Royalcraft Aspen User manual

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 2 / 6
www.ro
y
alcraft.co.uk
Before you start
Warnings
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care
information.
Failure tofollow the warnings could result in serious injury.
Handle heavy parts with care.
Ensure that this product is fully assembled as illustrated before
use.
This product should only be used on firm, level ground.
The product contains small parts which could
pose a risk to young children. Keep small parts
out of reach of children.
Do not stand or climb onto this product.
This product is intended for domestic use only.
Ensure the product is always placed on level ground.
Furniture can be dangerous if incorrectly used. No liability will be
accepted for damage or injury caused by incorrect use of this
product.
This table is not intended to support a parasol separately. A
parasol base with suitable weight must be used to support
your parasol.
Dos
When you are ready to start, make sure that you have the right
tools, plenty of space and a clean, dry area for assembly.
Unwrap all packaging materials and place the components on
suitable surface to prevent scratching your product.
Check the pack and make sure you have all of the parts listed.
Check all screws and bolts are tightened and inspect regularly.
We recommend the use of furniture covers to protect your product
when not in use.
During bad weather or in winter months, the product should be
stored in a cool, dry place. Before storage, ensure that the product
is clean and dry.
To clean, wipe down with a sponge and warm soapy water and
wipe with a clean, drycloth.
When cleaning glass panels use a damp cloth or leather with
washing up liquid or soft soap if necessary.
Don’ts
Do not stand or climb onto the product.
Do not use power tools to construct this product.
Do not sit or lean onto the rims of this product.
Do not use this product if parts are missing, damaged or worn.
Never use scourers, abrasives or chemical cleaner.
Do not use this product as a ladder as this could lead tothe
product becoming unbalanced and overturning.
Do not place very hot or very cold items directly on the
glass surfaces unless adequately thick table-mats are used to
prevent such items from coming into contact with the glass.
Do not use the glass as a chopping surface.
Do not strike glass with hard or pointed items.
Do not use washing powders or any other substances containing
abrasives since these substances scratch the glass.
Dot use this product if the glass is chipped or broken.
Never drag furniture when moving it, always lift it.
Number of people required for assembly
Two people
Time to assemble
30 minutes
Tools required
Tips:
It is best not to fully tighten the nuts and
bolts until they are all correctly located.
Only carefully tighten them when you are
satisfied with the alignment of all
components.
Be careful not to overtighten.
Aspen 118cm/150cm Table
Assembly Instructions

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 3 / 6
www.ro
y
alcraft.co.uk
Components, fixtures & fittings (not actual size)
Parts List
Part
No. Diagram Qty. Part No. Diagram Qty.
A
Table Top
1 PC B
Upper Table Leg
1 PC
C
Bottom Table Leg
1 PC D
Glass Top
1 PC
W20
M6*20mm Bolt
8 PCS F3
Flat Washer
8 PCS
F2
Spring Washer
8 PCS G
Bolt Head Cap
8 PCS
S Spanner 1 PC
Aspen 118cm/150cm Table
Assembly Instructions

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 4 / 6
www.ro
y
alcraft.co.uk
Step by step assembly instructions
Step One
With the help of another person, open the cartons, place the Glass Top (D) onto a safe place
at first.
With the help of another person, place Table Top (A) upside down on a flat, non-abrasive
surface to avoid scratching the table surface or rim.
Step Two
With the help of another person, place Table Leg (C) onto the Table Leg (B).
BC
Aspen 118cm/150cm Table
Assembly Instructions

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 5 / 6
www.ro
y
alcraft.co.uk
Step Three
Locate the assembly position on the bottom side of the Table Top (A).
Attach the Table Legs (B) and (C) onto the assembly position, aligning holes in each part.
Loosely attach the Table Legs to the Table Top (A) using Flat Washers (F3), Spring Washers
(F2) and Bolts (W20).
Only tighten the bolts when all bolts and washers are in place and turn freely. Once you are
satisfied with the alignment of the components, carefully tighten all bolts using Spanner (S).
Do not over-tighten.
Cover each bolt with Bolt Head Cap (G).
Step Four
With the help of another person, stand the Table Frame in the upright position.
Carefully place the Glass Top (D) onto the Table Frame.
GF3
F2
W20
A
BC
D
Aspen 118cm/150cm Table
Assembly Instructions

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 6 / 6
www.ro
y
alcraft.co.uk
Step Five
With the help of another person, carefully turn over the table and place it in the upright
position. Level the table with the Adjustable Feet Screw on the bottom of the Table Legs.
Your table is now ready for use.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Adjustable Feet Screw
Aspen 118cm/150cm Table
Assembly Instructions