Safe Fleet Prime Dresign ASH-8034 User manual

WORKPRO LIGHT MOUNT
(BELOW CROSSBAR)
PRIME DESIGN, A SAFE FLEET BRAND
Address: 580 Opperman Drive, Eagan, MN 55123 ▪ Toll Free: 1.8.PRIME.RACK
Fax: [phone] ▪ Email: inf[email protected] ▪ Website: www.primedesign.net

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
2
ASH-8034 PACKAGING CONTENTS
CONTENTS OVERVIEW
ASH-8035 WorkPro Light Mount, Below Crossbar
NOTE: The Gen4 PBR Rack and
WorkPro LED Light shown in
this Manual are for illustrative
purposes only, and are not
included in this Kit.
M8 x 60MM (2X)
M8 x 25 MM (1X)
M8 Lock Nut (3X) " Flat Washer (3X) Nylon Washer (1X)
Bottom Connector (1X) Clamp Connector Pair (1X)

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
3
ASH-8034 ASSEMBLY INSTRUCTIONS
1–3
M8 Locknut
Bottom Connector
WorkPro Light Holder
M8 x 25MM Bolt
Nylon Washer
” Flat Washer
Bottom Connector
WORKPRO LIGHT MOUNT
INSTALLATION SEQUENCE
NOTE: The Gen4 PBR Rack and WorkPro LED
Light shown in this Manual are for illustrative
purposes only, and are not included in this Kit.
This Light Mount Kit contains only the parts
needed to repair, replace, or retrot one Light
Mount. Order an additional kit for the other to
add an additional accessory light.
1.1
1.2
Attach the Bottom Connector to the light holder as
shown below and torque to 90 in-lbs.
NOTE: With certain
WorPro models,
you may have to
move the light
holder in order to
install the M8 Bolt.
(Remove any
exisiting bolt
hardware from
the center hole)
Torque Bottom Connector Hardware to 90 in-lbs
BOTTOM CONNECTOR

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2021 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608, 10501022 AND OTHER PATENTS PENDING
4
M8 x 60MM
M8 Locknut
Clamp Connector
” Flat Washer
Fit as shown in Crossbar
and Connector Grooves
Install the WorkPro Light with the attached
Bottom Connector to the Crossbar and Clamp
Connectors using the hardware shown.
Finger-tighten only until step 3.
2
Torque Clamp Hardware to 90 in-lbs.
3.2
Adjust to desired positioning.
NOTE: If installing more that one WorkPro
Light and Mount, repeat Steps 1-2 and
position as needed.
3.1
ASH-8034 ASSEMBLY INSTRUCTIONS
USAM-ASH8034-US01 Rev-A 0219
MOUNTING LIGHT TO CROSSBAR ADJUSTMENTS
CONTENTS OVERVIEW