Safe Fleet Prime Design UXV 211 User manual

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2016 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
2
2
3
1
4
5
UXV-211 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
CONTENTS OVERVIEW
1—Rear Rotation Assembly................................... (Qty 1)
2—Front Rotation Assembly.................................. (Qty 1)

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2016 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
3
UXV-211 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
3—Rear Drive Shaft............................................... (Qty 1)
Right Hand, 50.00”
HKT-8102-Rotation Hardware Kit
Mounting Hardware
5—Front Drive Shaft .............................................. (Qty 1)
B Version, 35.75”
4—Connecting Bar................................................. (Qty 1)
48.00”
Anti-Seize (1X)
Lubricant (1X)
Clevis Pin (1X)Cotter Pin (1X)
M8 x 50MM (4X) ⅜" x 2.25" (2X)
1.00" Sealing
Stickers (10X)
M8 Lock Nut (4X) ⅜" Lock Nut (2X) ⅜" Flat Washer (4X)" Flat Washer (8X)
M8 Lock Nut (8X)
M8 x 30MM (8X)
Fender Washer (8X)Neoprene Washer (8X) " Seal Washer (8X)

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2016 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
4
UXV-211 ASSEMBLY INSTRUCTIONS–MOUNTING TO UTILITY BODY
M8 x 30MM Bolt
Sealing Washer
Mounting
Utility Body
Neoprene Washer
Fender Washer
M8 Locknut
Mounting Hardware (8X)
96.00”
84.00”
72.00”
96.00”
84.00”
72.00”
Rear Lower
Front Lower
3.50”3.50”
UTILITY BODY MOUNTING
6.00-8.00 Ft: Drill holes into the Service Body
mounting location according to dimensions shown.
0.1
0.4 Torque to 90 in-lbs
0.3
Using the fastening hardware shown below,
attach the vertical Uprights to the Utility Body.
The Neoprene Washer, Fender Washer, and
Locknut install from the inside of the Utility
Body in the order shown, while the Bolt and
Seal Washer install from the outside.
0.2 Position and align the vertical
Uprights until the mounting holes
realign to the body holes drilled
during Steps 0.1.

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2016 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
5
3
1
2/6
4
7
5
RIGHT ROTATION ASSEMBLY SEQUENCE
UXV-211 ASSEMBLY INSTRUCTIONS–RIGHT SIDE ROTATION
REAR DRIVE SHAFT
1.1
1.3
1.5
Torque to 90 in-lbs
1.4
1.2

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2016 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
6
UXV-211 ASSEMBLY INSTRUCTIONS–RIGHT SIDE ROTATION
CYLINDER HARDWARE CONNECTING BAR
2.1
2.2
3.1
3.2
CONNECTING BAR FASTENERSFRONT DRIVE SHAFT
5
4.4
Torque to 90 in-lbs
4.3
4.2
4.1

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2016 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
7
DRIVE SHAFT SEALING
Apply Silicone Sealant
to Connecting Bar ends
Adjust the Cylinder Flow
Control Screw to allow
approximately 3 seconds
time for the ladder to glide
down when operating the
loaded Ladder Rack.
6
CYLINDER ADJUSTMENT
7.1
7.2
UXV-211 ASSEMBLY INSTRUCTIONS–RIGHT SIDE ROTATION
For additional information regarding your UXV-211 Ladder Rack,
please visit the Prime Design website at: www.primedesign.net.
Using a QR code reader in your smart phone or tablet, read the QR
Code shown below and follow the same steps as you would from your
laptop or computer.
If you’re viewing this document as an interactive PDF, you may simply
click on the QR Code below to access the Prime Design website.
ADDITIONAL INFORMATION

USAM-UXV211-US01 Rev-B 1116