Salford I-5100 19 User manual

I-5100 12’, 19’, 22’, 25’, 29’Assembly & Parts Manual 2016
Manual #: MNPI-51-1229-16A

Table of Contents
General Information
Serial Number and Paint Code.....................................................................................................................4
Salford Recommended Torque Values.........................................................................................................5
Wheel Torque Specications .......................................................................................................................6
Tire Pressure Ratings ...................................................................................................................................7
General Safety Precautions..........................................................................................................................8
Cylinder Series Identication Guide..........................................................................................................10
Decal Locations .........................................................................................................................................12
FrameWing Fold Cylinder Installation ................................................................................................................16
Frame Assembly.........................................................................................................................................18
Spider Link Install......................................................................................................................................20
Tongue Mount Install.................................................................................................................................22
Front Tripod Assembly ..............................................................................................................................24
Hydraulic Tilt Adjust Tongue Installation..................................................................................................26
Hydraulic Tongue Hose Routing................................................................................................................29
Telescope Mount Hose Holder...................................................................................................................30
Axles 12ft Wheel andAxle Layout......................................................................................................................31
19ft Wheel andAxle Layout......................................................................................................................32
22ft - 29ft Wheel andAxle Layout............................................................................................................33
Mainframe Axle Installation......................................................................................................................34
Wing Axle Installation ...............................................................................................................................36
Gauge Wheel Installation...........................................................................................................................38
12000LB Hub and Spindle Assembly........................................................................................................40
8000LB Hub and Spindle Assembly..........................................................................................................42
4,000LB & 5,000LB Hub and Spindle Assembly......................................................................................44
Coulter Assembly
Double Angle Concave Blade Assembly...................................................................................................46
Single Angle Concave Blade Assembly.....................................................................................................48
Wavy Coulter Assembly.............................................................................................................................50
Guide Coulter Shim Installation ................................................................................................................52
Inverted Hub Assembly..............................................................................................................................54
5 Bolt Coulter Hub Assembly....................................................................................................................56
Coulter Layouts
12ft Blade and Coulter Layout...................................................................................................................58
19ft Blade and Coulter Layout...................................................................................................................59
22ft Blade and Coulter Layout...................................................................................................................60
25ft Blade and Coulter Layout...................................................................................................................61
29ft Blade and Coulter Layout...................................................................................................................62
Lights & Hydraulics
12ft Axle Lift Hydraulics...........................................................................................................................64
19 - 29ft Axle Lift Hydraulics....................................................................................................................66
Wing Fold Hydraulics................................................................................................................................68
Lights & SMV Installation.........................................................................................................................70
Tow Hitch (Optional)
Tow Hitch Installation................................................................................................................................72
Tow Hitch Hydraulics................................................................................................................................74
Tow Hitch Dual Remote Hyd. Assembly & 7 Pin Plug Assembly............................................................75
Salford Group Inc.
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016
Feb-09-2016

Notes
Salford Group Inc.
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016
Feb-09-2016

Serial Number and Paint Code

Your machine has a model and serial number to
clearly identify it. Always give your dealer the
model number and serial number of your
machine when ordering parts or requesting
service information. Record the model and serial
numbers in the spaces provided for easy
reference. We also recommend recording the
serial numbers of any third party equipment,
such as fans, conveyor, etc.
Model number:
Serial numbers:
ATTENTION: If your machine has the decal shown below located next to the serial
number plate, the red paint code is EF20824P1. If your machine does NOT have the
decal shown below, the red paint code is EF25521P1.
Serialnumberlocationpicture
General Information
Salford Group Inc.
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016
Feb-09-2016

6$/)25' 5(&200(1'(' 72548( 9$/8(6
BOLT SIZE GRADE 2 GRADE 5 GRADE 8
ft-lbs Nm ft-lbs Nm ft-lbs Nm
1/2"NC 50 68 75 102 105 142
5/8"NC 90 122 150 203 210 285
3/4"NC 160 217 270 366 375 508
7/8"NC 145 197 395 536 610 827
1"NC 210 285 590 800 910 1234
127(6: These recommended torque values are applicable when applied to the nut
only. These recommended torque values are approximate only. The torque-tension
relationship is affected by lubrication, surface finish, thread fit, plating, lock-washers, etc.
'2 127 use these values if a different torque value or tightening procedure is given for
a specific application. Torque values listed are for general use only. Check tightness of
fasteners periodically.
Shear bolts are designed to fail under predetermined loads. Always replace shear bolts
with identical grade.
Fasteners should be replaced with the same or higher grade. If higher-grade fasteners
are used, these should only be tightened to the strength of the original.
Make sure fasteners threads are clean and that you properly start thread engagement.
This will prevent them from failing when tightening.
WARNING Both sides of the u-bolt
Do not tighten one side of the must be tightened equally.
u-bolt before the other side.
Salford Recommended Torque Values
Feb-09-2016 Page 5
Salford Group Inc.
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016

WARNING
Maintain proper torque to provide safe and secure
attachment of the wheel hub/drum. Improperly tightened
wheel nuts can cause the wheel to separate from the wheel mounting surface
during operation. This could result in property damage, serious personal injury,
or possibly loss of life.
NOTE - If wheel does not have chamfers to match profile of the nuts, use flat side of
nuts against rim face.
Install all lug nuts/bolts by hand to prevent cross threading and tighten lug nuts/bolts
following the steps and tightening sequence diagram below.
NOTE - Recheck the torque settings of lug nuts/bolts after 10km (6 miles) and again
after 50km (30 miles). Periodically and at the beginning of each season check the
condition and the torque of the lug nuts/bolts.
5
3 6
4
1
2 2
1
4
6
3
5
7
8
5
67
1
2
3 10
8
49
6 LUG BOLT PATTERN 8 LUG BOLT PATTERN 10 LUG BOLT PATTERN
Lug Nut/Bolt Tightening Sequence
*'Dry Torque' values shown.
If using a lubricant (eg oil, or anti-sieze), use only 75% of the dry torque.
STEP 1) Torque to 20-25 ft•lbs following the appropriate pattern below.
STEP 2) Torque to 55-60 ft•lbs following the appropriate pattern below.
STEP 3) Torque to final ft•lbs rating (see bolt size below) following the
appropriate pattern below.
Bolt Size (Hub Size) Final Torque*
1/2" dia. bolt (up to 3000 lb hubs) 90 ft•lbs
9/16" dia. bolt (4000 - 5000 lb hubs) 120 ft•lbs
5/8" dia. bolt (5500 - 12000 lb hubs) 170 ft•lbs
3/4" dia. bolt (16000 - 20000 lb hubs) 300 ft•lbs
7/8" dia. bolt (25000 lb hubs) 540 ft•lbs
22mm dia. bolt (35000 lb hubs) 540 ft•lbs
Wheel Torque Specications
Salford Group Inc.
Page 6
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016
Feb-09-2016

N
N
Deep dish
11L
245
425
445
Tires to install
deep dish in:
N
N
Deep Dish
12.5L
305
15 x 19.5
340
Tires to install
deep dish out:
If bolts/nuts are coned, ensure
proper seating in chamfer on rim.
Ensure proper inflation of each tire for safe operation and extended tire life.
NOTE - Periodically and at the beginning of each season check the condition and the
pressure of each tire.
Tire Installation Direction
Do not rely on valve stem for orientation of
tires. It may face in or out on different rims.
Measure both sides of tire in to rim face. Install the
deep side in or out according to the instructions below.
Tire Size Pressure [psi] Pressure [bar]
23.1 x 26 (16 ply) 25 [psi] 1.72 [bar]
15 x 19.5 Lug Tire (6 ply) 30 [psi] 2.07 [bar]
Load Range C - 11L15 35 [psi] 2.41 [bar]
28L26 (16 ply) 36 [psi] 2.48 [bar]
30.5LR32 (181A8/B) 52 [psi] 3.58 [bar]
Load Range D - 11L15
- 12.5L15
65 [psi] 4.48 [bar]
15 x 19.5 Lug Tire (14 ply) 70 [psi] 4.83 [bar]
340/60R16.5IMP (145A8/B) 73 [psi] 5.00 [bar]
Load Range F - 11L15
- 12.5L15
Truck Tires - 245/70R19-5
- 305/70R22-5
90 [psi] 6.20 [bar]
Truck Tires - 425/60R22-5 110 [psi] 7.49 [bar]
Truck Tires - 445/60R22-5 SEE TIRE SIDEWALL!!
Tire Pressure Ratings
Feb-09-2016 Page 7
Salford Group Inc.
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016


Signal Words
The words DANGER, WARNING, or CAUTION are used with the safety alert symbol. Learn to
recognize the safety alerts, and follow the recommended precautions and safe practices.
Three words are used in conjunction with the safety-alert symbol:
DANGER Indicates an imminently hazardous situation that, if not
avoided, will cause DEATH OR VERY SERIOUS INJURY
WARNING Indicates a potentially hazardous situation that, if not
avoided, could cause DEATH OR SERIOUS INJURY
CAUTION Indicates a potentially hazardous situation that, if not
avoided, may cause MINOR OR MODERATE INJURY
Replace any DANGER, WARNING, CAUTION, or instructional decal that is not readable or is
missing. The location and part number of these decals are identified later in this manual.
The words Important and Note are not related to personal safety but are used to give additional
information and tips for operating or servicing this equipment.
IMPORTANT: Identifies special instructions or procedures which, if not strictly observed could
result in damage to, or destruction of the machine, process or its surroundings.
NOTE: Indicates points of particular interest for more efficient and convenient repair or
operation.
A CAREFUL OPERATOR IS THE BEST INSURANCE AGAINST AN ACCIDENT!
 
General Safety Precautions
Salford Group Inc.
Page 8
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016
Feb-09-2016

Wing Fold
Wings may fall rapidly causing
injury.
Do not stand under wings.
Always stay clear of wings when
being lowered, raised, or in an
elevated state.
Always use wing locks when
raised.
Ensure cylinders are completely
filled with hydraulic fluid to avoid
any unexpected movement.
Hydraulics
DO NOT search for high pressure
hydraulic leaks without any hand and
face protection. A tiny, almost
invisible leak can penetrate skin,
requiring immediate medical
attention.
Use cardboard or wood to
detect leaks – never your hand.
Double check that all is clear
before operating hydraulics.
NEVER remove hydraulic hoses
or ends with machine elevated.
Relieve hydraulic pressure before disconnecting hydraulic hoses or ends.
Use transport/maintenance locks when machine is raised.
Maintain proper hydraulic fluid levels.
Keep all connectors clean for positive connections.
Ensure all fittings and hoses are in good condition and are properly tightened.
NEVER work on or under an elevated machine unless it has been locked up
using the transport/maintenance locks.
DANGER 
DANGER 
General Safety Precautions
Feb-09-2016 Page 9
Salford Group Inc.
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016

Cylinder Series Identication Guide
CROSS TUBE STYLE ROD ENDS
WELDED TO ROD
PORTS MACHINED IN GLAND
AND ENDCAP
PART NO. STAMP
FORGED END-CAPS
WELDED TO BARREL
TIE-ROD STYLE BODY
PART NO. LABEL
WELDED CAP BYPASS
PORT - HRC XXXX ONLY
SET SCREW
FOR PORT POSITION
ADJUSTMENT
FORGED CLEVIS STYLE ROD
ENDS WELDED TO ROD
*REQUIRED 3 3/8" LONG OR LONGER PINS
BALL JOINT ENDS
GREASE ZERK
SET SCREW
FOR PORT POSITION
ADJUSTMENT
PART NO. LABEL
SALFORD 'C' SERIES
HC XXXX AND HCR XXXX
( MANUFACTURER PART NO. XX T XXX - XXX)
SALFORD 'B' SERIES*
HS XXXX B AND HSR XXXX B
(MANUFACTURER PART NO. SF XXXXXX )
SALFORD 'BBJ' SERIES
HS XXXX BBJ AND HSR XXXX BBJ
( MANUFACTURER PART NO. HSRXXXXBBJ)
Salford Group Inc.
Page 10
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016
Feb-09-2016

THIS PAGE INTENTIONALLY LEFT BLANK
Feb-09-2016 Page 11
Salford Group Inc.
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016

Decal Locations
65
4
3
2
1 1
2
3
3
3
3
3
33
3
INSTALL
BEFORE
MOUNTING
HEADS
3
INSTALL BEFORE MOUNTING HEADS
NOT
ON 16'
NOT ON 16'
NOT ON 12'
NOT
ON 12'
33
NOT ON 12'
NOT
ON 12'
Unless noted otherwise,
install decals after all
coulters and/or shanks are
installed to avoid covering
them up.
16' ONLY16' ONLY
Salford Group Inc.
Page 12
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016
Feb-09-2016

Decal Locations
16
17
19
FRONT VIEW OF WING HINGE
15
ALIGN DECAL SO ARROW POINTS DOWN WHEN WINGS FOLDED
13 12
13 12
8
9
14 14
7
18 15
11
10
1414
10
11
15 18
20
21
NOT ON 12'/16'
11
11
18
22
18
18
18
18
Install decal after all coulters and/or shanks are installed to avoid covering them up
NOT ON 12'/16'
NOT
ON 12'/16'
Feb-09-2016 Page 13
Salford Group Inc.
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016

Decal Locations
ITEM
I-5100
12ft
I-5100
16ft
I-5100
19ft-29ft
PART
NUMBER
DESCRIPTION
1 2 2 2 GD102 WWW. SALFORD DECAL
2 2 2 2 GD229 I-5100 DECAL
3 6 10 10 GD100
SALFORD DECAL LARGE w/BLACK BORDER
(4'' HIGH X 16'' LONG)
4 1 1 1 GD109 DEPTH CONTROL DECAL
5 1 1 1 GD110 WARNING DON'T LIFT DECAL
6 1 1 1 GD245 ATTENTION LUBRICATE DECAL
7 1 1 1 GD214 2 1/2" x 2 1/2" PATENT NUMBER & PATENT PENDING DECAL
8 1 1 1 GDSW116 IMPORTANT - DO NOT EXCEED THE MAXIMUM TILT
9 1 1 1 GDSW117 IMPORTANT - AVOID EXCESSIVE DEPTH AND COULTER WHIP
10 2 2 2 GD194
8 LUG TIGHTENING SEQUENCE & TIRE PRESSURE WARNING
STICKER
11 - - 4 GD193
6 LUG TIGHTENING SEQUENCE & TIRE PRESSURE WARNING
STICKER
12 2 2 2 GDSW2 USE PROPER TOOLS AND READ MANUAL DECAL
13 2 2 2 GDT3
DANGER STICKER FOR CRUSHING HAZARD "HITCHING IMPLEMENT
TO TRACTOR PINCH POINT"
14 - 4 4 GDSW200
WARNING STICKER OVERHEAD CRUSHING HAZARD "SHOWS
WING FALLING ON SOMEONES HEAD"
15 - - 2 GD144 WING LOCK DECAL - 570
16 1 1 1 GDSW700
WARNING STICKER, ALTERNATE HIGH PRESSURE FLUID HAZARD
STICKER
17 1 1 1 GDSW4 SAFE OPERATION LIST DECAL
18 3 7 9 GD108100 GREASE EVERY 100 HOURS DECAL
19 1 1 1 GD210 HOSE IDENTIFICATION DECAL
20 1 1 1 GD212 TURNBUCKLE DIRECTION DECAL
21 1 1 1 GD249 5100 OPERATING RECOMMENDATIONS DECAL
22 1 1 1 ---- SERIAL NUMBER PLATE
Salford Group Inc.
Page 14
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016
Feb-09-2016

Decal Locations
GD229
GD210
18
19
13
12
15
17
14
11
9
10
8
456
3
2
1
GDSW4
GD108100
GD144
GDSW2
GDSW200
GDT3
GD194
GDSW117
GD193
GD214
GDSW116
GD245
GD109 GD110
GD100
GD102
7
16
GDSW700
20
GD212
GD249
21
22
SERIAL #
PLATE
Feb-09-2016 Page 15
Salford Group Inc.
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016

REFER TO HYDRAULIC
LAYOUT FOR CYLINDER SIZES
15
4
13
14
8
9
2
1
16
3
7
12
11
10
INSTALL CYLINDERS WITH
PORTS FACING THE
CENTER OF THE MACHINE
5
6
CAUTION
When installing pins, washers must be
installed, major damage and or serious
injuries or death may occur if washers
are not installed properly
17
Wing Fold Cylinder Installation
Frame
Salford Group Inc.
Page 16
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016
Feb-09-2016

CAUTION
!!! DO NOT install pins in rods ends until ALL AIR has been purged out of the
wing folding hydraulic circuit. See hydraulic layout for instructions.
When installing pins, washers must be installed, major damage and or
serious injuries or death may occur if washers are not installed.
See * Cylinder Series Identification Guide* page for details on
types of wingfold cylinders
ITEM QTY PART NO.
DESCRIPTION
1 1 A60079F HYDRAULIC MANIFOLD BRACKET
2 1 H00012 3 SECTION WING FOLDING MANIFOLD
3 4 GPH2000612A06 1 1/4" x 6 1/2" HARDENED PIN - 2 HOLES
4 4 GPHF2000312H05 1 1/4" x 3 1/2" SHOULDER PIN HARDENED W/ FLATS
5 1 GP1600414C04 1" x 4 1/4" RING & WASHER PIN
6 1 GHP9 #9 HAIR PIN
7 8 BF20S 1 1/4" SAE WASHER
8 2 BN10L 5/8" NYLOCK NUT NC
9 2 BN06L 3/8"-16NC NYLOCK NUT
10 2 FL01061 RTS WING LOCK LUG
11 4 BN08L 1/2" NYLOCK NUT NC
12 4 B0820 1/2" NC x 2" LG. HEX BOLT GR. 5
13 2 B1020 5/8 X 2" BOLT GR. 5 PLATED
14 2 B0625 3/8" NC x 2 1/2" LG. HEX BOLT GR. 5
15 4 BSC0520 5/16" x 2" COTTER PIN
16 8 BSC0620 3/8" x 2" COTTER PIN
17 4 GF1688 1/8" NPT GREASE FITTING 45deg
Wing Fold Cylinder Installation
Feb-09-2016 Page 17
Salford Group Inc.
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016

Frame Assembly
43
29' WING SHOWN
22' WING SHOWN
29
10
10
25' FRAME ONLY
44
11
7
14 36
22
11 34
42
21
* NOTE: RED LOCTITE REQUIRED ON
1
*
25' FRAME ONLY
9
45 2911
18
3
17
50
10
11
11
46
NOTE : 2 DIFFERENT FRAME BRACES
40 8 1
37
38
35 6
10
4 714
37 1 8 3938
37 1
8
3938
13 541
12' ONLY
*
11
10
10 10 1211 31 4
*
Salford Group Inc.
Page 18
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016
Feb-09-2016

Frame Assembly
29' WING
22' WING
19' WING NOT SHOWN
FRAME MAY INCLUDE C11323 FRAME BRACES OR C11778,C11779 FRAME BRACES
ITEM 12ft 19ft 22ft 25ft. 29ft PART NO. DESCRIPTION
1 - 6 6 6 6 B1015 5/8" NC x 1 1/2" LG. HEX BOLT GR. 5
2 --- 30 - B1020 5/8"NC x 2" LG. HEX BOLT
3 4 4 4 4 4 B1225 3/4"NC x 2-1/2" HEX BOLT
4 20 20 20 20 20 B1230 3/4"NC x 3" BOLT GR. 5
5 8 - - - - B1255 3/4" x 5 1/2" HEX BOLT
6 8 - - - 16 B1260 3/4" NC x 6" LG. HEX BOLT GR.5
7 16 16 16 16 24 BF12HS 3/4" HARD STRUCTURAL WASHER
8 - 6 6 6 6 BL10 5/8" LOCKWASHER
9 - - 40 70 40 BN10L 5/8" NYLOCK NUT NC
10 52 60 76 92 92 BN12L 3/4" NC NYLOCK NUT
11 4 18 22 30 22 BU1260 3/4" x 6 x 6" U-BOLT
12 2 2 2 2 2 BU1266 U-BOLT 3/4" x 6" x 8" LG.
13 2 - - - - C11186 4" x 6" x 16" BOLT ON TOOLSTUB - 3/4" U-BOLTS
14 2 2 2 2 4 C11199 I-5100 2" DROP 11"LG GUIDE COULTER STUB
15 - 1 --- C11770L 19FT I-5100 WING FRAME - LEFT
16 - 1 --- C11770R 19FT I-5100 WING FRAME - RIGHT
17 1 1 1 1 1 C11319 5100 TONGUE TRIPOD TOWER
18 - 1 --- C11409L 5119 FRONT WING FRAME - LH
19 - 1 --- C11409R 5119 FRONT WING FRAME - RH
20 - 1 1 1 1 C11412 5100 12', 19', 22', & 29' MAINFRAME
21 - 1 --- C11414 5100 CENTER FRONT FRAME - FOR CONTAINER
22 - - 111 C11307 5122, 5129 FRONT MAIN FRAME
23 - - - - 1 C11465L 29FT I-5100 WING FRAME - LEFT
24 - - - - 1 C11465R 5129 CONTAINER WING FRAME
25 - - - - 1 C11466L 5129 FRONT WING FRAME - LEFT
26 - - - - 1 C11466R 5129 FRONT WING FRAME - RIGHT
27 - - 1 1 - C11582L 5122 FRONT WING FRAME - LEFT
28 - - 1 1 - C11582R 5122 FRONT WING FRAME - RIGHT
29 - - 1 1 - C11583L 22FT I-5100 WING FRAME - LEFT
30 - - 1 1 - C11583R 22FT I-5100 WING FRAME - RIGHT
31 2 2 2 2 2 C11586 5100 12, 19-29' CENTER BLADE ADJUSTABLE STUB
32 1 - - - - C11589 12' 5100 MAIN FRAME
33 1 - - - - C11590 12' 5100 FRONT MAIN FRAME
34 --- 2 - C11592 I5125 FRONT WING EXTENSION
35 4 - - - 8 FL00943 1" x 2" 44w PULL-UP PLATE
36 4 4 4 4 8 FL04207 5100 STABILIZER COULTER SHIM
37 - 12 12 12 12 GBB175150100 1 3/4" x 1 1/2" x 1" LG. HARD BUSHING
38 - 6 6 6 6 GF1610 1/8" NPT GREASE FITTING
39 - 4 4 4 4 GPH2400814F 1 1/2" x 8 1/4" LG. HARD PLATE PIN
40 - 2 2 2 2 GPH2401000F 1 1/2" x 10 7/8" LG. AXLE PIN - HARDENED
41 2 - - - - L00520 5/8" x 7" x 8 1/2" - 3/4" U-BOLT PLATE
42 - - 222 C11778 5100 OUTER WING BRACE
43 - - 444 A60208 BLACK PLASTIC CAP FOR 4" x 4" TUBE
44 - - 444 BU1046 U-BOLT 5/8" x 4" x 7 1/2" LG.
45 --- 2 - C11773 I-5100 25' REAR WING EXTENSION
46 - - 888 B1265 3/4"NC x 6 1/2" LG. HEX BOLT GR. 5
47 - - 888 BU1040 5/8 x 4 x 5-1/2" U-BOLT
48 - - 888 BU1061 U-BOLT 5/8" x 6" x 5 1/2"
49 - - 8 8 8
C11779 5100-25' 29' WING BRACE MOUNT
50 - - 111 C11323R 5129 OUTER WING BRACE - RIGHT
51 - - 111 C11323L 5129 OUTER WING BRACE - LEFT
Feb-09-2016 Page 19
Salford Group Inc.
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016

Spider Link Install
3
6
7
8
12
14
17
16
4
2
9
8
76
8
7
6
16
11
5
12 14
17
NOTE:
LEAVE BOLTS
LOOSE UNTIL SPIDER IS PINNED IN PLACE
10 13 15
SEE
FRONT FRAME & WING
ASSEMBLIES
FOR ASSEMBLY
INSTRUCTIONS FOR HINGE PINS
SEE
FRONT TRIPOD ASSEMBLY
FOR ASSEMBLY INSTRUCTIONS
1
5
22' & 29' FRAMES ONLY
ENSURE BOTH
4
ARE
EQUAL DISTANCE FROM FRONT
BEAM OF FRAME
3 3/4" 3 3/4"
Salford Group Inc.
Page 20
MNPI-51-1229-16A I-5100 12', 19', 22', 25', 29' Assembly and Parts Manual 2016
Feb-09-2016