RiverRidge Ashland 2 Door Wall Cabinet User manual

ASSEMBLY INSTRUCTIONS
Ashland 2 Door Wall Cabinet
ADULT ASSEMBLY REQUIRED
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
WARNING SEE FULL WARNING ON PAGE 2
Young children can be seriously injured or killed if furniture tips over. Don’t use
this item for a TV stand or place heavy objects on top of item. Always use
angle-braces or anchors to secure furniture to the wall.

THIS CABINET WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 50 POUNDS.
DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS. LOADING WITH MORE THAN
25 POUNDS PER SHELF MAY CAUSE DAMAGE TO THE CABINET OR CAUSE SERIOUS
INJURY OR DEATH.

PARTS LIST
NO
QTY
DESCRIPTION
1
1PC
Top Board
2
1PC
Left Side Panel
3
1PC
Right Side Panel
4
1PC
Right Door
5
1PC
Left Door
6
1PC
Rear Cross Bar
7
1PC
Towel Bar
8
1PC
Fixed Shelf
9
1PC
Bottom Board
10
1PC
Lower Back Board
11
1PC
Upper Back Board
12
1PC
Middle Back Board

NO
PARTS
QTY
DESCRIPTION
A
10PCS
Cam Bolt
B
10PCS
Cam Lock
C
16PCS
Wood Dowel
D
4PCS
Metal Hinge
E
1PC
Magnet
F
2PCS
Magnet Plate
G
2PCS
Knob
H
2PCS
Machine Screw (4x20mm)
J
18PCS
Screw (3x10mm)
K
2PCS
Screw (3x14mm)
M
20PCS
Screw (2.5x12mm)
N
2PCS
Screw (4x45mm)
O
2PCS
Plastic Anchor
1PC
Wall Mounting Paper Template
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED

STEP 1
1. Attach magnet plate (F) to left door (5) by inserting 1 screw (J) through hole on magnet
plate (F), then tighten to left door (5).
2. Attach knob (G) to left door (5) by inserting 1 machine screw (H) through hole on left door
(5), then tighten to left door (5).
3. Repeat above steps to assemble magnet plate (F) and knob (G) to right door (4).
4. Screw 4 cam bolts (A) into cam bolt holes on top board (1).
5. Insert 2 wood dowels (C) into wood dowel holes on top board (1).
6. Attach magnet (E) to top board (1) by inserting 2 screws (K) through holes on magnet (E),
then tighten to top board (1).
STEP 2
1. Attach 2 metal hinges (D) to right side panel (3) by inserting 4 screws (J) through holes on
metal hinges (D), then tighten to right side panel (3).
2. Screw 3 cam bolts (A) into cam bolt holes on right side panel (3).
3. Insert 7 wood dowels (C) into wood dowel holes on right side panel (3).
4. Repeat above steps for left side panel (2).

STEP 3
1. Attach rear cross bar (6), fixed shelf (8), bottom board (9) and lower back board (10) to left
side panel (2) by inserting cam bolts and wood dowels into cam lock and wood dowel
holes on rear cross bar (6), fixed shelf (8), bottom board (9) and lower back board (10).
2. Insert 3 cam locks (B) into cam lock holes on bottom board (9) and lower back board
(10), then rotate clockwise to secure cam bolts (A) in place.
STEP 4
1. Insert towel bar (7) into hole on left side panel (2).
2. Attach right side panel (3) to rear cross bar (6), fixed shelf (8), bottom board (9), lower
back board (10) and towel bar (7) by inserting towel bar (7) into hole on right side panel
(3) and inserting cam bolts and wood dowels into cam lock and wood dowel holes.
3. Insert 3 cam locks (B) into cam lock holes on bottom board (9) and lower back board
(10), then rotate clockwise to secure cam bolts in place.

STEP 5
1. Attach top board (1) to pre-assembled unit by inserting cam bolts (A) into cam lock holes
and inserting wood dowels (C) into wood dowel holes on left side panel (2) and right side
panel (3).
2. Insert 4 cam locks (B) into cam lock holes on left side panel (2) and right side panel (3),
then rotate clockwise to secure cam bolts in place.
STEP 6
1. Attach upper back board (11) and middle back board (12) to back of cabinet by inserting
20 screws (M) through holes on upper back board (11) and middle back board (12), then
tighten to back of cabinet.

STEP 7
1. Attach left door (5) to left side panel (2) by inserting 4 screws (J) through holes on metal
hinge (D), then tighten to left door (5).
2. Repeat above step to assemble right door (4).
STEP 8
Option #1: Securing to Drywall
1. Using wall mounting paper template to determine position, screw 2 plastic anchors (O) into
drywall.
2. Insert 2 screws (N) through holes on inside of cabinet and into plastic anchors (O) and tighten.
Option #2: Securing to Drywall and Wood Stud
1. Insert 2 screws (N) through holes on inside of cabinet, then tighten through drywall and into
wood stud.

ATTENTION ADULTS: Cabinet should be checked periodically for damage or
loose screws/parts. Take appropriate action necessary to correct hazards such as
tightening of screws and taking any damaged parts away from children.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
IMPORTANT:
Keep assembly instructions for future reference.

Enjoy your new cabinet!