SAFE HOME HTZSAFE 805A+MC User manual

Wireless Alarm System
User Manual

1
1. Configuration List
2. System Components And Usage
Plug-in Alarm Receiver
Plug-in Alarm Receiver 1 piece
Note:The alarm system has been programmed already,
please operate the system according to the part 3 of
the manual;
Power Plug:plug the receiver into a socket
Volume
Melody
Indicator Light
Power Plug
Wireless Door/Window Sensor
Installation Accessories 1 set (double side tape)
Manual 1 piece
If you want to add additional HTZSAFE detectors
to the system,please operate the system according to
the part 4 of the manual or contact us directly.
1 piece(
)
includes 2 pieces
AAA 1.5V batteries
Volume: 4 volume levels adjustable
Melody: 35 classic melodies optional
Indicator Light: flash for several seconds when the sensor
be activated

2
Wireless Door/Window Sensor
Sensor’s Body: emit the alarm signal,door/window
opening detected through the separation of the sensor ’s body
and the magnet.
Magnet: a part of the door/window sensor,work with
the sensor’s body.
Indicator Light: flash once each time the sensor be
activated; flash all the time if the low battery warning.
Speaker
Sensor’s Body
Indicator Light
Speaker:sound for several seconds when the sensor
be activated
Magnet

3
3. Operation Instructions
Step2
Activate the wireless door/window sensor
(separate the sensor’s body and the magnet)
The indicator light of the sensor
will flash once if the sensor be
activated
Step 1
Plug the receiver into a outlet
The indicator light of the receiver
will flash for 15 seconds means
working properly
Battery Compartment
Reed Switch
Reed Switch:will be activated by separating
the sensor’s body and the magnet
Battery Compartment: 2 pieces AAA 1.5V batteries( included)
+
-+
-

4
Step 3
Press “Melody” once to choose the melody for this sensor,
total 35 melodies optional.
Melody
Step 4
Installation(wireless door/window sensor)

5
4. Other Settings
(1)How to add additional sensors to the receiver
(up to 32 sensors can be added to 1 receiver)
Step 1
Plug the receiver into a outlet
(1)pry open the back cover by a screwdriver
(2)replace the batteries(2pcs AAA 1.5V batteries,please
note the anode and cathode)
(3)put the back cover at the correct position
(as the picture), and then push it back.
(1)
+
-+
-
(2) (3)
How to replace the batteries
max. 8mm
Note:
the gap between the sensor's body and the magnet
is maximum 8mm

6
Step 2
Press and hold the “Volume” button for 5 seconds and release
the button when you heard a beep prompt and the indicator
light flashing;
Step 3
Activate the sensor
Note:please make the sensor close to the receiver
Volume
light up
press and hold the button
for 5 seconds
Volume
flashing slowly
release the button
Volume

7
Step4
Activate the sensor again to confirm the sensor has been
added to the receiver already.
(a ring tone prompt and the
indicator light flashing quickly
means the sensor has been added
to the wireless alarm receiver
successfully)
(
the indicator light
flashing once means the sensor
was activated properly)
separate the sensor’s body and
the magnet,
flashing quickly
(1)If the extra wireless door/window sensor,
please activate the sensor as below:
(2)If the other extra sensor,take the solar motion
sensor(HB-T704) for example,please activate
the sensor as below:
(a ring tone prompt and
the indicator light flashing
quickly means the sensor
has been added to the
wireless alarm receiver
successfully)
flashing quickly
ON/OFF
( twice)press
(make sure the sensor has
been turned on already,and
then press the ON/OFF button
twice to activate the sensor--the
light of the ON/OFF button will
flash once means the sensor
was activated properly)

8
(2)How to delete the sensors of the receiver
Step 1
Plug the receiver into a outlet
Step 2
Press and hold both the “Volume” button and “Melody” button
for 10 secondsand release the buttons when you heard a long
beep prompt;
Note: all the sensors will be deleted by this operation.
(3)How to adjust the alarm volume
Step 1
Plug the receiver into a outlet
Step 5
Press”Melody”button to choose the melody for this sensor.
total 35 melodies optional.
Volume
Melody

9
Step 2
Press the “Volume” once to adjust the volume of
the receiver. (total 4 volume levels adjustable)
(4)How to change the melody for the sensors
Step 1
Plug the receiver into a outlet
Same steps for other sensors which have been added to
the receiver already.
Step 2
Activate the sensor first,and then press the “Melody” button
to choose the melody for this sensor
Volume
(total 35 melodies optional,match different melody
with different sensor)

10
5. Technical Parameters
Plug-in Alarm Receiver
Technical parameters
Static Current 20mA; Alarming Current 300mA
Working Current
AC 110V-220V
433MHz FSK+FHSS
Technical Parameters
Working Voltage
Wireless Frequency
Item
80mm 48mm
86mm
34mm

Wireless Door/Window Sensor
29mm
90mm
Item
Wireless Transmission Range
Wireless Frequency
Working Voltage
Battery Type
433MHz FSK+FHSS
2PCS AAA 1.5V Battery
3.0V
Technical Parameters
Technical parameters
Working Current Static 0.1 ; Alarming 60mA< <mA
Working Temperature Range
600Feet
-10℃ to 55℃
84mm
11mm 15mm 9mm
22-HB201905-805A(1.1)MC-2(1.1)-02
11
After-sale Service:
E-mail:[email protected]