Rohnson R-837 User manual

INSTRUCTION MANUAL
TABLE FAN 40cm R-837
220–240V~ 50Hz 50W
BEFORE OPERATING THIS PRODUCT, READ, UNDERSTAND, AND
FOLLOW THESE INSTRUCTIONS.
BEFORE FIRST USE
1. General Safety Instructions
Read this instruction manual thoroughly before using the
appliance and save it for future reference and if necessary
pass the instruction manual on to a third party.
WARNING: When using electrical appliance, basic safety
precautions should always be followed to reduce the risk of
fire, electrical shock and personal injury
1) General
1. Check if the electrical specifications of this appliance are
compatible with your installation.
2. To protect against electrical hazard, do not immerse in
water or other liquids. Do not use near water.
3. This appliance is for indoor use only.
4. Do not place objects on top of the unit.
5. Do not unplug the unit if your hands are wet, electrical
shock could occur.
6. Do not carry the appliance while it is operating.
7. Place it on a secure and level area. Keep out of reach of
children to prevent any accident.
8. Unauthorized use and technical modifications to the
appliance can lead to danger to life and health.
9. Do not push any object into the appliance. Do not
disassemble the appliance.
10. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for
their safety.
11. Children should be supervised to ensure that they do
not play with the appliance.
12. Ensure that the fan is switched off from the supply
mains before removing the guard.
2) Electrical safety
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
2. Specific Safety Rules
Disconnect from mains before maintenance or cleaning.
Ensure that the fan is switched off from the supply mains
before removing the guard.
.
4. Features of This Product
UNPACKING
Unpack the fan from the gift box.
Retain the carton and packing for future use. If you have to
dispose of the carton and packing, please do so
responsibly.
Guard
Fan Motor
Switch
Base
Blade

PRODUCT ASSEMBLY
BASE ASSEMBLY
- Put the round base on the flat ground
- There are 3 screws labeled on the base plate, take them
out before assembled.
- Put the whole body into the base plate
- Fasten the screws on the bottom of base plate. Do not
over-tighten the screws.
-
HOW TO ASSEMBLE THE FAN
- Remove the locking nut and blade cap from the motor
spindle (Fig.1)
- Place the rear guard into position. If this is done correctly,
the carry handle will be at the top (Fig.2),
- Fix the rear guard into position by replacing the locking
nut tightly by hand (Fig. 3). Do not force the locking nut.
- Press the fan blade (Fig.4) and locking the blade cap by
turning it clockwise
- Lift out all locking clips on the front guard (Fig 5).
- Place the front guard into position and secure it by
fastening the clips over the outer rim. The screw and nut
at the bottom of the guard must be tightened (Fig. 6).
-
-
-
-
(Fig.1) (Fig.2)
(Fig.3) (Fig.4)
(Fig.5) (Fig.6)

5. Operation Of The Product
1. On / Off and Speed Control
The ON/OFF and Speed is controlled by the rotary
Switch.
0- The Fan is switched Off
1- The Fan operates at the Low speed
2- The Fan operates at the middle speed
3- The Fan operates at the high speed
2. Oscillation Adjustment
Push the oscillation control to turn on the oscillation
function, pull the oscillation control to turn it off. (Fig.7)
(Fig.7)
6. Cleaning
⚫Caution! The device must be turned off and unplugged
before every cleaning.
⚫Once the fan is assembled, it is forbidden to
disassemble the grids (guard) when cleaning.
⚫Clean the fan, including the safety guard, with a dry
dust cloth
⚫Keep the air vents at the rear of the main body free
from dust or fluff–use a vacuum cleaner to remove
these when necessary. Do not probe any opening to
remove fluff.
⚫Do not allow any water or other liquid to enter the motor
housing.
CAUTION: Do not use harsh detergents, chemical cleaners
or solvents to clean the fan.
IMPORTANT INFORMATION FOR CORRECT DISPOSAL
OF THE PRODUCT IN ACCORDANCE WITH EC
DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be
disposed of as urban waste. It must be taken to a special
local authority differentiated waste collection center or to a
dealer providing this service. Disposing of a household
appliance separately avoids possible negative
consequences for the environment and health, deriving
form inappropriate disposal and enables the constituent
materials to be recovered to obtain significant savings in
energy and resources. As a reminder of the need to dispose
of household appliances separately, the product is marked
with a crossed-out wheeled dustbin.