 10
11
2
10
3
11
3
3
2
11
Before programming the Timers you must ensure that the clock has been set
to the correct time.
NOTE
2
11
10
3
3
2
2
11
11
10
This procedure is for setting the ‘ON’/ ‘OFF’ times for Timers. To program the
time periods refer page 11.
If during setting no buttons are pressed for 1 minute the setting sequence will
automatically cancel and the display will revert to normal display.
NOTE
SETTING THE CLOCK

Rinnai Australia 11 Energysaver® - Operation & Installation Manual
Operating the Timers
The timers can be programmed to operate for any two time periods in any 24 hours. Before operating
the Timer(s), the clock time must be correct and a starting time and finishing time for the Timer(s) must
be programmed. The two Timers operate in the same way. This heater does not commence operation
at the programmed starting time. It will attempt to heat a room by the programmed starting time. Refer
to “Pre-Heat” on page 12, for further explanation.
To select the Timer(s) to commence heating:
• Set Times button and check the time shown on the Digital Display is correct. Press the Set
times button to finish flashing on the timer indicator(s).
• Check the ON and OFF times, for both Timers if necessary, (refer to ‘setting the ‘ON’/‘OFF’
timers’).
• Press the ON/OFF button to operate the heater without the clock / timer indicator flashing.
The ‘ON’ indicator will glow green.
• Select the desired temperature setting.
Press the Timer 1 and/or Timer 2 button(s). The timer indicator(s) will glow. The heater will now
remain on standby until up to one hour prior to the time programmed into the selected Timer(s) is
reached. Timer indicator also flash during Pre-heat (Combustion). When this time is reached, the Timer
indicator will flash and the heater will operate. The ‘ON’ indicator glows red when the heater
commences operation. Actual start time will depend on temperature selected and current room
temperature. (Refer to Pre-heat section for details).
Set and Forget Operation
Your heater can be operated to alternate between Timers automatically during cold whether by
selecting Timer 1 and Timer 2 button together. Both Timer indicator(s) will glow. The appliance
will remain on standby at intervals between the programmed finishing and starting times of each Timer.
While the heater is operating during programmed intervals the Timer indicator(s) will flash.
Override
This function is intended to be used to manually override the current operation of the heater. For
example; if the heater is in standby mode (i.e. between finishing time and starting time of a Timer) and
the Override button is selected, then the heater will begin to operate and heat the room.
To operate the Override simply press the Override button. The Override indicator will flash.
To manually deactivate the Override simply press the Override button again. The Override
indicator will go out, and the heater will return to standby mode.The heater will continue to operate on
Override until the Override button is pressed again, or one of the Timers takes over the operation of the
appliance. This means that the Override mode will automatically drop out if a programmed starting time
is reached.
The appliance will then return to operating at the times programmed into the Timer(s).
123
9
11 10
5
13 12
4
2
11
2
10
1
10
9
3
5
13
9
5
13
13
If there is a power failure, the system memory will retain the Timer programs,
and the clock will stop at the time the power goes off. The clock will re-start
again when the power comes back on, but the time will be slow by the duration
of the power failure. To set the clock to the correct time after the power has
come back on, simply follow the instructions on “SETTING THE CLOCK” on
page 10.
NOTE
4
4
12
4
12
OPERATING THE TIMERS

Rinnai Australia 12 Energysaver® - Operation & Installation Manual
Pre-Heat
This function operates automatically in
conjunction with the Timers. When a Timer is
selected, the heater may operate anywhere
within an hour prior to the programmed starting
time on the Timer.
This function is called Pre-heat since it ensures
the room reaches the desired temperature by the
time the Timer programs ON time. The room
temperature is sensed one hour before reaching
Timers programmed ON time.
The temperature differential at the time of sensing the room temperature combined with the data from
previous operation governs exactly how long before the programmed ‘ON’ time the micro-computer will
operate the heater and ignite the burner.
Humidifier Tray
Your heater is fitted with an enamelled tray behind the air outlet so that you can humidify the air. To fill
the tray, open the access panel as shown in the diagram and pour water into the tray using the spout
built into the access panel. Do not fill the tray over 3/4 full.
The air will be humidified as it passes over the water in the tray.
Humidifier Tray may become hot!
DO NOT FILL THE HUMIDIFER TRAY WHILST THE HEATER IS IN
OPERATION.
DO NOT fill the humidifier tray for at least 5 minutes after the heater stops
operating.
DO NOT operate the heater without the humidifier tray in place.
If you notice water in the humidifier tray, but have not placed
any there do not be alarmed, this is normal. Due to the high
efficiency of Energysaver®heaters, water in the form of
condensate is accumulated in the flue system which drains
into the humidifier tray.
If the humidifier is in use, it will need filling approximately
about once a day during the heating season.
Vertical Louvre Adjustment
The warm air flow direction may be altered by carefully
inserting a screwdriver or similar tool and gently bending the
vertical louvre(s) either to the left or the right.
NOTE: These louvres are not designed to be adjusted
more than 6 times.
Outside Flue Terminal
On cold days steam may be discharged from the flue terminal. This is normal with high efficiency
appliances such as the Energysaver®range and does not indicate any fault.
CAUTION
Pull Humidifier Tray
Gently Remove
Access Panel
Pull
OTHER OPERATING INFORMATION

Rinnai Australia 13 Energysaver® - Operation & Installation Manual
Cleaning
Your heater requires very little maintenance, but the following information will help you to keep it
looking like new and working efficiently.
• Unplug electrical cord before cleaning.
• All parts of the heater can be cleaned using a soft, damp cloth and a mild detergent.
•DO NOT use solvents or abrasives to clean any parts.
Care for the Humidifier Tray: if the humidifier tray gets dirty, wash in warm soapy water.
How to clean: when heater is cold, remove the lower cover panel and pull out the humidifier tray from
appliance. Ensure there is no water in the tray. If there is water in the tray, Keep the tray level to avoid
spilling then wash in warm soapy water.
Fan Filter
To protect the appliance internals from dust
particles or lint, a filter is situated at the rear of the
heater.
If the filter becomes blocked, the filter indicator
will flash to indicate that it should be cleaned. Clean
the filter weekly during the heating season. Dusty or
clogged filters reduce the air flow through the
appliance reducing heating effectiveness.
• DO NOT remove filter when appliance is
operating.
• If the filter requires cleaning, clean filter whilst
the appliance is not operating.
The ‘ON’ indicator will flash & the display
shows error code 14.
Note: If you do not clean the filter at regular
intervals and the Filter Indicator is allowed
to remain flashing, then the appliance will stop.
You must clean the filter before operating the
heater again.
•DO NOT use the heater with the filter indicator
flashing as this may cause overheating.
•DO NOT wait for the filter indicator to flash
before cleaning filters, how to clean the Fan
Filter: Dust: Use duster or vacuum to remove
dust. Oil: Wash the fan filter with a mild
detergent. Drain off the water and dry the filter.
Ensure to fit the Fan Filter back in the appliance after cleaning.
DO NOT operate appliance without filter in place.
Regularly check the outside flue terminal to make sure it is clear from plant growth and from other
obstructions. Refer “SAFETY” on page 2 for additional requirements.
1
8
9
14
8
9
8
Remove filter by pulling straight
up and out from appliance.
WARNING
CARE OF YOUR ENERGYSAVER®

Rinnai Australia 14 Energysaver® - Operation & Installation Manual
Overheat Switch:
This device automatically shuts the gas supply off if the heater exceeds a predetermined temperature.
This is normally caused by an obstruction in front of the louvres, or a blocked fan filter.
If the overheat switch operates, turn the unit ‘OFF’, remove the obstruction (clean filters) and allow the
unit cool off for 10-15 minutes before re-operating.
Fusible Links:
The fusible link activates under conditions of severe overheating and shuts off the gas supply.
A service call will be required to repair the appliance.
Flame Failure Device:
If the flame goes out during operation this device shuts off gas to the burner. To reset, turn the unit ‘OFF’,
then ‘ON’ again. If this happens repeatedly a service call is required.
Electrical Fuse:
The electrical circuits areprotected by an electric fuse. When thefuse blows, the heater will not operate.
The fuse must be replaced by an authorised person.
Power Failure:
In the event of a power failure or power cut, the gas valves will automatically close. After the power is
re-instated the appliance will automatically re-start. The time of day will need to be reset to the correct
current time (refer “SETTING THE CLOCK” on page 10).
Rinnai Australia has a service and spare parts network in all states. Our service network personnel are
fully trained and equipped to give the best service on your Rinnai appliance. If your appliance needs
servicing, please ring one of the service contact numbers on the back of this booklet.
Rinnai recommends that this appliance is serviced every 2 years.
SAFETY DEVICES
SERVICE

Rinnai Australia 15 Energysaver® - Operation & Installation Manual

Rinnai 16 Energysaver® - Operation & Installation Manual
SPECIFICATIONS ....................................................................................................17
Specification Table ............................................................................................17
DIMENSIONS ...........................................................................................................18
HEATER LOCATION ................................................................................................20
Location..............................................................................................................20
Gas supply ........................................................................................................20
Purging the gas supply ......................................................................................20
Electrical supply ................................................................................................20
FLUE INSTALLATION CONFIGURATIONS ............................................................21
FLUE POSITIONING .................................................................................................22
Flue terminal location ........................................................................................22
HEATER INSTALLATION.........................................................................................23
COMMISSIONING .....................................................................................................24
TROUBLE SHOOTING .............................................................................................25
Trouble Shooting Check List .............................................................................25
ERROR MESSAGES ................................................................................................27
WIRING DIAGRAM ...................................................................................................28
CONTACTS ...............................................................................................................29
INSTALLATION MANUAL - TABLE OF CONTENTS

Rinnai Australia 17 Energysaver® - Operation & Installation Manual
Specification Table
NOTE: For other appliance Specifications refer to appliance data plate.
General
RHFE-309FT RHFE-559FT
Dimensions 695mmH x 257mmD x 465mmW 582mmH x 257mmD x 760mmW
Weight 21 kg 26 kg
Gas Control valve Rinnai
®
Electronic Modulating Gas Control Valve
Burner Fabricated Stainless Steel – Bunsen Burner Type
Gas Inlet thread R1/2 Male (15mm)
Flue System
Fan assisted, twin chamber co-axial flue system, provides air for combustion
to the appliance and allows expulsion of combustion products to
atmosphere. Results in ‘room sealed’ appliance.
Ignition Direct continuous spark electronic ignition – no pilot.
Electrical supply
240V 50Hz with supply lead and 3 pin plug. Replace with Rinnai
®
genuine part.
Standby power
consumption <1W
Convection fan Centrifugal Drum Type Fan Cross Flow Fan
Temperature range 16°C - 26°C x 1°C Increments
The manufacturer reserves the right to change or modify specifications without notice.
SPECIFICATIONS