Safe Fleet Prime Design VBB3 PC11 User manual

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: i[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
2
2
1
3
Stiff Channel 78” (2X)
Anti-Seize (1X)
Mounting Mid-Foot (2X)Mounting Foot (4X) Foam Pad (6X) Channel Bracket (4X) M8 x 20MM (6X) M6 X 25MM (10X)
" Lock Washer (6X) " Flat Washer (22X)
M8 Lock Nut (6X)Sealing Washer (10X)
VBB3-PC11 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
1—FBM-0113 ........................................................ (Qty 1)
Channels with hardware
CONTENTS OVERVIEW
2—Crossbar Assembly........................................... (Qty 3)
3—Ladder Stop Assembly ..................................... (Qty 6)
1.75”
NOTE: This Manual contains Channels
and Hardware tting both two and three
Crossbar congurations.
If your model is a two Crossbar conguration,
disregard the extra Hardware contained in
the Channels and HKT-0166.

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
3
M8 Lock Nut
Flat Washer
Rear
Front
T Bolt Stud
3
4
2
1
Foam Pad
Mounting Bracket
M6 x 25MM Bolt
Sealing Washer
Rear
MPK-0093
Front
MPK-0092
MPK-0092
Flat Washer
VBB3-PC11 ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS
BASE ASSEMBLY SEQUENCE
MOUNTING BRACKETS
Install the Channel Mounting Brackets into the vehicle’s
roof mounting holes and torque to 60 in-lb.
1
CHANNELS
2.1 Apply Anti-Seize to all M8 T Bolt studs, then attach the
Channels to the Mounting Brackets using the indicated
hardware. Do not tighten until Step 2.2

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
4
Fig. A
Flush
Rear
Front
Fig. A
Rear
Front
Left
Right
M8 X 20MM
Lock Washer
Flat Washer
Left
Right
Rear
Front
Channel Rear Channel Front
(B) 48.00” (C) 24.00”
(A) 4.25”
VBB3-PC11 ASSEMBLY INSTRUCTIONS–BASE ASSEMBLY
2.2
Position the Channel ends
until contacting the End
Caps as shown in Figure A.
Torque all Mounting Bracket
Nuts to 90 in-lb
2.4
Loosen nuts
Position the rear Mounting
Brackets as shown.
Position the front and
mid Mounting Brackets
as shown.
Attach Mounting Brackets to the Aluminum
Strip Nuts located in the Channels
2.3
2.6 Position Mounting Brackets to designated dimension shown
below, then torque the M8 X 20MM bolt to 90 in-lbs. Proceed
to Step 3.1.

PRIME DESIGN, A SAFE FLEET BRAND ▪Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪Phone: [phone] ▪Toll Free: 1.8.PRIME.RACK ▪Fax: [phone] ▪Email: in[email protected] ▪Website: www.primedesign.net
TM & © 2018 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6764268, 6971563, 2364879, 8857689, 8511525, 8991889, 2271515, 2364897, 9506292, 9481313, 9481314, 9796340, 6202807, 6427889, 9415726 AND OTHER PATENTS PENDING
5
Rear
Front
Center
Front
Even Even
Even Even
Even Even
Rear
VBB3-PC11 ASSEMBLY INSTRUCTIONS–LADDER STOPS
CROSSBARS CROSSBAR ADJUSTMENT
3.1
Torque to
90 in-lbs
3.2
LADDER STOPS
4.2
Torque to 90 in-lbs
4.1
Loosen nuts

Page Intentionally Left Blank

Page Intentionally Left Blank

USAM-VBB3PC11-US01 Rev-B 0918