Ronbow MARQEE LED MEDICINE CABINET 619718-FINISH Assembly instructions

INSTALLATION AND CARE GUIDE
MARQEE LED MEDICINE CABINET
619718-FINISH

170728ronbow.comINSTALLATION SHEET
2
MARQEE LED Medicine Cabinet
Model : 619718-FINISH
Tools Required
MATERIALS INCLUDED
1 LED Medicine Cabinet
2 small mounting bracket
1 large mounting bracket
10 wood screws
6 screw covers
1 cut out template (For recess
mount)
Wiring Diagram :
NOTE : ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENCED ELECTRICIAN.
WARNING: To reduce the risk of electrical shock, shut o power before wiring the cabinet
CAUTION: Requires 120V 20AMP circuit.
CAUTION: The LED mirror must be wired to a 20AMP GFI (ground fault interrupter)circuit breaker
when used in bathrooms and all other locations required by the national electirc code.
120VAC
20A GFI
CIRCUIT BREAKER FIELD CONNECTION
Black = Ground
Red = Positive
White = Negative
Black = Ground
Red = Positive
White = Negative
LED
LED MIRROR CABINET

170728ronbow.comINSTALLATION SHEET
3
MARQEE LED Medicine Cabinet
Model : 619718-FINISH
Step 1:
Figure 1.
Determine the ideal location of your new
mirror.
SURFACE MOUNT INSTALLATION minimum to ceiling
minimum to faucet
1”
1”
See Figure 2.
Measure the height of the medicine cabinet and
place the 2 x 4 supporting beam on the top and
bottom behind the desired location for structural
support and patch up the wall.
Step 2: Figure 2.
See Figure 1.

170728ronbow.comINSTALLATION SHEET
4
MARQEE LED Medicine Cabinet
Model : 619718-FINISH
See Figure 3.
Slide in the top and bottom hanging bracket to
the track as shown on the right.
And screw the mirror at the support beam
location to secure the installation.
Step 3: Figure 3.
SURFACE MOUNT INSTALLATION- CONTINUE
See Figure 4.
Place the cut out template at the desired location
and cut open to create a supporting box with 2x4
supporting beam, the supporting beam should be
flush with the openings.
Step 1:
RECESS MOUNT INSTALLATION
Figure 4.

170728ronbow.comINSTALLATION SHEET
5
MARQEE LED Medicine Cabinet
Model : 619718-FINISH
See Figure 5.
Remove the mirror door by lift the release
tab of both hinges, and carefully remove the
cabinet door.
Step 1:
RECESS MOUNT INSTALLATION- CONTINUE
Figure 5.
release
tab
Remove the three screws on the electrical
box on the top and flip down the cover to
gain access to the last screws in order to
remove the decorative side panels.
Step 2:
Remove the three screws from both side
of the cabinet interior and remove the
decorative side panel and beginning recess
mount installation.
Step 3:

170728ronbow.comINSTALLATION SHEET
6
MARQEE LED Medicine Cabinet
Model : 619718-FINISH
After removing the screws from both side of
the interior cabinet, you may remove the two
decorative panel and put it aside.
Step 4:
RECESS MOUNT INSTALLATION- CONTINUE
Figure 6.
See Figure 6.
For the recess installation, you may remove
the 2 small mounting bracket and 1 large
mounting bracket on the top.
Step 5:

170728ronbow.comINSTALLATION SHEET
7
MARQEE LED Medicine Cabinet
Model : 619718-FINISH
Figure 7.
Connect the cabinet wire to your home
electricity.
ALL WIRING SHOULD BE DONE BY A
QUALIFIED LICENCED ELECTRICIAN.
Then insert the cabinet body to the wall and
use the wood screws to secure the cabinet to
the supporting beam.
Step 6:
See Figure 7.
Close the electrical box and conceal the box
with the screws removed.
Step 7:
NOTE: To conceal the screw, please place the
screw cover through the screws before secure
down the cabinet to the wall
Connect the hinges back together to
complete the installation.
Step 8:
RECESS MOUNT INSTALLATION- CONTINUE
Figure 8.
See Figure 8.

170728ronbow.comINSTALLATION SHEET
8
MARQEE LED Medicine Cabinet
Model : 619718-FINISH
ADJUSTING THE HINGE
Locate the screw pictured in Figure 7.
Turn the screw clockwise or counter-
clockwise to move the door from left
to right
Left to Right
See Figure 9.
Figure 9.
Figure 10.
Locate the screw pictured in Figure 10.
Turn the screw clockwise or counter-
clockwise to move the door inward
and outward
Inward to Outward
See Figure 10.
Switch the tab to turn on and o the
damper for the slow close function
Slow Close Function
See Figure 11.
Figure 11.
Damper
On/OFF
Inward to
Outward
Left to Right
https://youtu.be/uToOh01OM6M