Royal Sovereign RSL-2700 User manual

RSL-2700
Royal Sovereign International Inc.
Owner's Manual
GRAPHIC LAMINATION
PRODUCTS
Please read and retain these instructions.
To register your product, please go to www.royalsovereign.com
www.royalsovereign.com

Graphic Lamination Products
INTRODUCTION
Thank you for purchasing a Royal Sovereign RSL-2700 table top laminator. It has been designed and
manufactured to provide years of continuous service. For complete operating and maintenance information
please read this instruction manual thoroughly. Upon receipt of your laminator thoroughly inspect the box,
machine and all other contents. It is imperative that any shipping damage is reported and a claim is filed with
the delivering carrier immediately upon receipt.
Model RSL-2700

RSL-2700
3
CONTENTS
Introduction ........................................................................................ 2
Package Contents .................................................................................. 4
Safety Precautions................................................................................. 4
Parts ................................................................................................... 5
Inlay Control.......................................................................................... 6
Loading Film ......................................................................................... 7
Threading Film
Hot Film-Double laminating.................................................................. 8
Maintenance.......................................................................................... 9
Troubleshooting..................................................................................... 9
Specifications ...................................................................................... 10
Warranty............................................................................................. 11

4
PACKAGE CONTENTS
SAFETY PRECAUTIONS
Failure to comply with any of the following safety procedures could result in serious injury. Please read the instructions
carefully and keep for future reference.
1. Only a licensed electrician should install wiring and outlet for the laminator.
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
3. Keep hands and clothing (i.e. Neckties) away from the roller. The rollers have pinch points that can trap body parts or
clothing and cause serious injury.
4. Keep flammable and wet objects away from the machine.
5. Place machine on a level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/or repairing.
8. Keep out of reach of children.
9. Only Royal Sovereign authorized maintenance and service technicians should make repairs.
10. Do not attempt to laminate items that exceed total recommended material thickness for the unit
11. When cleaning the machine, don't use flammable sprays or materials.
12. Do not touch the rollers when they are hot or place foreign objects inside the machine.
13. Do not cover the surface of the machine until the machine has completely cooled.
Owner's Manual

RSL-2700
5
PARTS
1. Upper Film
2. Left Cover
3. Safety Cover
4. Table Front
5. Lower Film
6. Right Cover
7. Inlay Control
8. Idle Bar
9. Tension Blot
12
3
9
4
8
5
7
6

6
CONTROL PANEL
POWER When connected the power, the light will always be on.
TEMP.
1.5 mil : To laminate film thickness of 1.5 mil (230˚F~270˚F)
3.0 mil : To laminate film thickness of 3.0 mil (270˚F~310˚F)
* When the machine is ready, the light will be always on.
working temperature may vary depending on the film manufacturer.
If laminating comes out cloudy, then select the higher temp. setting.
REVERSE To reverse the rollers
RUN / STOP To start or stop rollers
Note: After ready, if no activity is made within 30min after each use, the machine will
automatically switch into stand-by mode (Temperature will automatically reset to
176°F (80°C).

RSL-2700
7
CONTROL PANEL
POWER When connected the power, the light will always be on.
TEMP.
1.5 mil : To laminate film thickness of 1.5 mil (230˚F~270˚F)
3.0 mil : To laminate film thickness of 3.0 mil (270˚F~310˚F)
* When the machine is ready, the light will be always on.
working temperature may vary depending on the film manufacturer.
If laminating comes out cloudy, then select the higher temp. setting.
REVERSE To reverse the rollers
RUN / STOP To start or stop rollers
Note: After ready, if no activity is made within 30min after each use, the machine will
automatically switch into stand-by mode (Temperature will automatically reset to
176°F (80°C).
LOADING FILM
< Thermal Film Loading & Threading >
Loading Film
1. Remove the upper and lower film shafts from the
machine and load the films (do not tighten the core
screws at this time)
Figure 1
2. To load the top film, insert 1" core as shown on
Figure 1 (Note the direction that the film is wound)
3. Insert the shaft as shown in Figure 2.
Figure 2
4. Insert the core plug on the left hand side. (Figure 3)
Figure 3
5. Align and center the film and tighten the two core
screws. (Figure 4)
Figure 4
6. Repeat steps 2 through 4 to load the lower film.
(Please note the direction that the film is wound
for the bottom roll). (Figure 5)
Figure 5
7. Load the upper and lower film shafts on the machine.
* When loading 27" film on the lower, be sure to insert
the film core deeply into the film roll core to provide
room at each end.

8
THREADING FILM
Hot Film-Double Laminating
Caution: Hot Shoes and Heat Plates are extremely hot. Be careful not to touch the hot shoes or heat plates while
threading the film.
1. Turn the power switch on(“I” position).(The power switch is located on the right-hand side of the unit)
2. Push "TEMP." button to select appropriate temperature mode.
3. Complete the steps in the “Loading Film” section.
4. Remove the Front Feed Table.
5. Pull down the upper film over the Safety cover to the lower film; align and center the lower film to the upper film and
tighten the core screws.
6. Rewind the upper film until it aligns with the safety cover.
7. Take the safety cover off.
8. Then thread the lower film over the lower idle Bar until the film rests on the upper Heat shoe.(Before threading film,
Confirm the lower idle bar is in the location showing in the picture 1)
9. Push the idle bar up to the place showing in the picture 2. Then Put the Front Table back on.
10. Push "RUN/STOP" button to start rollers and thread the film using the laminating Threading Card(picture 3).
11. Put the safety cover back on.
Picture 1 Picture 2 Picture 3
Upper Roll Film
Lower Roll Film
Idle Bar
Idle Bar
Laminating Roller
Pull Roller
Adhesive Side
Glossy side
Glossy Side
Adhesive Side
Heat Plate
Heat Shoe-low
Heat Shoe-up

RSL-2700
9
MAINTENANCE
1. Do not apply any cleaning fluids to the rollers, certain fluids may cause damage.
2. Do not clean rollers with sharp objects, use a rubber gum eraser to clean resin off of the rollers.
3. Use a damp cloth with only water to clean the body of the machine.
4. Store machine in a dry clean area.
5.
Be careful, the safety cover may be hot.
TROUBLE SHOOTING GUIDE
Symptom Possible Cause Possible Solution
Rollers do not operate after the RUN/
STOP button is pressed
1. Power cord is not plugged in
2. Film is too tight for motor to start
1. Check the power cord
2. Adjust film tension by rotating
tension Bolt
Roller is not heating The hot shoes have not warmed up
completely yet Call your authorized dealer
Result of lamination is waved
1. Film tension is unbalanced
2. Lower idle bar is not located in
proper position
1. Adjust film tension by rotating
tension Bolt
2. Push idler bar up
Excessive noise while laminating 1. The tension may be set too tight
2. Temperature is too hot
1. Loosen the tension bolt
2. Change the temperature setting to
1.5Mil. Otherwise consult with the
customer service

10
SPECIFICATION
MODEL RSL-2700
Power supply AC120V . 220~240V , 50/60Hz
Power consumption 1450W
Max laminating width 27" (685mm)
Film thickness 38mic/1.5mil & 75mic /3.0mil
Paper thickness 80g~250g
Max laminating speed 1.4m/min
Ready time Approx. 10min.
Heating method Simple Hot Shoe Type
Temperature Control 2 Level
Driving motor DC geared
Max. Film Diameter ø265mm(up) ø120mm(low)
Speed control Fixed
Transport type 4 Roller
Film core size 1" (2.25" & 3" option)
Cross cutter No
Mounting thickness 0.4mm
Reverse Yes
Unit dimensions (w×d×h) 530×920×400mm
Carton dimensions (w×d×h) 736×1128×504mm