Rohnson R-849 User manual

STAND FAN 2 IN 1 ( 16”- 40cm)
Model: R-849
INSTRUCTION MANUAL

(PLEASE READ THIS USER’S MANUAL
THROUGHLY BEFORE USING.)
⚫Safety Instruction
1. Never put your finger or other something into the
cover to avoid any hurts.
2. Make sure to keep the fan far away from humidity,
chemical articles and oil.
3. While cleaning, be sure not to splash water and do
not use oil, alcohol or chemical articles as they may
cause distortion of fan body and cause electrical
hazards.
4. Do not pull out the power supply plug by pulling
power supply cord, which may lead to electrical
shock or generating electrical shock.
5. Keep away from curtain, clothing or other something
may affect the fan’s working.
6. Turn off all switches and pull out power supply plug
when you go out for a long time.
7. Never use the fan before finishing assembly to avoid
any hurts.
8. If the supply cord is damaged, it must be repaired by
the manufacture or its service agent or a similarly
qualified person in order to avoid a hazard.
9. If the until doesn’t work before sending for
maintaining. Please check the plug of the power
supply has been inserted into socket with electricity.

10. Do not use the electric fan in rain.
11. This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
⚫Parts Description of R-849

1. Clamping ring
2. Front guard
3. Blade fastening screw
4. Fan blade
5. Guard fastening screw
6. Rear guard
7. Motor shaft
8. Control panel
9. Upper standing shaft
10. Lower standing shaft
11. Standing base
12. Screws
13. Remote control

⚫ASSEMBLING INSTRUCTIONS
Base and Standing ShaftAssembly
a. Attach the lower standing shaft onto the standing
base. Use screws to fix the shaft firmly.
b. Insert the upper standing shaft into the lower
standing shaft, turning the upper standing shaft
clockwise to tighten the connection of the two
shafts.
The Whole Assembly
a. Remove the blade fastening screw and guard
fastening screw from the motor shaft spindle.
b. Fit the rear guard by positioning with the location
pins. Secure the guard onto the motor body with
the guard fastening screw.
c. Place the fan blade onto the motor shaft by
marching the slot with the shaft pin. Fix the blade
by tightening the blade fastening screw in a
counter-clockwise direction. Check that the fan
blade can rotate freely by turning it with your
hand.
d. Put the front guard against the rear guard and fix
with the clamping ring. Make sure the clamping
ring is set properly at the rim of the fan guards.
Tighten the screw on the clamping ring.

OPERATION
Connect the appliance to a suitable power source. Then
press the control panel or the remote control to choose
your desired functions.
1. ON/OFF: Press to turn the appliance on. It
will work with the following presetting: Speed: low /
Mode: normal / Timer: off / Swing: off
Press again to turn off the appliance.
2. SPEED: Press to adjust the speed.
“1”: low wind, “2”: medium wind, “3”: high wind
3. MODE: Press to choose the model functions
from Normal -> Natural -> Sleeping -> …. (Repeating)
1) Normal: under this mode, you can press to
choose speed Low / Mid / High
2) Natural: under this mode, the appliance will operate as
follows: 5 seconds medium wind -> 5 seconds low wind
-> 5 seconds medium wind -> 5 seconds high wind -> 5
seconds medium wind -> 5 seconds low wind -> stop 3

seconds… (Repeating)
3) Sleeping: under this mode, the fan will operate as
follows:
5 seconds medium wind -> 10 seconds low wind -> 5
seconds medium wind -> 5 seconds low wind -> 5
seconds medium wind -> 10 seconds low wind -> stop 3
seconds…(Repeating)
Note: In natural mode or sleeping mode, the motor works
with the preset speed. That is, the speed button cannot
control the speed under these two modes.
4. TIMER: Press to set your desired working
time from 1h-> 2h -> 3h -> …7h -> off. When the set
time has elapsed, the fan will be off and under standy
condition.
5. SWING: Press to control the oscillation
function on or off.
6. Tilting angles: By pushing the fan-guard, you can
adjust the fan to the preferred elevation.
NOTE: In case you want to turn the stand fan into table
fan, use the extra accessory that is provided in the
package.

CLEANING
a. Before servicing the fan and after each occasion of use,
switch off the appliance and unplug the mains cable from
the socket.
b. Never immerse the appliance in water (danger of
short-circuit). To clean the appliance, only wipe it down
with a damp cloth and dry it carefully. Always take out
the mains plug first.
c. Take care that excessive dust does not build up in the
air-intake and air-outlet grille and clean it occasionally
using a dry brush or vacuum cleaner.
TECHNICAL DATA
Operating voltage: 220-240V~ 50Hz
Power consumption: 55W

IMPORTANT INFORMATION FOR CORRECT
DISPOSAL OF THE PRODUCT IN ACCORDANCE
WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be
disposed of as urban waste. It must be taken to a special
local authority differentiated waste collection centre or to
a dealer providing this service. Disposing of a household
appliance separately avoids possible negative
consequences for the environment and health, deriving
form inappropriate disposal and enables the constituent
materials to be recovered to obtain significant savings in
energy and resources. As a reminder of the need to
dispose of household appliances separately, the product
is marked with a crossed-out wheeled dustbin.