Rohnson R-863 User manual

Metal Table Fan 30cm
R-863 / R-864 / R-867
PLEASE READ INSTRUCTIONS CAREFULLY
BEFORE OPERATING

Sleek &modern high-velocity fan provides more powerful wind than ordinary plastic fans. Draws air off the floor
and circulate through the entire room keeping room cool and breezy. Put near the windows and it helps exhaust
hot indoor stuffy air and pulls in fresh outdoor air.
PARTS DESCRIPTION
2
1 Oscillation Button
2 Motor Shaft
3 Motor Unit
4 Large Set Screw
5 Control Switch
6 Base
7 Guard Mounting Screw
8 Rear grille
9 Blade
10 Front grille
11 Clamps
12 Plug and Power Cord

ASSEMBLING BLADESAND GRILLES
1. Place the rear guard (8) from the front on to the motor unit (3). Align
grille (8) so that all four screw holes overlap and use the supplied screws to
attach it to the motor unit (3).
2. On to the shaft (2), place the fan blades (9) with the collar facing
forward. Align the blades (9) so that the screw in the collar points above the
flat groove in the shaft (2). Hold the fan blades (9) in this position and
tighten the screw.
3. Release all clamps along the perimeter of the front grille (10). Place
the front grille (10) against the rear grille (8) so that the rear grille (8) slides
into the hook located on the top end of the grille (10), and so that the screw
holes at the bottom of both the grille (8) & (10) overlap, see figure A1 and
A2. Secure all the clamps along the perimeter of the front grille (10) by
tilting them down towards the edge of the grilles (8) and (10). And then
screw the supplied screw with the nut into the overlapping holes in the
bottom part of the grilles (8) and (10).
Figure A1 Figure A2

Operating Instructions:
a) Ensure voltage used corresponds with the voltage indicated.
b) Turn the speed control to selected speeds: 0(off) and speedsⅠ,Ⅱ,Ⅲ
is Slow, Middle, Fast.
c) Tilting angles-By pushing the tilt-guard, you can adjust the fan to any
elevation preferred. Pushing the fan head can tilt the fan. But user should
loosen the screw firstly.
SECURITY GUIDE
◆Never touch the blades with hand or any object!
◆Do not pull the cord too hard. If damaged after pro-long use, get it
repaired by any electrical repairman
◆This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
◆Children should be supervised to ensure that they do not play with the
appliance.
◆If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard.
CLEANING
To clean: Disconnect the power cord from the mains. Remove the guard and
the blades carefully. Do not drop the blades! First use soft cloth with light
soap to clean off oil stains. Then wipe and polish with dry cloth. Never use
polish or any corrosive liquid that will damage the paint, metal or plastic!
Put back the blades and lock the guard securely before use.
NO exchange will be entertained if the above instructions are not followed.
TECHNICAL INFORMATION
Operating Voltage: 220-240V~ 50Hz
Power Consumption: 35W

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as urban
waste. It must be taken to a special local authority differentiated waste
collection center or to a dealer providing this service. Disposing of a
household appliance separately avoids possible negative consequences for
the environment and health, deriving form inappropriate disposal and
enables the constituent materials to be recovered to obtain significant
savings in energy and resources. As a reminder of the need to dispose of
household appliances separately, the product is marked with a crossed-out
wheeled dustbin.