Satel PERFECTA Owner's manual

Alarm control panel
PERFECTA 64 M
Firmware version 2.00
QUICK USER MANUAL
perfecta_64_M_us_en 01/23
SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. [phone]
www.satel.pl
EN

Changes, modifications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
Hereby, SATEL sp. z o.o. declares that the radio equipment type PERFECTA 64 M is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity
is available at the following internet address: www.satel.pl/ce
SATEL aims to continually improve the quality of its products, which may result in changes in
their technical specifications and software. Current information about the changes being
introduced is available on our website.
Please visit us at:
https://support.satel.pl
ATTENTION!
The alarm system cannot prevent burglary or robbery. Its purpose is to signal
emergency situations. It should be installed by qualified professionals who will inform
you about the principles of its operation and provide regular maintenance and testing.
We recommend that the alarm system be regularly tested to make sure that it will react
properly in case of burglary or robbery.
Factory default codes:
Service code: 12345
User 62 code: 1111
The following symbols may be used in this manual:
- note,
- caution.

Thank you for choosing this product by SATEL. Before you start using the
alarm system, familiarize yourself with the instructions outlined in the
following quick user manual. For more information, please refer to the full
user manual available at www.satel.pl. Scan the QR code to go to our
website and download this or other manuals.
It is recommended that the installer prepare and deliver to the users a customized
alarm system user manual. This manual must include all changes and modifications
made in relation to the factory default settings.
The installer should train the users in the rules of operating the alarm system.
Using the keypads
The alarm system should include at least one keypad.
The following manual includes instructions on how to use the wired PRF-LCD keypad and the
wireless PRD-LCD-WRL / PRF-LCD-A2 keypad. For instruction on how to use the
INT-KSG2R, INT-TSG2 and INT-TSH2 keypads, please refer to the manuals included with
these manuals.
The wired keypad is faster to react to user actions than the wireless keypad. The wireless
keypad powered by an external power supply (connected to the APS-055 power supply)
works similarly to the wired keypad. In the wireless keypad powered by the battery, the sleep
mode is started after 20 seconds of inactivity. When the keypad is in the sleep mode,
the display is off and the LED indicators, sound signaling, backlight (of display and keys) and
proximity card reader are disabled. To wake up the keypad, press e.g. .

2 PERFECTA 64 M SATEL
LED indicators
green
two LEDs (marked I and II) –ask the installer which LED indicates the
state of which partition
ON –at least 1 partition is armed
flashing –exit delay countdown in at least 1 partition
red
two LEDs (marked I and II) –ask the installer which LED indicates the
state of which partition
ON or flashing –alarm or alarm memory in at least 1 partition
yellow
flashing –trouble or trouble memory
blue
ON –service mode is active and service menu is displayed
flashing –service mode is active but service menu is hidden or
displayed in another keypad
Display
Normal mode
Date and time or the keypad name are displayed in the upper
line.
Press to switch to the system preview mode.
System preview mode
Information on system state are displayed. The installer selects
the items to be displayed. They can be date and time, partition /
zone / output state symbols, power consumption, etc.
Press to switch to the normal mode.
Messages
The keypad displays messages on:
alarm
entry delay countdown
exit delay countdown
alarm memory
Keys
...
press to enter digits (code, partition number, etc.)
press and hold for 3 seconds to view the troubles
press and hold for 3 seconds to turn on/off the keypad CHIME
press and hold for 3 seconds to switch the keypad between the normal mode
and the system preview mode
press and hold for 3 seconds to trigger the medical alarm
enter the code and press to arm in full mode [if the system is disarmed
and there is no alarm] or disarm the system and clear the alarm [if the system
is armed and/or there is an alarm]
press and hold for 3 seconds to trigger the panic alarm

SATEL PERFECTA 64 M 3
enter the code and press to enter the user menu
press and hold for 3 seconds to trigger the fire alarm
used for full arming (see: “Arming”)
used for night arming (see: “Arming”)
used for day arming (see: “Arming”)
used to disarm the system and clear the alarm (see: “Disarming and alarm
clearing”)
Daily operation
Arming
Arming with code
Partition 1
[code] –full arming
[code] –day arming
[code] –night arming
Partition 2
[code] –full arming
[code] –day arming
[code] –night arming
Partition 3
[code] –full arming
[code] –day arming
[code] –night arming
Partition 4
[code] –full arming
[code] –day arming
[code] –night arming
All partitions to which
you have access
[code] / [code] –full arming
[code] –day arming
[code] –night arming
Arming with proximity card
[only PRF-LCD-A2]
All partitions to which
you have access
bring the card close to the keys and move it away / bring the
card close to the keys and hold for about 3 seconds (ask the
installer which method to use)
Quick arming (without code / card)
Partition 1
–full arming
–day arming
–night arming

4 PERFECTA 64 M SATEL
Partition 2
–full arming
–day arming
–night arming
Partition 3
–full arming
–day arming
–night arming
Partition 4
–full arming
–day arming
–night arming
All partitions
–full arming
–day arming
–night arming
Arming without delay
when arming, hold for 3 seconds the key used to select the arming type: , or
(when arming with code, do it after you enter the code)
Terminating the exit delay countdown
when the exit delay countdown is running, press , or for 3 seconds (no
matter which key you press).
Not ready for arming
if you tried to arm the system but the message “Not ready” was displayed, it means the
control panel detected a problem: violated zone (e.g. open window), bypassed zone, tamper
or trouble
Disarming and alarm clearing
Disarming / alarm clearing with code
Partition 1
[code]
Partition 2
[code]
Partition 3
[code]
Partition 4
[code]
All partitions to which
you have access
[code] / [code]
Disarming / alarm clearing with proximity card
[only PRF-LCD-A2]
All partitions to which
you have access
bring the card close to the keys and move it away

SATEL PERFECTA 64 M 5
Alarm clearing without disarming
[code] / [code] / [code]
Output control without code
Ask the installer if the control methods described below are available to you and which
outputs can be controlled this way.
Quick output control
Activate output
[digit key]
Deactivate output
[digit key]
Output control with proximity card
[only PRF-LCD-A2]
Switch outputs
bring the card close to the keys and hold for about 3 seconds
User menu
The list of available functions depends on your rights, as well as on the state and
configuration of the system.
User functions
Change own code
[code]
Add new user
[code]
Edit user
[code]
Delete user
[code]
Reset outputs
[code]
Inhibit zones
[code]
Isolate zones
[code]
View event log
[code]
Set time and date
[code]
Program timer settings
[code]
Program thermostat settings
[code]
View troubles / system state
[code]
Control outputs
[code]
Test zones
[code]

6 PERFECTA 64 M SATEL
Test outputs
[code]
Check the level of cellular / radio signal
[code]
Start test transmission
[code]
Change control panel ID (communication
via the SATEL server)
[code]
Check the IMEI number / ID number
[code]
Check the firmware version of devices in
the system
[code]
Check temperature (ABAX 2 devices with
temperature sensor)
[code]
Check power consumption (ASW-200
smart plug)
[code]
Check the SIM 1 card credit
[code]
Check the SIM 2 card credit
[code]
Top up the SIM 1 card
[code]
Top up the SIM 2 card
[code]
Enter PUK code for the SIM 1 card
[code]
Enter PUK code for the SIM 2 card
[code]
Functions of keys in the user menu
...
enter digits, letters and other characters
enable / disable an option
check / uncheck an item
start a function
save changes and quit the function
exit the user menu
quit the function (usually without saving changes)
scroll up the list
move the cursor left
clear the character to the left of the cursor (edit numbers and names)
exit the graphic mode
exit the submenu
move the cursor left
enter the graphic mode

SATEL PERFECTA 64 M 7
enter the submenu
start a function
move the cursor right
enter the graphic mode
scroll down the list
change the letter case (edit names)
exit the graphic mode
Keyfobs
You can use a keyfob if the keyfob module is connected to the control panel. The keyfob can
start up to 6 functions. For information about functions assigned to individual buttons / button
combinations, please consult the person who has configured the keyfob settings. If you have
the APT-200 keyfob, ask the person about the keyfob LEDs. They can indicate the system
state.
Listening in
You can use the listening in function to check what is happening in the protected premises,
e.g. to verify the alarm. You can use the listening in function:
by calling the control panel phone number,

8 PERFECTA 64 M SATEL
after having listened to the voice message that notified you of a new event in the control
panel.
Ask the installer if the listening in function is available and if both uses are supported.
SMS control
You can control your alarm system by sending SMS messages containing appropriate control
commands. The SMS message must be sent to the control panel phone number (number of
the currently used SIM card). Agree with the installer on:
content of the control commands.
functions that are to be started by these commands.
phone numbers from which it will be possible to send the control commands.
More than one control command can be inserted in one SMS message.
When sending the USSD codes, the SMS message must have the following form:
xxxx=yyyy=
where “xxxx” is the control command and “yyyy” is the USSD code supported by the cellular
network operator.
Using the command that controls sending of the USSD codes, you can send an SMS
message via the control panel. The SMS message you will send to the control panel must
have the following form:
xxxx=tttt:cccc=
where “xxxx” is the control command, “tttt” is the phone number to which the control panel is
to send the SMS message, and “cccc” is the content of SMS message to be sent by the
control panel.
The control panel is case sensitive.
PERFECTA CONTROL application
The PERFECTA CONTROL is an application which enables remote operation of the alarm
system from mobile devices. The application can also send push notifications with
information on alarm system events. If the IP cameras are installed in the protected
premises, you can watch video from these cameras in the application.
You can download the application from the internet stores: “Google play” (Android system
devices) or “App Store” (iOS system devices).
The tutorial will assist you in the configuration process and show you what to do next.
To add a new alarm system that you want to control from the application, you will need:
control panel IMEI number and ID number. You can:
–obtain them in the form of a QR code from the installer or a user who has already
entered the control panel data to application,
–access them in the keypad ([code] ).
your user code.
Failure to arm
The installer can configure the alarm system in such a manner that it will not become armed
after the exit delay countdown ends. It applies to situations when the control panel detected