Satel PERFECTA User manual

Alarm control panel
PERFECTA 64 M
Firmware version 2.00
USER MANUAL
perfecta_64_M_u_en 02/23
SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. [phone]
www.satel.pl
EN

IMPORTANT
Changes, modifications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
To ensure adequate protection, the alarm security system must be in good working order,
therefore SATEL recommends that it be regularly tested.
The alarm system cannot prevent burglary, hold-up or fire from happening, but in emergency
situation it will allow you to take steps to minimize the potential damage (by triggering optical
or acoustic alarm signal, notifying appropriate authorities of the alarm etc.). Thus, it can deter
any would-be intruders.
SATEL aims to continually improve the quality of its products, which may result in changes in
their technical specifications and software. Current information about the changes being
introduced is available on our website.
Please visit us at:
https://support.satel.pl
Hereby, SATEL sp. z o.o. declares that the radio equipment type PERFECTA 64 M is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity
is available at the following internet address: www.satel.pl/ce
Factory default codes:
Service code: 12345
User 62 code: 1111
The following symbols may be used in this manual:
- note,
- caution.

CONTENTS
1. Introduction........................................................................................................................4
2. Technical reliability of the alarm system............................................................................4
3. Alarm system operating costs ...........................................................................................4
4. Glossary............................................................................................................................4
5. EN 50131 standard for Grade 2 consequences ................................................................6
6. Keypads ............................................................................................................................6
6.1 Keypads description..................................................................................................7
6.1.1 LED indicators............................................................................................................7
6.1.2 Display .......................................................................................................................8
Normal mode ............................................................................................................................9
System preview mode...............................................................................................................9
Messages................................................................................................................................10
6.1.3 Keys.........................................................................................................................10
6.1.4 Sound signaling........................................................................................................10
Beeps generated when operating...........................................................................................11
Beeps generated during programming...................................................................................11
Event signaling........................................................................................................................11
6.2 Codes......................................................................................................................12
6.2.1 Factory default codes...............................................................................................12
6.3 Proximity cards .......................................................................................................12
6.4 Arming.....................................................................................................................12
6.4.1 Arming with code......................................................................................................12
Arming without partition selection...........................................................................................12
Arming the selected partition..................................................................................................13
6.4.2 Arming with proximity card.......................................................................................13
6.4.3 Quick arming............................................................................................................13
6.4.4 Arming without delay................................................................................................13
6.4.5 Terminating the exit delay countdown......................................................................13
6.4.6 Service mode and arming........................................................................................13
6.4.7 System problems and arming failure........................................................................13
System not ready and forced arming......................................................................................14
Failure of arming procedure....................................................................................................14
6.5 Disarming and alarm clearing .................................................................................14
6.5.1 Disarming and clearing alarm with code..................................................................15
Disarming and alarm clearing without partition selection.......................................................15
Disarming and alarm clearing in selected partition.................................................................15
6.5.2 Disarming and clearing alarm with proximity card....................................................15
6.5.3 Alarm clearing without disarming.............................................................................15
6.6 Triggering the alarm from keypad ...........................................................................15
6.7 Turning the CHIME on /off ......................................................................................15
6.8 User menu ..............................................................................................................15
6.8.1 Navigating through the menu and running functions................................................16
Using the arrow keys..............................................................................................................16
Using the number shortcuts....................................................................................................16
6.8.2 Data editing..............................................................................................................17
Selection from the single-choice list .......................................................................................17
Selection from the multiple-choice list ....................................................................................17
Entering decimal values..........................................................................................................17
Entering hexadecimal values..................................................................................................17
Entering names.......................................................................................................................18
6.8.3 User functions list.....................................................................................................18
6.9 Changing code........................................................................................................25
6.10 Users.......................................................................................................................25

2 PERFECTA 64 M SATEL
6.10.1 Adding a user...........................................................................................................26
6.10.2 Editing a user...........................................................................................................27
6.10.3 Removing a user...................................................................................................... 27
6.10.4 Adding keyfob..........................................................................................................27
6.10.5 Configuring keyfob settings .....................................................................................27
6.10.6 Removing keyfob.....................................................................................................28
6.10.7 Adding proximity card.............................................................................................. 28
Entering card number manually............................................................................................. 28
Reading card number using the reader................................................................................. 28
6.10.8 Removing proximity card ......................................................................................... 28
6.11 Outputs reset...........................................................................................................29
6.12 Zone bypassing.......................................................................................................29
6.12.1 Zone inhibiting ......................................................................................................... 29
6.12.2 Zone isolating ..........................................................................................................30
6.13 Viewing the event log..............................................................................................30
6.14 Settings...................................................................................................................30
6.14.1 Setting the clock ......................................................................................................30
6.14.2 Programming the timer settings............................................................................... 30
Setting the timer start / stop time........................................................................................... 30
Setting an exception .............................................................................................................. 31
Timer activation / deactivation ............................................................................................... 31
Rules for programming the timer settings.............................................................................. 32
6.14.3 Programming the thermostat settings...................................................................... 32
Programming temperature T1 (economy temperature)......................................................... 32
Programming temperature T2 (comfort temperature)............................................................ 33
Programming hysteresis........................................................................................................ 33
Thermostat activation / deactivation...................................................................................... 33
Rules for programming the thermostat settings..................................................................... 33
6.15 Checking the troubles / system state.......................................................................34
6.15.1 Information on system state..................................................................................... 34
6.15.2 What to do in the event of trouble............................................................................ 34
6.15.3 Trouble memory and clearing the trouble memory.................................................. 34
6.16 Output control..........................................................................................................34
6.16.1 Quick control of outputs...........................................................................................34
Quick activation of output....................................................................................................... 34
Quick deactivation of output................................................................................................... 34
6.16.2 Controlling the outputs by means of function........................................................... 34
6.16.3 Controlling the outputs by means of proximity card................................................. 35
6.17 Tests .......................................................................................................................35
6.17.1 Zone test..................................................................................................................35
6.17.2 Output test............................................................................................................... 35
6.17.3 Checking the level of cellular / radio signal.............................................................. 36
6.17.4 Starting the test transmission ..................................................................................36
6.17.5 ID change ................................................................................................................36
6.17.6 Checking the IMEI number / ID number .................................................................. 36
6.17.7 Checking the firmware version of devices in system............................................... 37
6.18 SIM cards................................................................................................................37
6.18.1 Checking the balance of SIM card........................................................................... 37
6.18.2 Topping up the SIM card .........................................................................................37
6.18.3 Unblocking the SIM card.......................................................................................... 37
6.19 Replacing battery in wireless keypad......................................................................37
6.20 Service access........................................................................................................38
6.21 Establishing communication with PERFECTA SOFT via GPRS/LTE.......................38
6.22 Service mode ..........................................................................................................39

SATEL PERFECTA 64 M 3
7. Listening in......................................................................................................................39
8. Keyfobs ...........................................................................................................................39
9. SMS control.....................................................................................................................40
10. PERFECTA CONTROL application.................................................................................41
10.1 First start of PERFECTA CONTROL (Android).......................................................41
10.1.1 Adding a new alarm system by using the QR code (Android)..................................41
10.1.2 Adding a new alarm system without using the QR code (Android)..........................42
10.2 First start of PERFECTA CONTROL (iOS).............................................................43
10.2.1 Adding a new alarm system by using the QR code (iOS)........................................43
10.2.2 Adding a new alarm system without using the QR code (iOS) ................................44
11. Sirens..............................................................................................................................44

4 PERFECTA 64 M SATEL
1. Introduction
Thank you for choosing this product by SATEL. Read this manual before you start using the
alarm system.
It is recommended that the installer prepare and deliver to the users a customized
alarm system user manual. The manual must include all changes and modifications in
relation to the factory default settings.
The installer should train the users in the rules of operating the alarm system.
2. Technical reliability of the alarm system
A failure of any component of the alarm system will result in deterioration of the level of
protection. Unfortunately, the devices which are installed outside (e.g. the outdoor sirens) are
exposed to the adverse effects of weather. During storms, the devices connected to the
electrical system are vulnerable to damage as a result of atmospheric discharge.
The control panel is provided with a number of safeguards and automatic diagnostic features
to test the system performance. Detection of irregularities is signaled in the keypad by an
indicator. Youshould immediately respond to such a signal, and, if necessary, consult
the installer.
In addition, some features designed for testing the alarm system are available in the control
panel. They make it possible to check the detectors, sirens, control panel cellular
communicator, etc for correct functioning. Only regular testing and inspection of the
alarm system will allow you to keep a high level of protection against intrusion.
It is recommended that the installer, at the request of the user, carry out periodic
maintenance of the alarm system.
It is in the interest of the user to anticipate and plan in advance the procedures in case an
alarm is set off by the control panel. It is important to be able to verify the alarm, determine its
source and take appropriate actions (e.g. evacuation in the event of a fire alarm).
3. Alarm system operating costs
The control panel can inform the users and the monitoring station about the status of
protected facility. Realization of these features means financial costs. The amount of the
costs incurred depends on the amount of information sent. A failure, as well as an incorrect
programming of the control panel, may result in increased costs (due to making of excessive
number of calls).
Please inform the installer, which is a priority: to deliver information at any cost, or to prevent
excessive costs. For example, after an event code has failed to be sent successfully to the
monitoring station, the control panel may repeat attempts every few minutes to send the code
or to cease the attempts to send the code until a next event occurs.
4. Glossary
Alarm – warning that an intruder or other hazard (e.g. glass pane break, gas detection, etc.)
has been detected in the protected area by the detectors. The alarm can be signaled in
keypads or by sirens (during a defined time or until cleared). Additionally, information on
the alarm can be sent to the monitoring station or the user.

SATEL PERFECTA 64 M 5
Alarm zone – the zone whose violation can result in the alarm being triggered. The alarm
zones can be either instant (violation will trigger the alarm at once) or delayed (violation
will only trigger the alarm after a defined period of time has elapsed, e.g. the entry delay).
Armed mode – the status of alarm system in which zone violation will trigger the alarm.
Code – a sequence of digits used for user authentication. It allows the user to operate the
alarm system by using keypad.
Day armed mode – the status in which only some zones in the partition are armed, as
selected by the installer. The indicated zones will be armed during the day, when the
user(s) stay in the protected area, but there is no risk of the zones being violated by the
user(s). If no such zones are indicated by the installer, this arming mode is unavailable.
Detector – the basic component of alarm system, which analyzes the environment and, if
a situation recognized as a threat occurs, transmits appropriate information to the control
panel (e.g. motion detectors on detecting motion, magnetic contacts on opening the
door/window, glass-break detectors on breaking glass pane, gas detectors on sensing
gas, etc.).
Entry delay – time counted from entering into the protected area, which makes it possible to
disarm the partition before the alarm is triggered.
Entry route – the route which the user must have to follow after entry into the protected area
before being able to disarm the system. It is usually the same as the exit route.
Exit delay – time counted from starting the arming procedure in the partition, which makes it
possible to leave the protected area before the alarm is triggered.
Exit route – the route which the user must have to take after arming before he leaves the
protected area. It is usually the same as the entry route.
Fire alarm – alarm triggered by fire detectors, or from the keypad, in the event of fire.
Full armed mode – the status in which all zones belonging to the partition are armed.
Installer – the person who has installed and configured the alarm system.
Medical (auxiliary) alarm – alarm triggered by means of a button, or from the keypad, if it is
necessary to call the medical assistance.
Night armed mode – the status in which only some zones in the partition are armed, as
selected by the installer. The indicated zones will be armed at night, when the user(s) stay
in the protected area, but there is no risk of the zones being violated by the user(s). If no
such zones are indicated by the installer, this arming mode is unavailable.
Panic alarm – alarm triggered by means of the panic button, or from the keypad, in case of
a hold-up.
Partition – a part of the protected area, composed of a number of zones. The division into
partitions makes it possible to limit the access to part of the premises to some selected
users, and to arm/disarm the system only in part of the protected area.
Protected area – the area supervised by detectors being part of the alarm system.
Proximity card – a passive transponder that can be used for user authentication if a device
that has a proximity card reader is installed in the alarm system. The transponder can be
a card, a tag, etc.
Reporting – reporting events that occurred in the alarm system to the monitoring station. The
information about occurrence of an event can be transmitted via cellular network. The
companies offering the alarm system monitoring service undertake to intervene if specific
events occur (e.g. alarms, troubles, etc.).
Service code – a code that allows access to the service mode, as well as some functions in
the user menu.

6 PERFECTA 64 M SATEL
Service technician – the person whose function is to control operability of the installed alarm
system and its components, as well as to eliminate possible problems. These duties can
be fulfilled by the installer or a person assigned by him.
Siren/beacon – a device providing information about alarms or other events in the alarm
system by means of acoustic or optical signaling.
Tamper alarm – reaction of the alarm system to opening the housing of a device which is
part of the alarm system, tearing off the device from the wall, cutting through the alarm
system cables, etc. Actions taken by the alarm system may be similar as in the event of
alarm, however, if the tamper alarm occurs, it is advisable to call in the installer so that he
can make a checkup.
User – a person which can operate the alarm system, using a code or remote control keyfob.
Warning alarm – in some situations, when the alarm criteria are met, the alarm system does
not take up immediately all the actions provided for in the event of alarm. These actions
are postponed, reaction of the system being limited to signaling warning alarm in keypads
or on indoor sirens/beacons. Thus, the user who has made a mistake entering the
protected area (without disarming the system first), has some extra time to disarm the
system. Contact your installer to obtain detailed information on the situations when the
alarm will be preceded by warning alarm.
Zone – 1. a separated portion of the protected area that can supervised by a detector.
A single zone can be a corridor, window or door. 2. the terminals on control
panel/expander electronics board to which you can connect a detector or another device
whose state is to be supervised (panic button, siren tamper contact, power supply output
indicating loss of 230 VAC supply, etc.).
Zone bypassing (inhibiting / isolating) – procedure preventing the alarm from being
triggered by the selected zone when it is in the armed mode. Violations of the zone will be
ignored by the control panel.
Zone violation – a change of the zone status to another, different from that defined for the
normal state (e.g. as a result of motion being sensed by the motion detector, gas being
sensed by the gas detector, etc.).
5. EN 50131 standard for Grade 2 consequences
If the installer has configured the control panel in compliance with the EN 50131 standard
requirements for Grade 2:
1. The user codes should be composed of at least 5 characters.
2. The amount of information provided in the keypads by means of the indicators, display
and sound signaling is limited.
3. The quick arming from keypad (without entering the code) is not available.
4. Arming may be impossible, if one of the situations provided for in the standard occurs
(zone violation, trouble).
How requirements of the standard affect the use of the control panel is described in detail
hereunder.
6. Keypads
SATEL offers the following keypads for the PERFECTA 64 M alarm control panel:
PRF-LCD – hardwired keypad with mechanical keys,
INT-KSG2R – hardwired keypad with touch keys,
INT-TSG2 – hardwired touchscreen keypad,

SATEL PERFECTA 64 M 7
INT-TSH2 – hardwired touchscreen keypad,
PRF-LCD-A2 – wireless keypad with mechanical keys and built-in proximity card reader
(ACU-220 / ACU-280 module must be connected),
PRF-LCD-WRL – wireless keypad with mechanical keys (PERFECTA-RF module must be
connected).
The alarm system should include at least one keypad.
Fig. 1. PRF-LCD / PRF-LCD-WRL keypad.
The following manual includes instructions on how to use the wired PRF-LCD keypad and the
wireless PRD-LCD-WRL / PRF-LCD-A2 keypad. For instruction on how to use the
INT-KSG2R, INT-TSG2 and INT-TSH2 keypads, please refer to the manuals included with
these manuals.
The wired keypad is faster to react to user actions than the wireless keypad. The wireless
keypad powered by an external power supply (connected to the APS-055 power supply)
works similarly to the wired keypad. In the wireless keypad powered by the battery, the sleep
mode is started after 20 seconds of inactivity. When the keypad is in the sleep mode,
the display is off and the LED indicators, sound signaling, backlight (of display and keys) and
proximity card reader are disabled. To wake up the keypad, press e.g. .
6.1 Keypads description
6.1.1 LED indicators
LED
Color
Description
green
two LEDs (marked I and II) – ask the installer which LED indicates
the state of which partition
ON – at least 1 partition is armed
flashing – exit delay countdown in at least 1 partition

8 PERFECTA 64 M SATEL
red
two LEDs (marked I and II) – ask the installer which LED indicates
the state of which partition
ON or flashing – alarm or alarm memory in at least 1 partition
The way of presenting the infor
mation is shown graphically below.
The information is presented for 2 seconds and repeated ( – LED
is OFF; – LED is ON). The higher position in the list means the
higher priority of the presented status:
– fire alarm,
–burglary / panic alarm,
– warning alarm,
– tamper alarm,
– fire alarm memory,
– burglary / panic alarm memory,
– warning alarm memory,
– tamper alarm memory.
yellow flashing – trouble or trouble memory
blue
ON – service mode is active and service menu is displayed
flashing –
service mode is active but service menu is hidden or
displayed in another keypad
Information about the armed state can be hidden after a time period defined by the
installer. After you enter the code and press the key, the indicators operate as
shown in the table.
The trouble information is hidden after arming. The installer defines if the trouble
information is hidden after just one of the partitions is armed in any mode or after all
partitions are armed in full mode.
If the Grade 2 option is enabled by installer:
−the LEDs indicate alarms only after entering the code and pressing ,
−flashing of the LED means that there is a trouble in the system, some zones
are bypassed, or that there was an alarm.
6.1.2 Display
The display provides information on the system state and allows you to operate and program
the alarm system. The installer defines the display backlight settings.
The display can operate in one of the following modes:
•normal mode,
•system preview mode.
The installer decides if the system preview mode is available.
The messages about events that occurred in the alarm system are displayed regardless of
the operating mode.
Enter the code and press to open the user menu (p. 15).

SATEL PERFECTA 64 M 9
Normal mode
The following items are displayed in the upper line: date and time in format selected by the
installer or the keypad name.
Press and hold for 3 seconds to switch the display to the system preview mode.
System preview mode
The installer defines the items to be displayed in the system preview mode. This can be:
•text,
•symbol that represents the partition state:
– fire alarm,
– alarm,
– warning alarm,
– tamper alarm,
– full arm,
– night arm,
– day arm,
– entry delay,
– exit delay (less than 10 seconds),
– exit delay (more than 10 seconds),
– fire alarm memory,
– alarm memory,
– warning alarm memory,
– tamper alarm memory,
– not armed.
•symbol that represents the zone state:
– inhibited (not displayed when armed),
– isolated (not displayed when armed),
– first alarm,
– fire alarm,
– alarm,
– tamper alarm,
– tamper (Double EOL zone),
– violated,
– fire alarm memory,
– alarm memory,
– tamper alarm memory,
– normal state.
•symbol that represents the output state:
– deactivated,
– activated.
•information on temperature from an ABAX 2 wireless device,
•date,
•time,
•keypad name,

10 PERFECTA 64 M SATEL
•information on the power consumption of the appliance connected to the ASW-200 smart
plug.
Press and hold for 3 seconds to switch the display to the normal mode.
Messages
The keypad displays the following messages (the higher position on the list, the higher the
priority):
•alarm,
•countdown of entry delay,
•countdown of exit delay,
•alarm memory.
Messages about alarm and alarm memory will not be displayed, if the GRADE 2option
is enabled by the installer.
6.1.3 Keys
Functions of keys
...
press to enter digits (code, partition number, etc.)
press and hold for 3 seconds to view the troubles
press and hold for 3 seconds to turn on/off the keypad CHIME
press and hold for 3 seconds to switch the display between the normal mode
and the system preview mode
press and hold for 3 seconds to trigger the medical alarm
enter the code and press to arm the system in full mode [if the system is
disarmed and t
here is no alarm] or disarm the system and clear the alarm
[if the system is armed and/or there is an alarm]
press and hold for 3 seconds to trigger the panic alarm
enter the code and press to enter the user menu
press and hold for 3 seconds to trigger the fire alarm
used for full arming (see: “Arming”)
used for night arming (see: “Arming”)
used for day arming (see: “Arming”)
used to disarm the system and clear the alarm (see: “Disarming and alarm
clearing”)
Availability of the functions depends on the keypad settings.
The functions of keys in the user menu are described in the “User menu” section (p. 15).
6.1.4 Sound signaling
The installer can disable the sound signaling.

SATEL PERFECTA 64 M 11
Beeps generated when operating
1 short beep – pressing any number key.
3 short beeps – confirmation of:
– starting the arming procedure (there is exit delay in the partition) or arming (there is no
exit delay in the partition),
– disarming and/or alarm clearing,
– selecting the partition which is to be armed or disarmed, or where alarm is to be cleared
– in such a case the keypad is waiting for the code to be entered,
– turning output off,
– turning off the CHIME in the keypad, using the key,
– switching over the display from the normal mode to the system preview mode, and vice
versa, by means of the key.
4 short beeps and 1 long beep – confirmation of:
– turning output on,
– turning on the CHIME in the keypad, using the key.
2 long beeps – incorrect code or pressing the key, if not preceded by entering code or
selecting a partition.
3 long beeps – refusal to carry out a command (the user does not have the required
authority level or the function is not available).
Beeps generated during programming
1 short beep – pressing any number key.
2 short beeps – entering the user menu, submenu or starting a function.
3 short beeps – exiting the service function on pressing the key.
4 short beeps and 1 long beep – termination of the user function on pressing the key,
or quitting the service mode.
2 long beeps – exiting the function on pressing the key, or an unavailable function.
Event signaling
Only installer selected events are signaled.
Duration of the alarm signaling is to be defined by the installer.
If the Grade 2 option is enabled by installer, the keypad will not signal by sounds any
troubles and alarms.
5 short beeps – zone violation (CHIME).
Long beep every 3 seconds, followed by a series of short beeps for 10 seconds
and 1 long beep – countdown of exit delay (if the time is shorter than 10 seconds, only
the final sequence of short beeps will be generated).
2 short beeps every seconds – countdown of entry delay.
2 short beeps every 3 seconds – trouble / trouble memory. The installer defines whether
the signaling is to last until trouble restore, or until trouble review / trouble memory
clearing. When one or both partitions are armed, trouble / trouble memory is not audibly
indicated by the keypad.
Short beep every 0.5 seconds – warning alarm.
Continuous beep – alarm.
Long beep every second – fire alarm.

12 PERFECTA 64 M SATEL
6.2 Codes
The code is used for user authentication. The user needs to enter the code to access the
functions that enable operating the alarm system.
The installer may permit starting some of the functions without using the code.
Do not make your code available to other people.
Using an incorrect code three times may block the keypad for 90 seconds. As long as
the keypad is blocked, entering the correct code is treated as entering an incorrect
code (“Wrong code” message is displayed).
6.2.1 Factory default codes
By default, the following codes are preprogrammed in the control panel:
user 62 code: 1111
service code: 12345
The factory default codes should be changed before you start using your alarm
system (see: “Changing code”).
6.3 Proximity cards
The PRF-LCD-A2 keypad has a built-in proximity card reader. Using the proximity card,
the user can:
•arm the system,
•disarm the system and/or clear alarm,
•control devices connected to the alarm system outputs.
When the PRF-LCD-A2 keypad is powered by the battery, the reader works only if the
keypad is woken up (when the keypad is in the sleep mode, press e.g. to wake it
up).
6.4 Arming
Completion of the steps below will start the arming procedure. The procedure ends when the
exit delay countdown is over (if the procedure is completed successfully, the system
becomes armed – see also “Failure of arming procedure”). If the exit delay time is 0, the
system becomes armed instantly.
The day/night arming modes are available if the installer has defined which zones are
to be active in this armed mode.
During the exit delay countdown, you can leave the partition through an exit route
mapped out by the installer without triggering alarm.
6.4.1 Arming with code
Arming without partition selection
Enter the code, and then press:
- to arm the system in full mode,
- to arm the system in day mode,
- to arm the system in night mode.
In the partitions you have access to, the arming procedure will begin.

SATEL PERFECTA 64 M 13
Arming the selected partition
1. Select the partition which is to be armed (press one of the keys: - partition 1; -
partition 2; - partition 3; - partition 4).
2. Select the arming mode (press one of the keys: - full arming; - day arming;
- night arming). Backlight of the keys will start flashing, which indicates that the code
must be entered.
3. Enter the code.
4. Press or press again the key corresponding to the selected arming mode. In the
selected partition, the arming procedure will begin.
When the quick arming is available, the steps 3 and 4 are skipped.
6.4.2 Arming with proximity card
Decide with the installer which of the following arming methods to use:
•card read (bring the card close to the keys and move it away),
•card hold-down (bring the card close to the keys and hold for about 3 seconds).
All partitions to which you have access will be armed in full mode.
If you arm and disarm the system by bringing the card close to the keypad, disarming
has the priority. This means that if some of the partitions are armed and some are not,
when you bring the card close to the keypad, the partitions will be disarmed.
6.4.3 Quick arming
The installer may permit arming without using the code / proximity card.
1. Indicate the partition(s) to be armed (press one of the keys: - partition 1; -
partition 2; - partition 3; - partition 4; - all partitions).
2. Select the arming mode (press one of the keys: - full arming; - day arming;
- night arming). In the partition(s), the arming procedure will begin.
6.4.4 Arming without delay
If there is nobody in the partition or nobody is leaving the partition which is to be set to the
day / night armed mode, you can arm the partition without exit delay (there will be no exit
delay signaling). When arming the system, press and hold for 3 seconds one of the keys
used to select the arming mode: , or (when arming with code, do it after you
enter the code). The exit delay countdown will not run.
6.4.5 Terminating the exit delay countdown
When the exit delay countdown is running, you can terminate it, thus shortening the exit
delay time. Press and hold , or for about 3 seconds (it is of no consequence
which key you will press).
6.4.6 Service mode and arming
If you try to arm the system when the service mode is active, you will be informed about it by
a message displayed on the keypad. Press if you want to arm the system.
6.4.7 System problems and arming failure
The installer may configure the system so that it is tested for any problems by the control
panel during arming. The possible problems that prevent arming are given below:
•at least one zone that must not be violated during arming (the Priority option has been
enabled for the zone by the installer) is violated in the partition,

14 PERFECTA 64 M SATEL
•at least one alarm zone is violated beyond the exit route in the partition,
•a zone is bypassed in the partition,
•there is tamper in the partition,
•there is trouble in the system.
The check can be performed twice:
•before starting the arming procedure,
•after the exit delay countdown expires.
System not ready and forced arming
If you are trying to arm a partition, but the arming procedure fails to start and the “System not
ready” message is displayed instead, there are some problems in the system that prevent it
from being armed.
When the “System not ready 1=Arm 2=Check”message is displayed, you can:
•press to cancel the arming,
•press to force the arming,
•press to check what has prevented the arming procedure from starting.
When the “System not ready 2= Check”message is displayed, you can:
•press to cancel the arming,
•press to check what has prevented the arming procedure from starting.
If forced arming is not available, you will be able to arm the system only after the
causes that made starting of the arming procedure impossible are eliminated.
List of problems
If, after pressing , it turns out there are several causes that prevent arming, you can
scroll the list using the or keys.
If you want to bypass a violated zone or unbypass a bypassed zone, press (you need
to have the Zone inhibition right). A prompt will appear asking you whether to execute the
function. Press to confirm or to deny.
Having reviewed the list of problems, press to go back to the “System not ready”
message.
Failure of arming procedure
If the system is not armed after the exit delay countdown is over, it means that the control
panel detected a problem that was not there when the exit delay countdown started.
The installer may configure the control panel this way, e.g. to meet the EN 50131 standard
for Grade 2.
Ask the installer how you will be informed of the arming failure.
6.5 Disarming and alarm clearing
If you disarm a partition in which there is an alarm, the alarm will be cleared.
Alarm clearing results in canceling the voice messaging about alarm (unless the
control panel has already managed to notify the users about the alarm).

SATEL PERFECTA 64 M 15
6.5.1 Disarming and clearing alarm with code
Disarming and alarm clearing without partition selection
Enter the code and then press . Disarming / alarm clearing will take place in the
partitions to which you have access.
Disarming and alarm clearing in selected partition
1. Select the partition which is to be disarmed and/or where alarm is to be cleared (press
one of the keys: - partition 1; - partition 2; - partition 3; - partition 4).
2. Press . Backlight of the keys will start flashing, which indicates that the code must be
entered.
3. Enter the code.
4. Press or . Selected partition will be disarmed / alarm will be cleared.
6.5.2 Disarming and clearing alarm with proximity card
Bring the card close to the keys and move it away. All partitions to which you have access
will be disarmed / alarm will be cleared in them.
6.5.3 Alarm clearing without disarming
If the partition is armed and you want to clear the alarm without disarming the partition, enter
the code and then press , or (it is of no consequence which key you will
press). In the partitions you have access to, the alarm will be cleared.
You cannot clear the warning alarm without disarming the system first.
6.6 Triggering the alarm from keypad
The installer can permit triggering alarms from the keypad. To trigger an alarm, do the
following:
fire alarm – press and hold for about 3 seconds,
medical (auxiliary) alarm – press and hold for about 3 seconds,
panic alarm – press and hold for about 3 seconds. The installer defines whether the
loud panic alarm (indicated by the keypads) or the silent panic alarm (not indicated by the
keypads) will be triggered.
6.7 Turning the CHIME on /off
The CHIME is five short sounds by means of which the keypad will inform you e.g. that
a door / window is open. The installer defines which zones of the alarm system can trigger
the CHIME and whether it can be turned on/off by the users.
Press and hold for about 3 seconds to turn on or off the CHIME signaling.
6.8 User menu
Enter the code and press to get access to the user menu. The functions you can run
will be displayed. The list of available functions depends on your rights, as well as on the
state and configuration of the system.
In order to quit the function and/or user menu, press . The keypad will quit the menu
automatically, if 2 minutes have elapsed since the last keypress.

16 PERFECTA 64 M SATEL
Functions of keys in the user menu
...
enter digits, letters and other characters
enable / disable an option
check / uncheck an item
start a function
save changes and quit the function
exit the user menu
quit the function (usually without saving changes)
scroll up the list
move the cursor left
clear the character to the left of the cursor (edit numbers and names)
exit the graphic mode (see: “Graphic mode”)
exit the submenu
move the cursor left
enter the graphic mode (see: “Graphic mode”)
enter the submenu
start a function
move the cursor right
enter the graphic mode (see: “Graphic mode”)
scroll down the list
change the letter case (edit names)
exit the graphic mode (see: “Graphic mode”)
6.8.1 Navigating through the menu and running functions
To navigate throughout the menu, you can use the arrow keys or number shortcuts. You can
also combine the two methods. The cursor shows the submenu you can enter / function
you can run.
Using the arrow keys
1. Use the or key to find the required submenu or function.
2. Press or to open a submenu (use the key to exit the submenu) or run a
function.
Using the number shortcuts
Most submenus and functions are designated by numbers. To find these numbers, refer to
section “User functions list”. Using the number keys, enter the number of submenu / function
to enter the submenu / run the function. You can enter at once a sequence of several digits
(corresponding to successive numbers of submenus and functions) to quickly run the
selected function.
For example, to start the zone inhibiting function, enter the user menu and then press
, where:
- entering the 4.ZONE BYPASSES submenu,
- running the 1.INHIBIT function.

SATEL PERFECTA 64 M 17
Remember that the sequence of digits which starts a function e.g. from the main menu
level will not start the same function from the submenu level.
6.8.2 Data editing
The editing method depends on the type of data. Having completed the editing, press
to save the changes. If you want to exit the function without saving the changes, press .
Selection from the single-choice list
In the lower line of the display, the currently selected item is presented. You can scroll the list
using the and keys.
Selection from the multiple-choice list
In the lower line of the display, one of the items you can choose from is presented. You can
scroll the list using the and keys. The following symbol is situated in the upper
right corner of the display:
– displayed item is selected / option is enabled,
– displayed item is not selected / option is disabled.
Press any number key to change the currently shown symbol for another one.
Press or to enter the graphic mode.
Graphic mode
In the graphic mode you can see on the display the state of up to 32 items simultaneously.
These can be zones, outputs, options, etc. The state is represented by the same symbols as
in the basic mode. No symbol means that this item is unavailable and cannot be edited. The
numbers around the display will help you identify the item. For items 33-64, the cursor is the
flashing symbol. This makes it easier to recognize which items are displayed.
Use the or key to move the cursor. When the cursor is over the item you want to
edit, press any number key. A different symbol will be displayed.
In the graphic mode you can quickly change the status of all available items:
•if you press 3 times within 3 seconds, the symbol will be displayed for all items,
•if you press 3 times within 3 seconds, the symbol will be displayed for all items,
•if you press 3 times within 3 seconds, you will switch all the items to the opposite
state (all the symbols will switch to , and the symbols will switch to ).
If you press when the cursor is on the last available item, the state of the next 32 items
will be displayed. If you press when the cursor is on the first available item, the state of
the previous 32 items will be displayed.
Press or to exit the graphic mode and return to the basic mode.
Entering decimal values
To enter digits, use the number keys. Use the and keys to move the cursor.
In some functions, the key deletes the character on the left side of the cursor.
Entering hexadecimal values
To enter digits, use the number keys. To enter the A, B and C characters, use the key,
and to enter D, E and F, use the key (keep pressing the key until the required character
appears). Use the and keys to move the cursor. The key deletes the
character on the left side of the cursor.

18 PERFECTA 64 M SATEL
Entering names
The characters that can be entered by using the keys are presented in Table 1. Keep
pressing the key until the required character appears. Long press the key to display the digit
assigned to it.
Shown on the right side in the upper line of the display is information about the letter case:
[ABC] or [abc] (it will be displayed after pressing any key and will be visible for a few seconds
after the last keystroke).
Use the and keys to move the cursor. The key deletes the character on the
left side of the cursor.
Key
Characters available after next keystroke
!
?
'
`

"
{
}
$
%
&
@
\
^
|
#
1
a
b
c
2
d
e
f
3
g
h
i
4
j
k
l
5
m
n
o
6
p
q
r
s
7
t
u
v
8
w
x
y
z
9
.
,
:
;
+
-
/
=
_
<
>
(
)
[
]
0
Table 1. Characters available when entering names. The upper case letters are available
under the same keys (to change the letter case, press ).
6.8.3 User functions list
Presented below are all items of the user menu. The menu displayed on the keypad contains
only the items to which you have access, because of the rights granted to you or status of the
system.
Shown in square brackets are key sequences that enable calling the given submenu or
starting the given function from the main menu level.
1.Change code change own code
2.Users
[21] 1.New user add new user
[211] 1.Code enter code
[212] 2.Schedule select user schedule
[213] 3.Partitions select supported partitions
[214] 4.Add key fob add keyfob
[215] 5.Remov.key fob remove keyfob
Button ○select function to run with button ○
Button □select function to run with button □
Button ▲select function to run with button ▲
Button ■select function to run with button ■
Button ●select function to run with button ●