Royal Sovereign RSC-5500H User manual

RSC-5500H/6500H
Royal Sovereign International Inc.
Owner's Manual
GRAPHIC LAMINATION
PRODUCTS
Please read and retain these instructions.
To register your product, please go to www.royalsovereign.com
www.royalsovereign.com

Graphic Lamination Products
INTRODUCTION
Thank you for choosing a Royal Sovereign laminator. It has been designed and
manufactured to provide years of continuous service.
For complete operating and maintenance information please read this manual
thoroughly. Upon receipt of your laminator, please inspect the box, the machine and all
other contents for shipping damage.
Damage should be brought to the immediate attention of the delivering carrier
(See page 6 for list of shipment elements).
Model RSC-5500H/6500H

3
CONTENTS
Introduction 2
Safety Precautions 4
Installation 5
Included With Laminator 6
Product Identification7
Operation 8
Control Panel 8
Loading Film 9
Threading Film And Setting Nip Guide10
Pressure Setting 11
Decaling 12
Mounting 12
Maintenance 13
Troubleshooting 13
Specifications 14
Warranty 15

4
SAFETY PRECAUTIONS
Failure to comply with any of the following safety procedures could result in serious injury. Please read the instructions
carefully and keep for future reference.
1. Only a licensed electrician should install wiring and outlet for the laminator.
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
3. Keep hands and clothing (i.e. Neckties) away from rollers. The rollers have pinch points that can trap body parts or
clothing and cause serious injury.
4. Keep flammable and wet objects away from the machine.
5. Place machine on a level surface,then set the moveable foots down to floor to keep the machine steadily.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/or repairing.
8. Keep out of reach of children.
9. Only Royal Sovereign authorized maintenance and service technicians should make repairs.
10. Do not attempt to laminate items that exceed total recommended material thickness for the unit
11. When cleaning the machine, don't use flammable sprays or materials.
12. Do not touch the rollers when they are hot or place foreign objects inside the machine.
13. Do not cover the surface of the machine until the machine has completely cooled.
14. If emergency happen, press emergency switch immediately.
15. Temperature of circumstance: 20°C ± 5°C; humidity of circumstance: < 95%(20°C ± 5°C).
16. Warning - Hazardous Moving Parts – Keep Fingers And Other Body Parts Away.

RSC-5500H/6500H
5
INSTALLATION
Note: The laminator should be installed by a trained service technician.
The laminator comes fully assembled, except for the feed table and paper guide to avoid shipping damage. Upon arrival,
thoroughly inspect the unit. It is imperative that any shipping damage is reported and a claim is filed with the delivering
carrier immediately upon receipt.
The laminator should be located in an area with adequate work space for feeding graphics and lamination materials.
Avoid placing the laminator in a dusty area or near sources of extreme heat or cold.
Once the laminator is in place, lock the casters into position(“ON” and adjust the moveable foots to keep machine steadily
position). Always unlock the casters (“OFF” position) when moving to a different location.
ELECTRICAL REQUIREMENTS
Royal Sovereign recommends that a licensed electrician ensures proper power installation to your laminator in accordance
with electrical codes in your area.
The laminator should have a dedicated power line.
120V UL 230V UL 240V UK
220V EU 220V AU

6
INCLUDED WITH LAMINATOR
Thoroughly inspect the parts and the unit. It is imperative that any missing parts are reported and a claim is filed with the
reseller immediately upon receipt of shipment.
Part Name Quantity Picture
Laminator 1
Owner's Manual 1
Spare Motor Fuse - FUSE(50T)
(6.3A) 1
Spare Main Power Fuse - FUSE(65TS)
10A/20A 1

RSC-5500H/6500H
7
PRODUCT IDENTIFICATION
1Shaf Release Liner 12 Caster (Unlock)
2Emergency Switch 13 Power Switch
3Roller 14 Shaft Rear Rewinder
4Safety Sensor 15 Nip Setting Wheel
5Table Front 16 Button
6Speed Sensor 17 Knob Speed Control
7Caster (Clock) 18 Control Panel
8Foot 19 Idle Bar
9Foot Switch 20 Shaft Film
10 Shaft Front Rewinder 21 Stop Ring
11 Shaft Feeder 22 Tension Knob
2
1
3
5
6
7
8
4
10
9
11
12
13
15
14
16
17
18
2122 1920

8
OPERATION
CONTROL PANEL
Pressure
Indicate the roller pressure value(according to the
different material and different size to set a
reasonable pressure value) from 0~9.
• See page11.
Heat
To change the mode from cold to hot or oppositely.
Temperature for hot mode on upper rpller is
max.122˚F 50˚C.
Reverse To reverse the rollers, press and hold the button.
Speed
Rotate the knob to control the roller’s speed from
0 to 8.5m/min. (Ensure the speed sensor is
working that something is placed on it. )
Run To start the rollers.
Stop To stop the rollers.
Safety
The LED will flash when the beam of the optical
safety device at the input side of the nip is not
interrupted.
USING FOOT PEDAL
Place the foot pedal on the floor in front of the machine. Once all correct settings are displayed, you may use the foot
pedal to operate the laminator for “Hands Free Operation.”
1. To activate the machine, press the foot pedal once and then release. Repeat to stop the rollers.
2. Press the foot pedal and hold to get slow speed mode to put or set the laminating film or medium.
Note: In slow speed mode, the safety laser sensor is inoperative.

RSC-5500H/6500H
9
LOADING FILM
Royal Sovereign films are wound with the adhesive side facing the inside of the roll (adhesive in).
Loading film to upper film shafts:
1. Loosen the stop ring and take down the film shaft, then
load the film and center it on the shaft.
Note: The adhesives should be facing you.
Figure 1
Figure 2
2. Load the film shafts on the machine (figure 3) and
tighten the stop ring to lock the film shaft to the
appropriate location.
Figure 3
Figure 4

10
THREADING FILM AND SETTING NIP GUIDE