Royal Sovereign ES-400 User manual

Photo Laminator
OWNER'S MANUAL
ES-400
PLEASE READ AND SAVE INSTRUCTIONS
ROYAL SOVEREIGN INTL.INC.
- 1 -
EDNord - Istedgade 37A - 9000 Aalborg - telefon [phone]

TOPICS PAGE
MAJOR PARTS ------------------------------------------
-
2
INTRODUCTION -----------------------------------------
-
3
SAFETY PRECAUTIONS ------------------------------------
-
3
OPERATING INSTRUCTIONS --------------------------------
-
4
HOW TO CLEAN THE ROLLERS ------------------------------
-
4
TROUBLESHOOTING -------------------------------------- 5
SPECIFICATIONS ----------------------------------------
-
5
TABLE OF CONTENTS
MAJOR PARTS
Ready Lamp
Power Switch Base
Cover
Power Cord
- 2 -
EDNord - Istedgade 37A - 9000 Aalborg - telefon [phone]

Thank
y
ou for
p
urchasin
g
Ro
y
al Soverei
g
n's new EL line. This has been desi
g
ned and
manufactured to
p
rovide both
p
rofessional and non
p
rofessional service in a wide ran
g
of environment es
p
eciall
y
in a
p
icture environment. For
p
ro
p
er usa
g
e and maintenanc
read and follow carefully. Since it covers all models within this line, there may be
sections that do not apply to your machine. Please follow instructions that specially
apply to your model.
The safety recommmendations outlined in this section are to be read and followed
before operating the machines. Keep this information for future reference. Failure to
comply with any of the following safety procedures could result in serious
injury.
1. To prevent the possibility of electrical shock, do not immerse machine in water or
permit liquids to get inside.
2. To prevent the possibility of fire, do not allow articles of clothing (neckties,
scarves, paper etc.) to get inside.
3. Do not insert sharp objects (pin, clip, coin etc.) into front or rear openings of the
machine.
4. Do not attempt to laminate items that exceed total recommended material thickness.
5. Do not operate machines for any other purpose other than its intended use.
6. Do not use when the electric plug is cracked or deformed.
7. Turn off the power when unattended or not in use. Unplug machine before moving
or when it is not in use for an extended period of time.
8. This machine is intended for indoor use only.
9. Do not alter the electric plug in any way.
INTRODUCTION
SAFETY PRECAUTIONS
- 3 -
EDNord - Istedgade 37A - 9000 Aalborg - telefon [phone]

10. During the operation, the machine has high heat. Keep children away from
the machine.
11.To reduce the risk of electric shock, this appliance has a polarized plug
(one blade is wider than the other). This plug will fit in a polarized outlet only
one way. If the plug does not fit fully in the outlet, reveres the plug. If it still does
not fit, contact a qualified electrician to install the proper outlet. Do not change
the plug in any way. ( Ac120V only)
1. Place and use the laminator on a sturdy, flat work surface.
2. Plug the laminator into a power source that matches the laminator's rate of voltage.
3. Press the power switch to 'ON' position.
(Red lamp will illuminate and the motor starts to operate.)
4. Allow approximately Max 9minutes to preheat. When the proper temperature is
reached, the 'READY' light will illuminate.
5. After 'READY' li
g
ht is li
g
hted com
p
letel
y
,
p
lace the item to be laminated in the laminati
n
pouch and insert pouch squarely into the front opening.
(Do not laminate pouch film only without an item. Do not use unsealed pouch film.
It causes jams.)
6. After the finished laminated item is fed completely out through the rear
of the laminator, insert another pouch into the front opening.
7.Turn off the machine and use plug off completely from a power source.
8. After cooling down completely, keep the place to avoid the direct light.
When melted adhesive is found at the surface of finished item, insert 0.5mm thick white
paper into the front opening and let it pass through the laminator.
Then, the melted adhesive stuck to the roller can be removed.
Periodical roller cleaning keeps high quality lamination.
HOW TO CLEAN THE ROLLER
OPERATING INSTRUCTIONS
- 4 -
EDNord - Istedgade 37A - 9000 Aalborg - telefon [phone]

330
1.2 (2.64 lbs.)
Power Consumption(W)
Laminating Speed(mm/min)
AC 100V.120V.220V∼240V.60Hz/50㎐
100
Weight(kg)
Voltage/Cycle
Cold Function
Heat Source
Ready Time
Motor Type
Max.Laminating
Thickness(mm)
Film Thinckness(micron)
Number of rollers(EA)
Reverse Function
ES-400DESCRIPTION
Dimensions(w*d*h )
Max.Laminating Width(mm)
8.26" x 5.11" x 3.34"
110 ( 4.33")
TROUBLESHOOTING
Symptom Check Point
75 ~ 100 (3 - 4 mil)
2
NO
210×130×85 (mm)
SPECIFICATIONS
Mortor doesn't work.
1. Check if the power cord is plugged in.
2. Check if the switch is on.
AC
1.2
NO
Hot shoe
Max 9min
- 5 -
EDNord - Istedgade 37A - 9000 Aalborg - telefon [phone]

Terms and Conditions
1. This Warranty applies to repair or replacement of product found to
be defective in material or workmanship for one year from the date
of original purchase. This warranty is extended only to the original
purchaser.
2. This warranty does not apply to damage resulting from, abuse,
misuse, or improper maintenance or damage that is attributable
to acts of God. Royal Sovereign is not liable for incidental or
consequential damages of any nature. This limitation would not
apply if you live in those states that do not permit the exclusion
or limitation of incidental or consequential damages
3. Royal Sovereign will repair or replace this product if it is found
defective in material or workmanship. Defective product must be
returned to Royal Sovereign, freight prepaid, with proof of purchase
and $ 10.00 for handling, return packaging and shipping charges.
4. Return defective product to the following address with a detailed
description of the problem. Please pack it in its original carton with
return address. All shipping charges must be paid by sender.
CALL ROYAL SOVEREIGN FOR ALL YOUR LAMINATING NEEDS
[phone]
ROYAL SOVEREIGN INTL., INC.
ES-400 100 WEST SHEFFIELD AVENUE
ENGLEWOOD, NJ 07631-1809
Tel : [phone]
Fax : [phone]
LIMITED ONE YEAR WARRANTY
- 6 -
EDNord - Istedgade 37A - 9000 Aalborg - telefon [phone]