Rohnson R-859 User manual

STAND FAN WITH REMOTE CONTROL R-859 40cm
220~240V/50Hz 45W
INSTRUCTION MANUAL
Please read carefully and save these instructions

CAUTION
Read and retain these instructions for future use.
Improper installation may result in the risk of fire, electric shock, or serious injury to persons.
Power plug must be removed from power socket before cleaning, servicing, maintenance and
when moving from one location to another. The fan should be placed on a flat and stable surface
when operating to avoid overturning.
The fan should not be placed in a damp place or where humidity is high (such as in a bathroom).
Do not insert fingers or other objects through the fan guard.
Unplug from mains if not in use.
This is not a toy. Keep out of reach of children.
The appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not play with the appliance.
If the cord is damaged, it should be replaced by service agent or qualified technician.

PARTS DESCRIPTION
PARTS
1. Front Guard 9. Switch Box
2. Clip 10. Extension Pole
3. Spinner 11. Pole Clamp
4. Blade 12. Base Tube
5. Nut 13. Base Cover
6. Rear Guard 14. Base
7. Shaft 15.base fixing screws
8.Motor 16. Remote Control

CONTROL PANEL
ASSEMBLY INSTRUCTIONS
Settle the four screws to the round base and attach the lower base tube (12) to the base using a
screwdriver (not supplied). Unscrew and remove the pole clamp (11) down over the adjustable and
lower base hole {13 & 14) until it is in place over the screws. Replace the pole clamp (11) and at
the same time raise the extension Pole (10). Attach the fan assembly on top of the pole and tighten
the Switch box retaining screw.
NB the extension Pole (10) can sometimes slip inside the lower base pole (12) during transit.
Remove the Rear Guard Central Fixing (5) nut. Place the rear guard (6) onto the motor housing (8)
and replace the Rear Guard Central Fixing (5) nut by screwing back on clockwise.
Take the fan blade (4) and slide it onto the motor spindle (7) ensuring that notches on the rear line
up with the splines on the shaft. Screw on the Blade Retaining Nut (3) in an anticlockwise direction.
Turn the five clips (2) around the outside edge of the front guard outwards.
Hang the front guard (1) over the top of the rear guard (6) and push the clips inwards until the
front guard is fastened to the rear guard.
BEFORE USE
• Avoid placing fan near curtain and small corners to enjoy maximum airflow.
• Do not handle power plugs with wet hands, to avoid risk of electric shock.
• Fans in the process of operation, please avoid to insert hands or other objects in the functioning
of the blade.
1. Sleep mode
2. Normal mode
3. Natural mode
4. High Speed
5. Medium Speed
6. Low Speed
7. Swing Button
8. Mode Button
9. Timer
10. Speed/On Button
11. Off Button
12. Timer Light
REMOTE CONTROL
13. Swing Button
14. Timer Button
15. Speed/On Button
16.Mode Button
17.Off Button
REMOTE CONTROL

• Remove the packaging materials and unravel the cord completely before operation.
• Choose "on/speed button" to start your fan and select the desired speed (Low, Medium, High)
To switch OFF, press OFF button.
Please check that the voltage indicated on the product corresponds with your supply voltage.
Operating Instructions
Place the fan into the desired position ensure that it is level.
The fan can be tilted vertically up and down by moving the guard assembly up and down to the
desired position. NB
do not amend the fan whilst connected to the mains.
Slacken the pole clamp (11) and adjust the fan to the desired height, tighten the pole clamp once
the desired height
is set. Insert the mains plug into the nearest socket and then press the button to turn the fan on.
THE FIRST BUTTON ON THE PANEL IS INACTIVE FOR THE FAN. NO FUNCTION.
Speed Control
When the fan is turned on, it starts at the speed setting.
Select the desired speed by pressing the "ON/Speed" button:
Press Once: Speed 1 will be on and the corresponding pilot light will be on.
Press Twice: Speed 2 will be on and the corresponding pilot light will be on.
Press Three times: Speed 3 (max) will be on and the corresponding pilot light will on.
Set Timer
Press 'Timer" button and select 30min/1h/2h/4h.
When 30min, 1h, 2h, 4h are all lighted on, the timer is set for 7.5hr(maximum).
Sleep Mode
Switch the "Mode" button between normal and sleep mode.
On "normal mode": The motor runs continuously. Choose among low, medium and high speed.
On "sleep mode" and "natural mode", the motor runs discontinuously.
Natural mode: the machine will run at a low RPM browse wind just like as breeze, and it is closer
to the natural wind, making the body cool and comfortable. If the fan works under "Natural" model,
it will start from low speed for 2-3 seconds and accelerate peed to middle speed for 1-2 seconds,
then next 1-2 second will reach highest speed. After then, fan motor will slow down speed for 2-3

seconds. The machine will repeat this process continuously.
Sleep mode: The unit starts 2-3S linear acceleration to high speed, and then 3S deceleration. The
machine will repeat this process continuously.
Off
Press "Off" button to stop the programs and the fan.
Remote Controller
All buttons are the same as above explanations
Oscillation
Press the Swing button to enable the fan to oscillate from side to side. Press again to stop
oscillation. You can also set oscillation from remote control.
• Please retain your purchase docket and gift box which must be presented as proof
of date of Purchase if you wish to claim under the terms of the Guarantee.
• If the product has been 'ABUSED' or 'OPENED AND TAMPERED WITH' in any way,
the Terms of the Guarantee are invalidated.
CLEANING
• ALWAYS UNPLUG BEFORE CLEANING YOUR FAN!
• Plastic parts should be cleaned with mild soap and a damp cloth or a
sponge. Thoroughly remove soap with a clean cloth.
• Do not allow water to run into the interior of the fan as this could
cause electrical shock or start a fire.
• Store fan in a clean, dry place when not in use.

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH
EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as urban waste. It must be taken
to a special local authority differentiated waste collection center or to a dealer providing this
service. Disposing of a household appliance separately avoids possible negative consequences for
the environment and health, deriving form inappropriate disposal and enables the constituent
materials to be recovered to obtain significant savings in energy and resources. As a reminder of
the need to dispose of household appliances separately, the product is marked with a crossed-out
wheeled dustbin.