Satel Integra 128-WRL User guide

SATEL sp. z o.o.
ul. Schuberta 79
80-172 Gdańsk
POLAND
tel. + 48 58 320 94 00
[email protected]
www.satel.eu
integra-wrl_i_en 12/12
Alarm Control Panels
INTEGRA 128-WRL
Firmware version 1.11
INSTALLER
MANUAL

WARNINGS
The security alarm system should be installed by qualified personnel.
Prior to installation, please read carefully this manual in order to avoid mistakes that can lead
to malfunction or even damage to the equipment.
Disconnect power before making any electrical connections.
Changes, modifications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
The SATEL's goal is to continually upgrade the quality of its products, which may result in
alterations of their technical specifications and firmware. The current information on
the introduced modifications is available on our website.
Please visit us:
http://www.satel.eu
Hereby, SATEL sp. z o.o., declares that this control panel is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC. The
declaration of conformity may be consulted at www.satel.eu/ce
The following symbols may be used in this manual:
- note;
- caution.

CONTENTS
1. General.............................................................................................................................2
2. Features ...........................................................................................................................2
3. Keypads............................................................................................................................4
3.1 Features of keypads with mechanical keys ...............................................................5
4. Expansion modules ..........................................................................................................5
4.1 Modules to be connected to the keypad bus .............................................................5
4.2 Modules to be connected to the expander bus...........................................................5
4.3 Wireless devices supported by the controller ............................................................8
5. System installation............................................................................................................8
5.1 Installation plan..........................................................................................................8
5.2 Estimation of the system current consumption..........................................................9
5.3 Cabling ......................................................................................................................9
5.4 Installation of control panel mainboard......................................................................9
5.4.1 Description of the mainboard............................................................................11
5.5 Connecting devices to the keypad bus....................................................................12
5.5.1 Addressing devices connected to the keypad bus............................................13
5.5.2 Numeration of keypad zones............................................................................14
5.5.3 Connecting computer to the keypad RS-232 port.............................................14
5.6 Connecting devices to the expander bus.................................................................15
5.6.1 Connecting the INT-VG module or CA-64 SM expander..................................16
5.6.2 Addressing devices connected to the expander bus........................................16
5.7 Connecting the detectors.........................................................................................16
5.7.1 End-of-line resistors .........................................................................................17
5.8 Connecting the sirens..............................................................................................17
5.9 Connecting power supply ........................................................................................18
5.9.1 Main power supply ...........................................................................................18
5.9.2 Backup power supply .......................................................................................18
5.9.3 Control panel power-up / start-up procedure....................................................19
5.10 First start-up of the control panel.............................................................................19
5.11 Emergency procedure of the control panel start-up.................................................20
5.12 GSM telephone start-up ..........................................................................................21
5.13 Installation of wireless devices ................................................................................22
5.13.1 Adding new wireless devices............................................................................23
5.13.2 Removing wireless devices..............................................................................25
5.14 Connecting computer to the control panel...............................................................25
5.15 Connecting the external modem..............................................................................26
5.15.1 Configuring settings of the modem to be connected to control panel...............27
5.16 Connecting the printer.............................................................................................28
6. Numeration of zones and outputs in the system.............................................................29
7. Specifications .................................................................................................................30
7.1 Control panel...........................................................................................................30
7.2 INT-KLCD keypad ...................................................................................................31
7.3 INT-KLCDR keypad.................................................................................................31
7.4 INT-KLCDL keypad .................................................................................................31
7.5 INT-KLCDS keypad.................................................................................................31
7.6 INT-KLCDK keypad.................................................................................................32

2 Installer Manual SATEL
1. General
This manual applies to the INTEGRA 128-WRL control panel. The manual also describes
keypads compatible with the control panel and other devices that may be included in the
security alarm system.
The INTEGRA 128-WRL control panels meet the requirements of the following standards:
– EN 50131-1 Grade 2;
– EN 50131-3 Grade 2;
– EN 50131-6 Grade 2;
– EN 50130-4;
– EN 50130-5 Class II.
2. Features
System structure
•32 partitions.
•8 objects (subsystems).
Zones
•8 programmable hardwired zones on the control panel mainboard:
– support for NO and NC type detectors, as well as roller shutter and vibration detectors;
– support for Single EOL and Double EOL configuration;
– programmable value of end-of-line resistors;
– several dozen zone types.
•Maximum number of programmable zones: 128.
Outputs
•8 programmable hardwired outputs on the control panel mainboard:
– 2 high-current outputs;
– 6 low-current outputs, OC type;
– over 100 functions;
– execution of custom control functions due to the possibility of programming complex
logic operations on the outputs.
•Maximum number of programmable outputs: 128.
•3 high-current outputs on the control panel mainboard with power supply output
functionality.
Communication buses
•Keypad bus for connecting up to 8 devices.
•Expander bus for connecting up to 32 devices.
Wireless devices
•Integrated wireless interface of the ABAX system to allow operation of:
– up to 48 wireless devices;
– up to 248 APT-100 keyfobs.
•Two-way encrypted radio communication in the 868 MHz frequency band

SATEL INTEGRA 128-WRL 3
Communication
•Telephone dialer (communicator) GSM/GPRS to allow:
– events reporting;
– event messaging;
– checking the alarm system status by telephone (DTMF or SMS);
– remote control of the alarm system outputs by telephone (DTMF);
– remote control of the alarm system using SMS messages.
•Built-in GSM modem to allow remote operation and programming of the alarm system
(300 bps or CSD transmission).
•Reporting events to two monitoring stations:
– several communication formats (including Contact ID and SIA);
– 4 telephone numbers (2 main + 2 backup ones);
– 9 identifiers.
•Several ways to send event codes to the monitoring station:
– GPRS transmissions (encrypted),
– SMS messages,
– GSM voice link.
•Capability of reporting events via the Ethernet (TCP/IP), when the ETHM-1 module is
connected.
•Event messaging to 16 phone numbers in the form of:
– 16 voice messages played back by an additional module (INT-VG, CA-64 SM or SM-2);
– 64 text messages defined by the installer (PAGER or SMS).
Event log
•21503 events.
•A separate memory space to store events required by the EN 50131 standard for Grade 2.
•Saving the content of received SMS messages to the event log.
•Event log printing capability.
Users
•8 master users (administrators).
•240 users.
•Capability to assign to the user:
– a code,
– a proximity card (125 kHz passive transponder, which may be in the form of a card, tag,
etc.),
– DALLAS iButton (chip)
– keyfob.
•Several user types.
•Authority level determining the scope of access to the system.
Additional features
•Access control functions realized by means of additional modules.
•64 system timers to automatically:
– arm/disarm the partitions;

4 Installer Manual SATEL
– control the outputs (switching the lights on/off, watering the garden, etc.).
•Partition timers (1 for each partition), to allow automatic arming/disarming.
Programming
•Local programming:
– keypad;
– computer with the DLOADX program installed, connected to the control panel RS-232
port.
•Remote programming:
– computer with the DLOADX program installed, communicating via modem, by means of
GPRS or via the Ethernet network (optionally, if the ETHM-1 module is connected to the
control panel);
– internet browser (optionally, if the ETHM-1 module is connected);
– mobile phone with suitable application installed (optionally, if the ETHM-1 module is
connected ).
Mainboard
•RS-232 port (RJ type socket) to allow:
– local programming by means of a computer with the DLOADX program installed;
– local system administration by means of a computer with the GUARDX program installed;
– remote programming using the DLOADX program via Ethernet (TCP/IP), if the ETHM-1
module is connected;
– support for external analog, GSM or ISDN modem;
– serial printer connection (for printing current events).
•Capability of the firmware updating without the need for disassembly of the control panel.
•Socket for connecting the INT-VG voice module, CA-64 SM voice synthesizers expander
or SM-2 synthesizer.
•Real time clock with calendar and battery backup.
•LEDs indicating the status of outputs, battery charging system and telephone dialer.
•Electrical protection of all hardwired zones and outputs, and communication buses.
•Switching power supply with short-circuit protection, provided with a battery status
supervision and low battery disconnect system.
3. Keypads
The INTEGRA 128-WRL control panel supports the following keypads:
INT-KSG – LCD keypad with touch keys;
INT-KLCD – LCD keypad with mechanical keys;
INT-KLCDR – LCD keypad with mechanical keys and built-in proximity card reader;
INT-KLCDK – LCD keypad with mechanical keys;
INT-KLCDL – LCD keypad with mechanical keys;
INT-KLCDS – LCD keypad with mechanical keys.
The recommended version of the keypad firmware (provides functionality consistent
with the requirements of EN 50131 for Grade 2):
−INT-KLCD / INT-KLCDR – 1.08 (or later);
−INT-KLCDK / INT-KLCDL / INT-KLCDS – 6.08 (or later);

SATEL INTEGRA 128-WRL 5
−INT-KSG – 1.02 (or later).
The keypads are available in a variety of color options for the enclosure, display and key
backlight. The color variant is indicated by the additional designation in the keypad name
(e.g. INT-KLCD-GR – green display and key backlight; INT-KLCD-BL – blue display and key
backlight).
Features of the INT-KSG keypad are described in a separate manual, delivered with the
keypad.
3.1 Features of keypads with mechanical keys
•Display 2 x 16 characters with backlight.
•LEDs indicating the status of the partitions and the system.
•Backlit keys.
•Built-in sounder.
•2 programmable hardwired zones:
– support for NO and NC detectors;
– support for Single EOL and Double EOL configuration.
•Tamper protection in 2 ways – cover removal and tearing enclosure from the wall.
•RS-232 port (PIN-5 socket) for administration of the security alarm system by means of a
computer with the GUARDX program installed.
4. Expansion modules
The expansion modules allow you to not only increase the number of available zones and
outputs (wired and wireless), but also enhance the system with additional functionality.
Not all of the following modules meet the requirements of EN 50131 for Grade 2.
4.1 Modules to be connected to the keypad bus
CA-64 PTSA. Mimic board. Enables visualization of the status of the alarm system partitions
and zones. The control panels support the mimic boards with electronics version 1.4 (or
later) and firmware version 4.0 (or later).
ETHM-1. Ethernet module. Enables reporting events as well as operating and programming
the control panel via the Ethernet network. The recommended module version: 1.06 (or
later).
INT-RS. Data converter.Makes it possible to connect the computer with the GUARDX
program installed in the same way as to the LCD keypad, report events through
a special external device, or operate the control panel using software other than that
offered by SATEL.
4.2 Modules to be connected to the expander bus
INT-RX / INT-RX-S. 433 MHz keyfobs receiver expansion module. Enables operation of
the alarm system using the 433 MHz keyfobs.
INT-CR. Proximity card arm/disarm device. Enables arming / disarming and alarm clearing
in many partitions by means of proximity cards, proximity tags and other passive
transponders.
INT-S / INT-SK. Partition keypad. Enables arming / disarming and alarm clearing in one
partition. Can perform access control functions.

6 Installer Manual SATEL
INT-SCR. Multifunctional keypad.It can work as:
INT-S. Partition keypad.
INT-SCR. Partition keypad with reader. Functionality similar to that of the partition
keypad.
INT-ENT. Entry keypad. The main task of the entry keypad is activation the delay for 3
INTERIOR DELAYED type zones. After expiry of the time period preset on the keypad,
unless the system is disarmed, the interior delayed zones will again act as instant
ones.
INT-SZ / INT-SZK. Code lock.Enables performance of the access control functions.
INT-R. Universal expander for card / chip readers. Supports the proximity card readers
manufactured by SATEL, readers with WIEGAND 26 interface or DALLAS chip readers.
Enables performance of the access control functions.
CA-64 E Zone expander. Adds 8 programmable hardwired zones to the security system.
CA-64 EPS. Zone expander with power supply. Adds 8 programmable hardwired zones to
the security system. Equipped with a built-in switching power supply.
CA-64 ADR. Addressable zone expander. Adds 48 addressable zones to the security
system. Equipped with a built-in switching power supply. Control panels support the
addressable zone expanders with firmware version 1.5 (or later).
CA-64 O. Output expander. Adds 8 programmable outputs to the security system. Made in
three versions:
CA-64 O-OC – 8 OC type outputs;
CA-64 O-R – 8 relay outputs;
CA-64 O-ROC – 4 relay outputs / 4 OC type outputs.
INT-ORS. DIN-rail output expander. Adds 8 programmable relay outputs to the security
system. The relays can control electrical devices supplied with 230 V voltage.
CA-64 OPS. Output expander with power supply. Adds 8 programmable outputs to the
security system. Equipped with a built-in switching power supply. Made in three
versions:
CA-64 OPS-OC – 8 OC type outputs;
CA-64 OPS-R – 8 relay outputs;
CA-64 OPS-ROC – 4 relay outputs / 4 OC type outputs.
INT-IORS. DIN-rail zone/output expander. Adds 8 programmable hardwired zones and 8
programmable relay outputs to the security system. The relays can control electrical
devices supplied with 230 V voltage.
CA-64 PP. Zone/output expander with power supply. Adds 8 programmable hardwired
zones and 8 programmable outputs (4 relay and 4 OC type) to the security system.
Equipped with a built-in switching power supply.
ACU-100 / ACU-250. ABAX wireless system controller. Enables the alarm system to be
operated using the ABAX keyfobs and the ABAX bidirectional wireless devices to be
used in the alarm system.
INT-VG. Voice module. Allows remote operation of the control panel from the telephone
keypad (interactive voice menu). It can store 16 voice messages for telephone
messaging.
INT-VMG. Voice message generator. Plays back prerecorded messages when specified
events occur in the system.
INT-KNX. KNX integration module. Enables interfacing of the control panel with the KNX
system.

SATEL INTEGRA 128-WRL 7
Fig. 1. INTEGRA 128-WRL security alarm system.

8 Installer Manual SATEL
4.3 Wireless devices supported by the controller
Detectors
•AFD-100 – wireless water flood detector.
•AGD-100 – wireless glass-break detector.
•AMD-100 – wireless magnetic contact.
•AMD-101 – dual channel wireless magnetic contact.
•AMD-102 – wireless magnetic contact with input for roller shutter detector.
•APD-100 – wireless passive infrared detector.
•APMD-150 – wireless dual motion detector.
•ARD-100 – wireless reorientation detector.
•ASD-110 – wireless smoke and heat detector.
•ATD-100 – wireless temperature detector.
•AVD-100 – wireless vibration detector and magnetic contact.
Sirens
•ASP-105 – wirelessly triggered outdoor siren.
•ASP-205 – wireless indoor siren.
Other
•ACX-200 – hardwired zone / output expander.
•ACX-201 – hardwired zone / output expander with power supply.
•ARF-100 – radio signal level tester.
•ASW-100 E / ASW-100 F – 230 V AC wireless controller.
5. System installation
Disconnect power before making any electrical connections.
The following tools will be useful during installation:
•blade screwdriver 2.5 mm,
•Phillips screwdriver,
•precision pliers,
•flat nose pliers,
•driller c/w a set of drill bits.
5.1 Installation plan
The installation must be preceded by preparation of a plan of the security alarm system. It is
advisable to draw up a sketch of the premises and mark on it all the devices that are to be
included in the alarm system: control panel, keypads, detectors, sirens, expansion modules
etc. When planning the installation location for the control panel and wireless devices of the
ABAX system, you must take into consideration the range of radio communication.
Remember that thick masonry walls, metal partitions, etc. will reduce the range of radio
signal. The control panel and other alarm system components should be installed within the
protected area.

SATEL INTEGRA 128-WRL 9
5.2 Estimation of the system current consumption
At the security system planning stage you should sum up the currents consumed by all
devices included in the system (control panel mainboard, keypads, additional modules,
detectors, sirens, etc.). The calculation should take into account the battery charging current.
If the sum of currents exceeds the maximum output current of the control panel power
supply, expander with power supply or an additional power supply unit should be used.
The sum of currents consumed by the devices connected to the power supply unit (expander
with power supply) must not exceed the power supply output current.
If you plan to connect devices to particular power outputs (of the control panel, expander with
power supply, etc.), remember that the sum of currents consumed by these devices must not
exceed the maximum current carrying capacity of those outputs.
5.3 Cabling
It is recommended that unscreened straight-through cable be used for making electric
connections between devices included in the system (using the twisted-pair type of cable,
e.g. UTP, STP, FTP, is not advisable).
If you use the twisted-pair type of cable, remember that the DTM and CKM / DT and
CK (data and clock) signals must not be sent through one twisted-pair cable.
Select cross-section of the power supply wires so that the supply voltage drop between the
power supply and the supplied device should not exceed 1 V as against the output voltage.
In order to guarantee correct functioning of the system components it is important that
resistance and capacitance of the signal wires be as low as possible. When the distances
between the devices are greater, several wires connected in parallel may have to be used for
each signal, in order to reduce conductor resistance. This, however, may lead in
consequence to an increase in conductor capacitance. Too high resistance or capacitance of
the cables connecting the control panel to keypads or expansion modules can prevent the
devices from working correctly (e.g. the control panel will be unable to identify devices,
absence of devices will be reported, etc.). When selecting the length of cables, follow
recommendations set out in sections on connection of particular types of devices.
When making the cabling, remember that there must be sufficient distance between the low-
voltage wires and the 230 V AC power supply wires. Avoid running the signal cables in
parallel to and in close proximity of the 230 V AC supply cables.
The cables should not run in immediate vicinity of antennas, because it could adversely affect
radio communication.
5.4 Installation of control panel mainboard
The control panel mainboard contains electronic components sensitive to
electric charges.
You must complete all wiring, connections and device installations before
connecting the battery or applying AC mains to the control panel.
The control panel should be installed indoors, in spaces with normal humidity of air. The
control panel must be protected against unauthorized access.
It is recommended that the control panel be mounted high above the floor. This will allow you
to get a better range of radio communication and avoid the risk of the control panel being
accidentally covered by people moving around the premises.
A 230 V AC power supply circuit with protective grounding must be available at the control
panel installation place.

10 Installer Manual SATEL
Fig. 2. Control panel mainboard (version 2.1).

SATEL INTEGRA 128-WRL 11
5.4.1 Description of the mainboard
Explanations for Fig. 2:
battery connection cables (red +, black -).
LEDs indicating the status of high-current outputs.
pins for setting battery charging current:
−pins shorted (jumper on) – 400 mA
−pins open (no jumper) – 800 mA
CHARGE LED indicating the battery charging.
RS-232 port (RJ type socket).
STTS LED indicating the operation status of the supervision circuit of ABAX wireless
system.
RESET pins for emergency starting the control panel (see: EMERGENCY PROCEDURE OF
THE CONTROL PANEL START-UP p. 20).
lithium battery for clock and RAM backup. Its removal will result in loss of the clock
settings and all data stored in RAM.
Insert the battery in its socket before starting the control panel.
socket to connect antenna for communication with ABAX wireless devices.
SIM card socket. It is not recommended to insert the SIM card into its socket before the
card PIN code has been programmed in the control panel.
GSM STATUS LED indicating the telephone and GSM network status:
−OFF – the telephone disabled,
−ON – outgoing voice call,
−lit, getting dimmed every 0.5 second – incoming voice call,
−flashing slowly – CSD communication,
−flashing rapidly – GPRS communication
−1, 2, 3 or 4 flashes every 2 seconds – telephone standby mode (the number of
flashes indicates the signal strength).
LEDs indicating the status of low-current outputs.
socket for connecting the INT-VG voice module, CA-64 SM voice synthesizer expander
or SM-2 synthesizer.
socket for GSM/GPRS communication antenna.
Description of terminals:
AC - power supply inputs (18 V AC)
COM - common ground
OUT1...OUT2 - programmable high-current outputs (if output is not used, the 2.2 kΩ
resistor should be connected between the output and common terminals)
+KPD - power supply output for powering the devices connected to keypad bus
(13.6...13.8 V DC)

12 Installer Manual SATEL
DTM - keypad bus data
CKM - keypad bus clock
+EX - power supply output for powering the devices connected to expander bus
(13.6...13.8 V DC)
DT - expander bus data
CK - expander bus clock
AUX - power supply output (13,6...13,8 V DC)
Z1...Z8 - zones
OUT3...OUT8 - programmable low-current outputs, OC type
5.5 Connecting devices to the keypad bus
The bus wires must be run in one cable.
The distance between the keypad (or other device to be connected to keypad bus) and
the control panel may be up to 300 m.
Devices installed far from the control panel may be supplied locally from a separate
power source.
Supply voltage measured at the LCD keypad terminals, with the display and key
backlight on, must not be lower than 11 V.
Fig. 3. Connection of keypads (other devices should be connected in a similar way).
The Table 1 shows the number of wires required for correct connection of the device to the
keypad bus if the straight-through cable with conductor cross-section 0.5 mm2is used.

SATEL INTEGRA 128-WRL 13
+KPD
COM
CKM
DTM
Distance
Number of wires
up to 100 m 1 1 1 1
100-200 m 2 2 1 1
200-300 m 4 4 2 2
Table 1.
5.5.1 Addressing devices connected to the keypad bus
Each device to be connected to the keypad bus must have its own individual address from
the 0 to 7 range. Addresses must not repeat (the control panel does not support devices
having identical addresses). It is recommended that consecutive addresses be assigned
starting from 0.
In keypads, the address is set by software means. By default, address 0 is set. When started
with factory default settings, the control panel will support all keypads connected to the bus,
irrespective of what addresses are set in them. Thus it is possible to set correct individual
addresses in the keypads and perform identification of all devices connected to the bus.
In other devices to be connected to the keypad bus, the address is to be set using the
DIP-switches or the pins.
Programming keypad address by means of the service function
1. Enter the service code (by default 12345) and press the key.
2. Using the or keys, find the SERVICE MODE item in the function list and press the
or key.
3. Start the KEYPADS ADDR. function (STRUCTURE HARDWARE IDENTIFICATION
KEYPADS ADDR.).
4. The message shown in Fig. 4 will appear on display of all keypads connected to the
control panel.
Fig. 4. Programming the keypad address with the service function..
5. Enter a proper address from the 0-7 range in the selected keypad(s). The address
change will be confirmed by four short beeps followed by one long beep.
6. To terminate the address change function, press the key. The function will be
terminated automatically after 2 minutes from being started. Termination of the
function is equivalent to restarting the keypad (return to the main service mode
menu will follow in the keypad from which the function has been started).
Programming keypad address without entering the service mode
This method of address programming is particularly useful when – due to repeating
addresses – the keypad support has been disabled and entering the service mode is
impossible.
1. Disconnect the keypad power supply (KPD) and the CKM and DTM signal wires.
2. Short-circuit the keypad CKM and DTM terminals.
3. Switch on keypad power supply.
n=0...7, currently set keypad
address

14 Installer Manual SATEL
4. A message indicating the current address will appear on the display.
5. Enter a new address. The keypad will confirm execution of the function by four short
beeps followed by one long beep. If it is necessary to change the entered address,
press the key (keypad restart will follow and a corresponding message will appear
on the display).
6. Disconnect the keypad power supply.
7. Open the keypad CKM and DTM terminals.
8. Connect the keypad correctly to the control panel.
5.5.2 Numeration of keypad zones
The address set in the keypad defines which numbers in the system will be assigned to the
keypad zones (see Table 2). You can define for each keypad whether or not its zones will be
used in the system. If the zone numbers of keypad and expander coincide, the keypad zones
have priority (in such a case, the corresponding expander zones will not be supported).
Keypad
address
Zone number in the system
Z1
Z2
0 113 114
1 115 116
2 117 118
3 119 120
4
121
122
5 123 124
6 125 126
7
127
128
Table 2.
5.5.3 Connecting computer to the keypad RS-232 port
In some keypads, the RS-232 port makes it possible to connect a computer with the GUARDX
program installed (see Fig. 5). It is recommended that the straight-through unscreened cable
be used for making the connection (using the twisted-pair type of cable, e.g. UTP, STP, FTP,
is not advisable). The distance between computer and keypad can be up to 10 m.
Fig. 5. Computer connection to the keypad RS-232 port. Shown on the right is the keypad
interface. Shown on the left is the DB-9 female connector from soldering points side.
Activate the COMMUNICATION RS option in keypads to which the computer with GUARDX
program is connected. Data exchange with the computer will begin automatically as
soon as the GUARDX program is started.

SATEL INTEGRA 128-WRL 15
5.6 Connecting devices to the expander bus
The bus wires must be run in one cable.
The total length of the expander bus may not exceed 1000 m.
The module may be powered directly from the control panel if the distance between
control panel and module does not exceed 300 m. Where the distance is greater,
another source of power must be provided for the module (a power supply unit or an
expander with power supply).
Fig. 6. Connection of modules without power supply.
Fig. 7. Connection of modules with power supply.

16 Installer Manual SATEL
The Table 3 shows the number of wires required for correct connection of the device to the
expander bus if the straight-through cable with conductor cross-section 0.5 mm2is used.
CK
DT
COM
Distance
Number of wires
up to 300 m 1 1 1
300 – 600 m 2 2 2
600 – 1000 m 2 2 4
Table 3.
5.6.1 Connecting the INT-VG module or CA-64 SM expander
When connecting the INT-VG voice module or the CA-64 SM voice synthesizer expander, the
CLK and DTA wires only are to be connected to the bus. Each of these devices is additionally
provided with the PIN5 connector, which is to be connected to the dedicated socket on the
control panel electronics board.
5.6.2 Addressing devices connected to the expander bus
Each device to be connected to the expander bus must have its own individual address from
the 0 to 31 range. The addresses of devices must not repeat (the control panel does not
support devices having identical addresses). It is recommended that consecutive addresses
be assigned starting from 0. In most devices, the address is set by means of DIP-switches.
The address affects numeration of zones and outputs in the system (see section
NUMERATION OF ZONES AND OUTPUTS IN THE SYSTEM p. 29).
5.7 Connecting the detectors
How the detector is connected to the zone must be suitable for the configuration chosen for
that zone. The zones on the control panel mainboard support the following configurations:
NC – the wiring type dedicated to connecting devices with the NC (normally closed) alarm
output. Opening the circuit will trigger an alarm.
NO – the wiring type dedicated to connecting devices with the NO (normally open) alarm
output. Closing the circuit will trigger an alarm.
EOL – this wiring type may be used to connect devices having the NC or NO alarm output.
Closing or opening the circuit will trigger an alarm.
2EOL/NC – the wiring type recommended to connect detectors having the NC alarm output
and a tamper output. The zone can recognize 3 states: normal, alarm and tamper.
2EOL/NO – the wiring type similar as 2EOL/NC, but for detectors with the NO alarm output.
Roller – the wiring type dedicated to connecting roller shutter detectors.
Vibration – the wiring type dedicated to connecting vibration detectors. The zone will also
accept connection of a detector with the NC alarm output (e.g. a vibration detector and
a magnetic contact can be connected in parallel).
Follow output – in case of this configuration the detector should not be connected. The zone
status depends only on that of the selected output (the output is not to be physically
connected to the zone).

SATEL INTEGRA 128-WRL 17
Fig. 8. The ways to connect detectors to zones. The detector outputs are designated with
letters: A - alarm, T – tamper. R=R1+R2.
5.7.1 End-of-line resistors
The value of R1 and R2 resistors is programmable within the range from 500 Ωto 15 kΩ(the
sum of preset values may not exceed 15 kΩ– see PROGRAMMING manual). The factory preset
values are as follows:
R1 = 1.1 kΩ;
R2 = 1.1 kΩ.
If the resistor value in the keypad or expander is not programmable, in Single EOL
configuration, the 2.2 k Ω resistor is required, and in Double EOL (2EOL) configuration
– two 1.1 k Ω resistors.
5.8 Connecting the sirens
If high-current output is not used, the 2.2 k Ω resistor should be connected between the
output and common terminals.

18 Installer Manual SATEL
Fig. 9. The way of connecting sirens. I – siren without own power supply – alarm signaling
triggered by high-current outputs. II - siren with own power supply – alarm signaling triggered
by low-current outputs, the high-current serving as power supply output. The value of
resistors R is 2.2 kΩ. In both cases, tamper circuit is connected to zone Z8.
5.9 Connecting power supply
Complete all wiring to the control panel before connecting AC power or the
battery.
Before connecting power supply, insert the clock and RAM backup battery into
its socket on the mainboard.
5.9.1 Main power supply
The control panel requires 18 V AC (±10%) power supply. Using a transformer of at least
40 VA power is recommended.
Never connect two devices with power supply unit to one transformer.
Before connecting transformer to a circuit from which it will be powered, make
sure the circuit is de-energized.
The transformer should be permanently connected to the 230 V AC mains supply. Before you
make the cabling, familiarize yourself with the electrical installation of the facility. Make sure
that the circuit you choose for powering the control panel will be always alive. The power
supply circuit should be protected with a proper safety device. The owner or user of the alarm
system should be instructed on how to disconnect the transformer from the mains (e.g. by
indicating the fuse which protects the control panel supply circuit).
5.9.2 Backup power supply
A 12 V lead-acid sealed battery should be connected to the control panel as a backup power
source. The battery capacity must be adequately selected to match current consumption in