Satel INTEGRA Plus User manual

Firmware version 1.15
Alarm Control Panels
USER
MANUAL
SATEL sp. z o.o.
ul. Budowlanych 66
80-298 Gdańsk
POLAND
tel. + 48 58 320 94 00
www.satel.eu
integra_plus_u_en 04/16

WARNING
Before you start using the control panel, please read carefully this manual in order to avoid
mistakes that can lead to malfunction or even damage to the equipment.
Changes, modifications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
The INTEGRA Plus control panels should only be connected to the analog subscriber lines.
In case of changing the analog line to the digital one, it is necessary to contact the alarm
system installer.
Pay special attention if the telephone line used by the control panel is frequently busy and/or
failures are reported, concerning the line and/or monitoring. Report such situations to the
alarm system installer immediately.
To ensure adequate protection, the alarm security system must be in good working order,
therefore SATEL recommends that it be regularly tested. The control panel is equipped with
a number of self-diagnostic functions which, when properly configured by the installer, ensure
control over correct functioning of the system.
The alarm security system cannot prevent burglary, assault or fire from happening, but it
guarantees that in case of emergency measures will be taken to reduce the possible damage
(the alarm will be signaled optically and acoustically, appropriate services will be notified,
etc.), which may deter the potential burglars.
SATEL's goal is to continually upgrade the quality of its products, which may result in some
changes of their technical specifications and firmware. The current information on
the introduced modifications is available on our website.
Please visit us at:
http://www.satel.eu
The declaration of conformity may be consulted at www.satel.eu/ce
Factory default codes:
Service code: 12345
Object 1 master user (administrator) code: 1111
The following symbols may be used in this manual:
- note;
- caution.

CONTENTS
1. General.............................................................................................................................3
2. Technical reliability of the alarm system ...........................................................................3
3. Alarm system operating costs...........................................................................................3
4. Authorization of users.......................................................................................................4
4.1 Authorization with two identifiers ...............................................................................4
4.2 Factory default codes ................................................................................................4
4.3 Operation under duress.............................................................................................5
5. Operating the alarm system by means of LCD keypad.....................................................5
5.1 Keypads description ..................................................................................................5
5.1.1 LCD display ........................................................................................................5
5.1.2 LED indicators ....................................................................................................7
5.1.3 Keys ...................................................................................................................8
5.1.4 Built-in proximity card reader..............................................................................8
5.1.5 Sound signaling..................................................................................................8
5.2 [Code] – arming / disarming menu.......................................................................... 9
5.2.1 Arming menu ....................................................................................................10
5.2.2 Disarming menu ...............................................................................................10
5.3 [Code] – user menu ............................................................................................. 10
5.3.1 Functions list ....................................................................................................10
5.3.2 Starting functions..............................................................................................13
5.3.3 Menu shortcuts.................................................................................................14
5.3.4 Entering data by means of the LCD keypad..................................................... 14
5.3.5 Description of user functions ............................................................................16
5.4 Arming .....................................................................................................................21
5.4.1 Full arming without partition selection ..............................................................21
5.4.2 Full arming the selected partitions....................................................................22
5.4.3 Arming in the selected mode............................................................................22
5.4.4 Quick arming ....................................................................................................22
5.4.5 Denial of arming ...............................................................................................22
5.4.6 Failure of arming procedure .............................................................................23
5.4.7 Shortening the exit delay time ..........................................................................23
5.5 Disarming and alarm clearing..................................................................................23
5.5.1 Alarm clearing without disarming......................................................................23
5.6 Two-code arming / disarming ..................................................................................23
5.7 Triggering the alarm from keypad............................................................................24
5.8 Users .......................................................................................................................24
5.8.1 User types ........................................................................................................25
5.8.2 Adding new user...............................................................................................26
5.8.3 Edit user ...........................................................................................................27
5.8.4 Removing a user .............................................................................................. 27
5.8.5 Adding proximity card / DALLAS iButton ..........................................................27
5.8.6 Adding keyfob...................................................................................................28
5.8.7 Removing keyfob..............................................................................................29
5.9 Master users (administrators)..................................................................................29
5.10 Zone bypassing .......................................................................................................29
5.10.1 Zone inhibiting ..................................................................................................29
5.10.2 Zone isolating ...................................................................................................30
5.10.3 Unbypassing.....................................................................................................30
5.11 Viewing the event log .............................................................................................. 31

2 User Manual SATEL
5.11.1 Viewing all events.............................................................................................31
5.11.2 Viewing the events required for Grade 3 ..........................................................31
5.11.3 Viewing the selected events .............................................................................31
5.11.4 Way of presenting events .................................................................................31
5.12 Programming the partition timer...............................................................................32
5.13 Zone testing.............................................................................................................33
5.14 Outputs control ........................................................................................................34
5.14.1 Controlling the MONO SWITCH type of output....................................................34
5.14.2 Controlling the BI SWITCH type of output............................................................34
5.14.3 Controlling the REMOTE SWITCH type of outputs .................................................34
5.14.4 Controlling the roller shutter outputs.................................................................35
6. Using the partition keypad ..............................................................................................35
6.1 Description of partition keypads...............................................................................36
6.1.1 LED indicators ..................................................................................................36
6.1.2 Keys .................................................................................................................36
6.1.3 Built-in proximity card reader ............................................................................36
6.1.4 Sound signaling ................................................................................................36
6.2 Functions available from the partition keypad..........................................................37
6.2.1 [Code] ...........................................................................................................37
6.2.2 [Code] ............................................................................................................38
6.2.3 Quick arming ....................................................................................................38
6.2.4 Triggering the alarm from keypad.....................................................................38
6.2.5 Silencing the alarm sound at the keypad..........................................................38
6.2.6 Code changing .................................................................................................38
7. Using the entry keypad ...................................................................................................38
7.1 LED indicators .........................................................................................................39
7.2 Sound signaling .......................................................................................................39
7.3 Functions available from the entry keypad ..............................................................39
8. Using the code lock.........................................................................................................39
8.1 Description of code locks.........................................................................................40
8.1.1 LED indicators ..................................................................................................40
8.1.2 Keys .................................................................................................................40
8.1.3 Sound signaling ................................................................................................40
8.2 Functions available from code lock..........................................................................41
9. Confirming voice messaging...........................................................................................41
10. Call answering and telephone control.............................................................................42
10.1 Answering phone calls.............................................................................................42
10.2 Telephone control ....................................................................................................42
10.3 Audio alarm verification ...........................................................................................43
11. Operating the alarm system by means of keyfob............................................................43
12. Manual update history.....................................................................................................45
13. Brief description of operating the system from keypad ...................................................46

SATEL INTEGRA Plus 3
1. General
This manual applies to the control panels of the INTEGRA Plus series:
– INTEGRA 64 Plus
– INTEGRA 128 Plus
– INTEGRA 256 Plus
Thank you for choosing the product offered by the SATEL Company. Wishing you full
satisfaction with the choice you made, we are always ready to provide you with professional
assistance and information on our products.
The SATEL Company is manufacturer of a broad range of devices dedicated for use in
security alarm systems. Further information is available on our website www.satel.eu or at
the points of sale offering our products.
It is recommended that that the installers prepare their own user manual for the alarm
system installed by them. The manual must include all changes and modifications in
relation to the factory default settings.
The installer should train the users in the rules of operating the alarm system.
2. Technical reliability of the alarm system
A failure of any component of the alarm system will result in deterioration of the level of
protection. Unfortunately, the devices which are installed outside (e.g. the outdoor sirens) are
exposed to the adverse effects of weather. During storms, the devices connected to the
electrical system or telephone line are vulnerable to damage as a result of atmospheric
discharge.
The control panel is provided with a number of safeguards and automatic diagnostic features
to test the system performance. Detection of irregularities is signaled e.g. by the LED on
the keypad. You should immediately respond to such a signal, and, if necessary,
consult the installer.
In addition, some features designed for testing the alarm system are available in the control
panel. They make it possible to check the detectors, sirens, telephone communicators, etc for
correct functioning. Only regular testing and inspection of the alarm system will allow
you to keep a high level of protection against intrusion.
It is recommended that the installer, at the request of the user, carry out periodic
maintenance of the alarm system.
It is in the interest of the user to anticipate and plan in advance the procedures in case an
alarm is set off by the control panel. It is important to be able to verify the alarm, determine its
source and take appropriate actions (e.g. evacuation in the event of a fire alarm).
3. Alarm system operating costs
The control panel can inform the users and the monitoring station about the status of
protected facility. Realization of these functions by means of the phone line or GSM means
financial costs. The amount of the costs incurred depends on the amount of information sent.
A failure of telephone links, as well as an incorrect programming of the control panel, may
result in increased costs (due to making of excessive number of calls).
Please inform the installer, which is a priority: to deliver information at any cost, or to prevent
excessive costs. For example, after an event code has failed to be sent successfully to the

4 User Manual SATEL
monitoring station, the control panel may repeat attempts every few minutes to send the code
or to cease the attempts to send the code until a next event occurs.
4. Authorization of users
Operation of the alarm system is possible after the user authorization, which allows the
control panel to verify that the user is authorized to perform the given operation. The
authorization can be done on the basis of:
code,
proximity card (125 kHz passive transponder, which can be in the form of card, tag, etc.),
DALLAS iButton (chip),
keyfob.
You can not assign the same identifier (code, proximity card, DALLAS iButton or
keyfob) to two users.
For safety reasons, different people should not use the same identifier.
The installer can configure the panel so that it will not accept codes that contain less
than three digits (e.g. 1111 or 1212) or consist of consecutive digits (3456).
The installer may permit the use of certain functions without the need for user
authorization.
Using an invalid code, proximity card or DALLAS iButton three times may:
trigger an alarm,
block the keypad / reader for 90 seconds.
4.1 Authorization with two identifiers
The INT-KLCDR and INT-KLFR keypads and the INT-SCR multifunction keypads have a
built-in proximity card reader. The installer can configure these devices so that the user has
to use two identifiers for authorization: the code and the card. The function to be executed
after the authorization depends on the second identifier:
– code – whether it will be confirmed by using the key or the key,
– card – whether it will be presented only or held.
4.2 Factory default codes
By default, the following codes are preprogrammed in the control panel:
service code: 12345
object 1 master user (administrator) code: 1111
The factory default codes make it possible to assign individual codes to consecutive persons
who are to use the alarm system (see: “Users” p. 24).
The factory default codes should be changed before you start using your alarm system
(CHANGE OWN CODE function available in the user menu).
The control panel can inform the user that the code change is necessary, if the code is
known to other users.

SATEL INTEGRA Plus 5
The master code should not be used on a daily basis because of the risk of its being
captured. It is recommended that the administrator enter for himself an ordinary user's
code.
4.3 Operation under duress
When acting under duress, the DURESS type code must be used instead of the normal user
code (see “User types” p. 25).
5. Operating the alarm system by means of LCD keypad
SATEL offers the following keypads for INTEGRA Plus control panels:
INT-TSG – touchscreen keypad,
INT-TSI – touchscreen keypad,
INT-TSH – touchscreen keypad,
INT-KSG – LCD keypad with touch keys,
INT-KLCD – LCD keypad with mechanical keys,
INT-KLCDR – LCD keypad with mechanical keys and built-in proximity card reader,
INT-KLCDK – LCD keypad with mechanical keys,
INT-KLCDL – LCD keypad with mechanical keys,
INT-KLCDS – LCD keypad with mechanical keys,
INT-KLFR – LCD keypad with mechanical keys and built-in proximity card reader.
The keypads are available in a variety of color options for the enclosure, display and key
backlight. The color variant is indicated by the additional designation in the keypad name
(e.g. INT-KLCD-GR – green display and key backlight; INT-KLCD-BL – blue display and key
backlight).
5.1 Keypads description
The INT-TSG, INT-TSH, INT-TSI and INT-KSG keypads are described in separate
manuals, which are delivered with these keypads.
5.1.1 LCD display
The display facilitates communication between the user and the alarm system, clearly
indicating the system status. The functions available to the user are presented on the display.
The display backlight can be used, if needed.
In standby mode, the display shows:
– in the upper line – the date and time in the format defined by the installer,
– in the lower line – the keypad name or state (status) of selected partitions (to be defined
by the installer).
The installer can configure the keypad so that when you press the 9 key for approx. 3
seconds, the display will enter the partition state presentation mode. The status of
partitions operated by the keypad (including those from which alarm is signaled on the
keypad) is presented by means of symbols. The display will return to the standby mode after
you press the 9 key for approx. 3 seconds again.
If some predefined events occur, additional messages may appear on the display (e.g.
arming, disarming, auto-arm delay countdown, entry/exit delay countdown, alarm, etc.).

6 User Manual SATEL
Fig. 1. Keypads with flap.
Entering the user code, i.e. the user authorization, will open a menu containing the functions
that are available to the user. The functions are presented in two lines. The currently selected

SATEL INTEGRA Plus 7
function is indicated by the arrow on the left-hand side. How the function related information
is presented depends on the specific character of the given function.
The way of display backlighting is programmed by the installer.
INT-KLCDS INT-KLCDL
Fig. 2. Keypads without flap.
5.1.2 LED indicators
LED Color Function description
green ON – all keypad operated partitions are armed
blinking – some keypad operated partitions are armed or exit delay
countdown is running
red ON or blinking – alarm or alarm memory
yellow blinking – trouble or trouble memory
green blinking – service mode is entered
green if zone status is being presented or the keypad is switched to graphic
programming mode (see: “Selection from the multiple-choice list”
p. 15), two LEDs indicate which data set is being displayed (see:
table 2)
Table 1. Description of keypad LEDs.
LED
Data type left side/upper right side/lower Information
OFF OFF numbers 1-32
OFF ON numbers 33-64
ON OFF numbers 65-96
Zones/Outputs
ON ON numbers 97-128 / 97-256
OFF OFF system addresses 0-31 (00-1F HEX)
Expanders OFF ON system addresses 32-63 (20-3F HEX)
Table 2. Information presented by the LEDs.
Information about the armed state can be extinguished after a time period defined by
the installer.

8 User Manual SATEL
If the installer has enabled the GRADE 3option:
the LEDs provide information about alarms only after the code has been
entered and confirmed with the key,
blinking of the LED means that there is a trouble in the system, some zones
are bypassed, or that there was an alarm.
5.1.3 Keys
The keys designated with digits and letters enable entering the code and data, when using
the functions available in the menu. Additionally, if you press and hold down the selected digit
keys for approx. 3 seconds, you can (if the keypad has been so configured by the installer):
1- check the state of zones,
4- check the state of partitions,
5- view the alarm log,
6- view the trouble log,
7- view the current troubles,
8- turn on/off CHIME in the keypad,
9- toggle the display between the standby mode and partition state display mode.
The other keys enable you to:
- enter the user menu (after entering the code),
- cancel the started operation.
or - arm / disarm and clear alarm (after entering the code),
- start the selected function,
- confirm the entered data.
- navigate through the display (scroll through the displayed messages, functions
and options, and move the cursor),
- run the installer selected functions (after entering the code).
- trigger the fire alarm.
- trigger the medical (auxiliary) alarm.
- trigger the panic alarm.
5.1.4 Built-in proximity card reader
The INT-KLCDR and INT-KLFR keypads can be operated by means of proximity cards
(proximity tags or other 125 kHz passive transponders). The installer defines which functions
can be executed after presenting or holding the card.
5.1.5 Sound signaling
Beeps generated when operating
The installer can disable the sound signaling.
1 short beep – pressing any number key.
2 short beeps – confirmation of command execution, signaling of entering the user menu,
submenu or function.

SATEL INTEGRA Plus 9
3 short beeps – signaling of:
– starting the procedure of arming (there is exit delay in the partition) or arming (there is
no exit delay in the partition),
– disarming and/or alarm clearing,
– turning output off,
– turning off the CHIME in the keypad, using the 8 key,
– toggling the display between the standby mode and the partition status presentation
mode, using the 9 key,
– exiting the function and returning to the menu after confirmation of the data entered.
4 short beeps and 1 long beep – signaling of:
– turning output on,
– turning on the CHIME in the keypad, using the 8 key,
– ending the function and exiting the user menu after confirmation of the data entered.
1 long beep – signaling of:
– violated/ bypassed zones when arming,
– fault of the vibration detector (10. 24H VIBRATION type zone was not violated during the
vibration detector test run upon starting the arming procedure).
2 long beeps – invalid code/card, function not available or exiting the function without
confirmation of the data entered (e.g. by using the key).
3 long beeps – unavailable function.
Events signaled by sounds
Only installer selected events are signaled.
Alarms are being signaled throughout the time programmed by the installer.
5 short beeps – zone violation (CHIME).
Long beep every 3 seconds, followed by a series of short beeps for 10 seconds
and 1 long beep – countdown of exit delay (if the time is shorter than 10 seconds, only
the final sequence of short beeps will be generated).
A sequence of 7 beeps of diminishing duration, repeated every few seconds –
countdown of auto-arming delay.
2 short beeps every seconds – countdown of entry delay.
2 short beeps every 3 seconds – signaling a new trouble.
Continuous beep – alarm.
Long beep every second – fire alarm.
5.2 [Code] – arming / disarming menu
Information given in the section below do not apply to users having the SIMPLE USER
right (see p. 25).
After you enter the code and confirm it with the key:
– a message on the need to change the code or a service note may be displayed,
– alarm will be cleared – if the user is authorized to clear the alarm and there is an alarm
in the system,
– one partition will be disarmed – if the user is authorized to disarm the partition, has
access to only one partition operated from the keypad and that partition is armed, or has
access to many partitions, but only one partition is armed,

10 User Manual SATEL
– one partition will be armed – if the user is authorized to arm the partition, has access to
only one partition operated from the keypad and that partition is disarmed,
– the arming/disarming menu will be displayed.
5.2.1 Arming menu
The arming menu will be displayed if:
– the user is authorized to arm the partition,
– the user has access to a number of partitions operated from the keypad,
– none of the partitions accessible to the user is armed,
– there is no alarm.
Two functions are available in the menu:
Arm all arming all partitions
Arm selected arming selected partitions
5.2.2 Disarming menu
The disarming menu will be displayed if:
– the user is authorized to disarm the partition,
– the user has access to a number of partitions operated from the keypad,
– at least two partitions accessible to the user are armed.
Two functions are available in the menu:
Disarm all disarming all partitions
Disarm selected disarming selected partitions
5.3 [Code] – user menu
After you enter the code and confirm using the key, the user menu will be displayed. The
list of available functions depends on the user authority level, as well as the system status
and configuration. In order to exit the user menu, press the key. The keypad will quit the
menu automatically, if 2 minutes have elapsed since the last keypress.
Upon entering the code and confirming with the key, a message about the need to
change the code or a service note may be displayed.
5.3.1 Functions list
The functions available after entering the service code have been highlighted with
white text against black background. Highlighted with a frame are functions available
to the administrators.
View clear. al. view cleared alarms from selected partition zones
System reset restore system after verified alarm
Disarm disarm selected partitions
Clear alarm clear alarm
Clear other al. clear alarm in other objects
Abort voice m. cancel telephone messaging
Arm arm selected partitions
Arm (2 codes) start two code arming
Disarm (2codes) start two code disarming
Defer auto-arm postpone the auto-arming
Set auto-arm d. set auto-arming postpone time

SATEL INTEGRA Plus 11
Arming mode select arming mode
Cancel 1st code cancel consent to two code arming/disarming
Change own code change own code
Change tel.code change own telephone code
Change prefix
Prefix normal set normally used prefix
Prefix duress set duress prefix
Recall time set time to remind of the need to change prefix
Users
New user add new user
Code set code
Telephone code set telephone code
Partitions assign partitions available to the user
Type select type of code
Schedule select time schedule
Existence time set code validity time
Bypass time set bypass time
Rights assign rights
Keypads etc. assign modules available to the user
New prox. card add proximity card
Rem. prox. card remove proximity card
New DALLAS add DALLAS iButton
Remove DALLAS remove DALLAS iButton
New RX key fob add 433 MHz keyfob
Rem. RX key fob remove 433 MHz keyfob
Button 1 assign function to keyfob button 1
Button 2 assign function to keyfob button 2
Button 3 assign function to keyfob button 3
Button 4 assign function to keyfob button 4
Button 1 and 2 assign function to combination of keyfob buttons 1 & 2
Button 1 and 3 assign function to combination of keyfob buttons 1 & 3
Events (RX) set event generating rules
New ABAX keyfob add keyfob supported by ABAX system
Rem.ABAX keyfob remove keyfob supported by ABAX system
Button 1 assign function to keyfob button 1
Button 2 assign function to keyfob button 2
Button 3 assign function to keyfob button 3
Button 4 assign function to keyfob button 4
Button 5 assign function to keyfob button 5
Button 1 and 5 assign function to combination of keyfob buttons 1 & 5
Events (ABAX) set event generating rules
Confirm. (ABAX) set confirmation rules
Name program user name
Edit user edit existing user
[select user]
[list of parameters identical as in case of a new user]
Remove user remove user
Masters
New master add new master
Code set code
Rights assign rights
Keypads etc. assign modules available to the master
New prox. card add proximity card

12 User Manual SATEL
Rem. prox. card remove proximity card
New DALLAS add DALLAS iButton
Remove DALLAS remove DALLAS iButton
New RX keyfob add 433 MHz keyfob
Rem. RX keyfob remove 433 MHz keyfob
Button 1 assign function to keyfob button 1
Button 2 assign function to keyfob button 2
Button 3 assign function to keyfob button 3
Button 4 assign function to keyfob button 4
Button 1 and 2 assign function to combination of keyfob buttons 1 & 2
Button 1 and 3 assign function to combination of keyfob buttons 1 & 3
Events (RX) set event generating rules
New ABAX keyfob add keyfob supported by ABAX system
Rem.ABAX keyfob remove keyfob supported by ABAX system
Button 1 assign function to keyfob button 1
Button 2 assign function to keyfob button 2
Button 3 assign function to keyfob button 3
Button 4 assign function to keyfob button 4
Button 5 assign function to keyfob button 5
Button 1 and 5 assign function to combination of keyfob buttons 1 & 5
Events (ABAX) set event generating rules
Confirm. (ABAX) set confirmation rules
Name set master name
Edit master edit existing master
[select master]
[list of parameters identical as in case of a new master]
Remove master remove master
Zone bypasses
Inhibit temporary zone bypass
Isolate permanent zone bypass
Set time set control panel clock
System state check troubles / check system state
Events
Selected
Select events select type of events to be viewed
Select part. select partitions from which events are to be viewed
View view selected events
View Grade3 view events required for Grade 3
All view all events
Grade3 view events required for Grade 3
Reset zones reset 43. RESETABLE POWER SUPPLY type outputs
Clr.latch.outs clear latched outputs
Fin.f.door open end door fire opening
Change options
Keypad chime turn on/off CHIME in keypad
Outputs chime block zone violation signal. on 11. CHIME type outputs
Timers edit timers
Temperatures edit temp. thresholds and hysteresis for 120. THERMOSTAT type out.
Part. timers program partition timers
No exp.tamp.al. block expander tampers
Perm.serv.accs. enable/disable permanent installer access
Serv. can edit make user editing available to installer
Serv. ArmDis... make system control available to installer

SATEL INTEGRA Plus 13
Perm.DLOADX acc enable/disable permanent DLOADX access
DLOADX IP set address of computer with DLOADX program
GUARDX IP set address of computer with GUARDX program
Erase s.message erase service note
Tests
Partitions check current state of partitions
Zones check current state of zones
Supply voltages check module supply voltage
Radio devices check radio signal level for wireless devices
Temperatures check temperatures measured by ATD-100 detectors
Zones test
New Burglary zones start new test for burglary zones
Fire/tech.zones start new test for fire and technical zones
One zone start new test for single zone
View results view test results
Finish test abort test
Clear results clear test results
Battery test test battery and 60. TECHN.-BATTERY LOW zones
Manual tr. test start manual test transmission
Station 1A test start test transmission to station 1 – main phone number
Station 1B test start test transmission to station 1 – backup phone number
Station 2A test start test transmission to station 2 – main phone number
Station 2B test start test transmission to station 2 – backup phone number
Messaging test start messaging test
Answering test display information on answered tel. call
Prox. card test check proximity card number
CA-64 PTSA test start mimic board test
View masters view master users
Keypad name display keypad name
File in DLOADX display inf. on DLOADX program file with control panel data
Panel version display information on control panel firmware version
STM prg.version display information on the STM processor program version
IP/MAC ETHM-1 disp. inf. on ETHM-1 / ETHM-1 Plus module IP and MAC address
Modules version display information on module firmware version
Time synchron. start time synchronization
Service access set installer access time
Open door open selected door controlled by system
Outs control control outputs
Service mode start service mode
Take SM over take over service mode
Downloading
Start DWNL-RS start local programming
Finish DWNL-RS finish local programming
Start DWNL-MOD. start communication via external modem
Start DWNL-TEL start communication via 300 bps modem
ETHM-1 – DLOADX start communication via Ethernet with DLOADX program
ETHM-1 – GUARDX start communication via Ethernet with GUARDX program
5.3.2 Starting functions
1. Using the and keys, find the required submenu or function. The currently selected
submenu or function is indicated by the arrow ( ) on the left-hand side.

14 User Manual SATEL
2. Press the or key to enter the submenu (the key allows to exit the submenu) or
start the function.
5.3.3 Menu shortcuts
Support for the user menu shortcuts can be disabled by the installer.
You can use shortcuts for quick access to some menu elements (submenus, functions).
Press the suitable digit key (or combination of keys) to enter a submenu or start a function.
Shown below is the list of submenus and functions available by using shortcuts. The
shortcuts are shown in square brackets.
[1] Change own code
[2] Users
[21] New user
[22] Edit user
[23] Remove user
If the installer is not authorized to edit the users, the shortcuts beginning with the digit
2 will allow the installer to start the function from the MASTERS submenu.
[4] Zone bypasses
[41] Inhibit
[42] Isolate
[5] Events
[51] Selected events
[52] All events
[6] Set time
[7] System state
[8] Outputs control
[9] Service mode
[0] Downloading
[01] Start DWNL-RS
[02] Finish DWNL-RS
[03] Start DWNL-MOD.
[04] Start DWNL-TEL
[07] ETHM-1 – DLOADX
[08] ETHM-1 – GUARDX
5.3.4 Entering data by means of the LCD keypad
Data are saved to the control panel if you press the key (in some keypads, the key is
also available, whose function is exactly the same). The key enables exiting the function
without saving any changes.
Described below are general rules for entering data, however they may be different as
regards some functions.
Selection from the single-choice list
Shown in the upper line of display is description of the function, and in the lower one – the
currently selected item. You can scroll through the list of items, using the direction keys: 
(down) and (up). The and keys are not used.

SATEL INTEGRA Plus 15
Selection from the multiple-choice list
The functions that allow you to make multiple choice can be identified by an additional
symbol situated at the right-hand side of the display:
– displayed item is selected / option is enabled,
– displayed item is not selected / option is disabled.
Pressing any digit key (for some functions, this does not work with the key 0) will change the
currently displayed symbol to the other one. To scroll through the list of items, use the key
(down) or the key (up). For some functions, pressing the key 0 will allow you to enter the
number of item to be edited (e.g. number of zone to be bypassed / unbypassed). This will
speed up search.
For some functions, pressing the or key will switch the keypad into the graphic
programming mode. The and symbols are used to present on the display the current
status of up to 32 items available in the given function (these can be e.g. zones, outputs,
timers, etc.). Additionally, in case of zone bypassing, the symbol is used. The key moves
the cursor to the right, and the key to the left. If the list of items is longer than 32, pressing
the key when the cursor is placed over the last item will display the next list, and pressing
the key when the cursor is placed over the first item will display the previous list (see also
description of the LEDs, p. 7). Pressing the key 0, 1 or 2 three times in the graphic mode
within 3 seconds will have the following effect:
000 - the symbol will be displayed at all available items,
111 - the symbol will be displayed at all available items,
222 - reversal of the selection made: the symbol will be displayed at all items where
the symbol was displayed, and the symbol where the symbol was displayed.
On pressing the or key, the keypad will return to the text mode.
Fig. 3. Example of how information is presented in the graphic programming mode. The blank
fields are not available for editing.
Entering decimal and hexadecimal values
Digits are entered by pressing the suitable keys. Characters from A to F are available under
the keys with numbers 2 and 3. Keep pressing the keys until the required character appears.
Entering names
Press the particular keys until the required character appears. The characters available in the
keypad are shown in Table 3. Hold down the key to display the digit assigned to the key.
Shown on the left side in the upper line of the display is information about the letter case:
[ABC] or [abc] (it will be displayed after pressing any key and will be visible for a few seconds
after the last keystroke).
The key moves the cursor to the right, and the key – to the left. The key deletes the
character on the left side of the cursor.

16 User Manual SATEL
Key Characters available after next keystroke
1 ! ? ' ` " { } $ % & @ \ ^ | # 1
2 abc2
3 def3
4 ghi4
5 jkl5
6 mno6
7 p q r s 7
8 t u v
8
9 wxyz9
0 . , : ; + - / = _ < > ( ) [ ] 0
Table 3. Characters available when entering names. The upper case letters are available
under the same keys (to change the letter case, press key.
5.3.5 Description of user functions
View cleared alarms – available, if the user did not view the violated zones after alarm
clearing. It allows to check which zones triggered the alarm. After completion of the
viewing, the function is no longer available.
System reset – available to the installer, if the option REQUIRED SYSTEM RESET AFTER VERIFIED
ALARM is enabled, and a verified alarm took place. After occurrence of the verified alarm, it
is necessary to reset the system by means of this function, in order to make re-arming
possible.
Disarm – allows to disarm the partitions accessible to the user from the given keypad.
Clear alarm – allows to silence the alarm.
Clear other alarms – allows to silence the alarms from other objects, to which the user has
normally no access.
Abort voice messaging – terminates the telephone messaging.
The messaging can be cancelled automatically together with alarm clearing. The
messaging cancellation rules are defined by the installer.
Arm – allows to arm the partitions accessible to the user from the given keypad.
Arm (2 codes) – allows to initiate arming of the partitions which require entering 2 codes.
Disarm (2codes) – allows to initiate disarming of the partitions which require entering 2
codes.
Defer auto-arming – available when auto-arming delay countdown is running. It allows to
postpone by a programmed time period the auto-arming of the partition in which the auto-
arming delay countdown is running. Entering just zeros will block the auto-arming function
(until the next auto-arming time).
Set auto-arming delay – available when the auto-arming delay is programmed for at least
one partition and the auto-arming delay countdown is not currently running in that partition.
It allows to postpone by a programmed time period the auto-arming of the partition.
Arming mode – allows to select the arming mode which is to be used (the shortcut key is
shown in square brackets):
[0] full arming (to be used after everybody has left the protected area),

SATEL INTEGRA Plus 17
[1] full arming + bypasses (allows the users to stay in the protected area) – the zones for
which the BYPASSED IF NO EXIT option is enabled by the installer will be bypassed,
[2] arming without interior (allows the users to stay in the protected area):
interior zones (3. INTERIOR DELAYED zone type) will be disarmed,
violating the exterior zone (8. EXTERIOR zone type) will trigger a silent alarm,
violating another alarm zone will trigger a loud alarm.
[3] arming without interior and without entry delay (allows the users to stay in the
protected area – to be used when nobody else is to enter the protected area) – this
arming mode is similar to the previous one, but the delayed zones operate as the
instant ones (no entry delay).
Cancel 1st code – if the partition is armed/disarmed by means of two codes and the first
code has already been entered, the user can still cancel the consent to arming/disarming.
Change own code – allows the user to change his/her own code.
Change telephone code – allows the user to change his/her own telephone code.
Change prefix – available to the administrator, if the use of prefixes in the system has been
made available by the installer (the prefix length has been defined). It enables to program
the prefixes and the time to remind about the need to change the prefix. Each code will
have to be preceded by a prefix:
normal – for everyday use. By default, it consists of a suitable number of digits 0 (e.g. if
the determined prefix length is 4, the default prefix is 0000),
DURESS – for use, when the user has been forced to enter the code. Using the code will
trigger a silent alarm. By default, it consists of a suitable number of digits 4 (e.g. if the
determined prefix length is 3, the default prefix is 444).
Users – the following functions are available in the submenu:
New user – allows to create a new user (see: “Adding new user” p. 26).
Edit user – allows to edit the existing users (see: “Edit user” p. 27).
Remove user – allows to remove the existing users (see: “Removing a user”p. 27).
The administrator defines whether the installer is to have access to the USERS
submenu (SERV.CAN EDIT option in the CHANGE OPTIONS submenu).
Masters – the submenu provides the following functions available to the installer:
New master – allows to create a new administrator.
Edit master – allows to edit the existing administrators.
Remove master – allows to remove the existing administrators.
Zone bypasses – the following functions are available in the submenu:
Inhibit – allows to temporarily bypass the zones (see: “Zone inhibiting” p. 29).
Isolate – allows to permanently bypass the zones (see: “Zone isolating” p. 30).
If the GRADE 3option has been enabled by the installer, the ISOLATE function is only
available to the installer.
Set time – allows to program the control panel clock. The data are entered in the following
format:
time – hour:minute:second,
date – day:month:year.
System state – allows to view the troubles and, if the GRADE 3global option has been
enabled by the installer, also the alarms and bypassed zones, as well as to check the
partition status.

18 User Manual SATEL
Events – the submenu contains functions which allow to view the events saved to the control
panel memory (see: “Viewing the event log”p. 31).
Reset zones – running the function will result in a temporary deactivation of the
43. RESETABLE POWER SUPPLY type outputs, thus making it possible to reset the alarm
memory for detectors supplied from those outputs (e.g. fire detectors).
Clear latched outputs – allows to turn off some of the control panel outputs for which the
LATCH option is enabled, as well as the 9. DAY ALARM, 12. SILENT ALARM
and 116. INTERNAL SIREN type outputs.
Fin.f.door open – restores the normal operating mode in all modules executing the access
control functions (in case of fire, the doors controlled by these modules may be
automatically unlocked).
Change options – the following functions are available in the submenu:
Keypad chime – allows to turn on/off the CHIME in the keypad. The CHIME is five short
sounds by means of which the keypad will inform you e.g. that a door / window is open,
when the system is disarmed. The installer defines which zones of the alarm system
can trigger the CHIME.
Outputs chime – allows to block the chime signal from selected partitions on the
11. CHIME type output.
Timers – allows to program parameters of the timers controlling the 120. THERMOSTAT type
outputs, and other timers, the editing of which is permitted by the installer.
Temperatures – allows to edit the temperature thresholds and hysteresis for
120. THERMOSTAT type outputs.
Partition timers – allows to program the partition timers (see: “Programming the partition
timer”p. 32).
No expanders tamper alarms – allows to temporarily disable the expansion module
tamper supervision. In case of any problems with the expansion modules, report the fact
to the installer.
Permanent service access – the option is available to the master user (administrator). If
enabled, the installer has permanent access to the alarm system, which, among other
things, enables the control panel to be programmed by using LCD keypad or DLOADX
program.
Enabling PERMANENT SERVICE ACCESS option will clear the installer access time
programmed with the SERVICE ACCESS function. On the other hand, programming the
installer access time will disable the PERMANENT SERVICE ACCESS option.
Service can edit – the option is available to the master user (administrator). If it is
enabled, the installer can add, edit and delete users in the administrator's object.
Service arm/disarm/clear/bypass – the option is available to the master user
(administrator). If it is enabled, the installer can arm/disarm the system, clear alarms
and bypass zones in the administrator object.
Permanent DLOADX access – the option is available to the master user (administrator).
If it is enabled, the control panel can be programmed by means of the DLOADX
program, irrespective of whether or not the installer has access to the alarm system.
DLOADX IP – enables programming the address of the computer, on which the DLOADX
program is installed. The address must be set if the control panel is to initiate
communication with the DLOADX program through Ethernet, using the TCP/IP
protocols (see: description of the ETHM-1 – DLOADX function, available in the
DOWNLOADING submenu). It can be entered as a name or IP address.
GUARDX IP – enables programming the address of the computer, on which the GUARDX
program is installed. The address must be set if the control panel is to initiate