Satel INTEGRA User manual

Alarm Control Panels INTEGRA
GDAŃSK
integra_u_e 08/07
USER
MANUAL

WARNING
In order to avoid any operational problems with the control panel, it is recommended that you
become familiar with this manual before you start using the equipment.
Making any construction changes or unauthorized repairs is prohibited. This applies, in
particular, to modification of assemblies and components. Maintenance and/or repair
operations should be performed by authorized personnel (i.e. the installer or factory service).
The control panel should be connected to analog lines only. Connecting its telephone circuit
to a digital network (e.g. ISDN) may cause damage to the equipment. In case of changing the
analog line to the digital one, it is necessary to contact the alarm system installer.
Pay special attention if the telephone line used by the control panel is frequently busy and/or
failures are reported concerning the line and/or monitoring. Report such situations to the
alarm system installer immediately.
CAUTION!
The alarm system is fitted with a battery. After expiry of its lifetime, the battery must not be
thrown away, but disposed of as required by the existing regulations (European Directives
91/157/EEC and 93/86/EEC).
The latest EC declaration of conformity and product approval certificates
are available for downloading on website www.satel.pl
The INTEGRA alarm control panels meet requirements as per CLC/TS 50131-3, Grade 3,
and have been certified by Det Norske Veritas Certification AS, Norway.
Environmental class of the INTEGRA series control panels: II.

Changes in the INTEGRA control panels with firmware in version 1.05
Support of new
modules INT-SCR-BL – multifunctional keypad which can work as a partition keypad (identified as INT-S/SK), partition keypad with reader
(identified as INT-SCR) or entry keypad (identified as INT-ENT)
INT-ORS – DIN-rail outputs expander
INT-IORS – DIN-rail zones/outputs expander
INT-RX – 433 MHz remote key fob operation expander
Timers Defining the armed mode to be activated by timer: fully armed, armed
without interior or armed without delayed.
Users A remote key fob can be assigned to each user.
A zone which will be violated by pressing a button / combination of
buttons can be assigned to each key fob button / two button
combinations (1 & 2 and 1 & 3).
Arming The arming procedure in LCD keypad has been modified. If arming is
impossible (because of zone violation, tamper, trouble, etc.) and the
keypad has displayed a list of causes for such a situation, you can
make another attempt to rearm by pressing the [#] key (without
reentering the access code or selecting the armed mode status and
partitions).
User functions The ZONES TEST function has been modified by adding the option to
terminate the test before the programmed time has expired.
The TIME SYNCHRONIZATION function has been added.

User Manual INTEGRA
2
CONTENTS
1. GENERAL............................................................................................................................4
2. ABOUT THIS MANUAL............................................................................................................4
3. TECHNICAL RELIABILITY OF THE ALARM SYSTEM......................................................................4
4. ALARM SYSTEM OPERATING COSTS.......................................................................................5
5. INTEGRA CONTROL PANEL .................................................................................................5
5.1 BASIC FUNCTIONS OF THE CONTROL PANEL .................................................................................5
5.2 CONTROL PANEL PERFORMANCE ................................................................................................6
6. OPERATION OF INTEGRA CONTROL PANEL ..........................................................................7
6.1 BASIC INFORMATION ..................................................................................................................7
6.2 LCD KEYPADS........................................................................................................................... 8
6.2.1 Display...............................................................................................................................................10
6.2.2 Keys...................................................................................................................................................10
6.2.3 LED indicators...................................................................................................................................11
6.2.4 Audible signals ..................................................................................................................................12
6.3 USING LCD KEYPAD................................................................................................................. 12
6.3.1 Selecting functions from menu..........................................................................................................14
6.3.2 Entering data.....................................................................................................................................14
6.3.3 Graphic mode....................................................................................................................................15
6.3.4 Reading alarm source name.............................................................................................................16
6.3.5 Proximity card reader (INT-KLCDR-GR/INT-KLCDR-BL only).........................................................16
6.4 PARTITION KEYPADS ................................................................................................................ 17
6.5 MULTIFUNCTIONAL KEYPAD WITH PROXIMITY CARD READER........................................................ 21
6.5.1 Work in the partition keypad mode (INT-S/SK).................................................................................21
6.5.2 Operation in partition keypad mode with proximity card reader (INT-SCR)......................................21
6.5.3 Operation in entry keypad mode (INT-ENT) .....................................................................................23
6.6 CODE LOCKS ........................................................................................................................... 24
6.7 PROXIMITY CARD AND DALLAS CHIP READER............................................................................ 26
6.8 CODES AND USERS .................................................................................................................. 27
6.9 PREFIXES................................................................................................................................28
6.10PROXIMITY CARDS/DALLAS CHIPS ........................................................................................... 28
6.10.1 Assigning proximity cards/DALLAS chips.........................................................................................28
6.10.2 Deleting cards/DALLAS chips...........................................................................................................29
6.11SYSTEM ARMED MODE.............................................................................................................. 29
6.12ALARMS .................................................................................................................................. 31
6.13ALARM MESSAGING BY TELEPHONE........................................................................................... 32
6.14ANSWERING PHONE CALLS ....................................................................................................... 33
6.15OTHER FUNCTIONS USING TELEPHONE LINE............................................................................... 34
7. USER FUNCTIONS..............................................................................................................34
7.1 MAIN MENU ............................................................................................................................. 34
7.1.1 User function menu...........................................................................................................................35
7.2 DESCRIPTION OF USER FUNCTIONS........................................................................................... 40
View cleared alarms .................................................................................................................................40
System reset.............................................................................................................................................40
Disarm.......................................................................................................................................................40
Clear alarm ...............................................................................................................................................40
Clear other alarms....................................................................................................................................40
Abort voice messaging .............................................................................................................................40
Arm ...........................................................................................................................................................40
Arm (2 codes) ...........................................................................................................................................40
Disarm (2codes) .......................................................................................................................................41
Defer auto-arming.....................................................................................................................................41
Set auto-arming delay...............................................................................................................................42
Arming mode ............................................................................................................................................42
Cancel 1st code........................................................................................................................................42
Change own code.....................................................................................................................................42
Change prefix ...........................................................................................................................................43

INTEGRA SATEL 3
Masters.....................................................................................................................................................43
Users ........................................................................................................................................................43
Zone bypasses .........................................................................................................................................46
Set time.....................................................................................................................................................46
Troubles....................................................................................................................................................47
Events.......................................................................................................................................................47
Reset zones..............................................................................................................................................48
Clear latched outputs................................................................................................................................48
Change options.........................................................................................................................................49
Tests.........................................................................................................................................................50
Service access..........................................................................................................................................52
Open door.................................................................................................................................................52
Outputs control .........................................................................................................................................52
Service mode............................................................................................................................................53
Take SM over ...........................................................................................................................................53
Downloading.............................................................................................................................................53
8. CONFORMANCE TO CLC/TS 50131-3 REQUIREMENTS.........................................................54
9. APPENDIX A......................................................................................................................55
10. APPENDIX B......................................................................................................................57
11. APPENDIX C .....................................................................................................................58
12. HISTORY OF THE MANUAL UPDATES.....................................................................................64

User Manual INTEGRA
4
1. GENERAL
Thank you for choosing the product offered by the SATEL Company. High quality, large
number of functions and simple operation are the main advantages of our alarm control
panel. Wishing you full satisfaction with the choice you made, we are always ready to provide
you with professional assistance and information on our products. Please note that, besides
the control panels, SATEL manufactures many other components of alarm systems. Detailed
information on our full offer can be found nationwide at retail dealers offering our products, on
website www.satel.pl.
2. ABOUT THIS MANUAL
This Manual allows you to familiarize yourself with the basic operation of modules designed
to control the operation of alarm systems based on the INTEGRA control panels and with the
functions performed by these panels. The INTEGRA includes four alarm control panels:
INTEGRA 24, INTEGRA 32, INTEGRA 64 and INTEGRA 128. All of them feature identical
functionality and differ in their technical parameters and in their designation for small,
medium-size or large facilities.
The part “Operation of INTEGRA Control Panel" of this Manual describes the modules that
control operation of the control panel and how they should be used. It also presents some
functions related to the alarm system operation, and includes some basic information on
functioning of the system and use of the telephone line by the control panel.
The part “User Functions" of this Manual contains full specification of functions accessible
from the alphanumeric LCD keypad.
The text in this Manual contains some technical terms: for explanation please refer to
APPENDIX B at the end of this Manual.
Please read carefully the entire manual since familiarity with the control panel functions will
allow you to take full advantage of the equipment possibilities. The control panel can perform
functions that are nor related directly to monitoring. The use of all control panel functions and
the operational efficiency of the entire system depend to a large extent on its installation
method and its programming by the installer. The control panel may perform its functions in
many ways, which are defined when installing and programming the system. Therefore, you
should obtain from the installer more detailed information on how the alarm system operates
and how it should be used.
All situations in which the way of the control panel operation depends on previous installer
decisions (made at the time of programming) are additionally marked by inserting the PROG
symbol (after description of the situation).
The term "service", as used in this manual, refers to the user who takes care of the alarm
system and is authorized to use the service code. He can be installer, maintenance
technician, security guard employed for protection of the facility, etc.
This manual applies to the control panel program version 1.05.
3. TECHNICAL RELIABILITY OF THE ALARM SYSTEM
The alarm system is composed of technical devices whose reliability is vital for the
effectiveness of the facility protection. The elements of the alarm system are exposed to the
impact of various outside factors, including weather conditions (outside sirens), atmospheric
discharges (overhead telephone lines, power lines, outside sirens), mechanical damage
(keypads, detectors, etc.). Only routine inspection of the alarm system operation will make it
possible to keep a high level of burglary and fire protection.

INTEGRA SATEL 5
The control panel is provided with a number of safeguards and auto-diagnostic functions for
testing the system reliability. The control panel signals detection of a problem by lighting up
the LED labeled [TROUBLE] on the keypad. You should immediately respond to such
a signal, and, if necessary, consult the installer.
It is necessary to periodically carry out a functional test of the alarm system. Check that the
control panel responds to violation of individual detectors, that their fields of view are not
masked, that there is a reaction to opening protected windows, and that sirens and telephone
messaging work normally.
Detailed instructions on the system testing should be provided by the installer. It is
recommended that the installer carry out periodic maintenance of the alarm system, when
ordered by the user.
It is in the user's best interest to anticipate and plan beforehand appropriate procedures in
case the control panel signals an alarm condition. It is important that he should be able to
verify the alarm, determine its source on the basis of keypad information, and take
appropriate measures, e.g., to organize evacuation.
4. ALARM SYSTEM OPERATING COSTS
The main task of the control panel is signaling and efficient reporting of alarm situations and,
in the case of the monitoring function, providing the monitoring station with real-time
information about the protected facility status. Realization of these functions, based on the
use of telephone line, entails financial costs. Generally, the level of costs incurred by the
alarm system owner depends on the amount of information the control panel has to transfer
to the monitoring station. A failure of the telephone links, as well as incorrect programming of
the control panel, may to a large degree increase these costs. Such a situation is usually
related to an excessive number of connections made.
The installer can adjust functioning of the alarm system to the specific conditions and kind of
the protected site, however it is the user who should decide if his or her priority is transferring
information at any price, or, if some technical problems occur, the control panel is allowed to
skip some events, the reception of which has not been confirmed by the monitoring station.
5. INTEGRA CONTROL PANEL
The INTEGRA alarm control panel is designed for the security supervision in small, medium-
size and large facilities. The supervision is not limited to protection against burglary, but it
may also include monitoring of the facility for correct functioning for 24 hours a day. The
status of the alarm system is monitored on a continuous basis. Violation of any alarm system
component triggers the so-called tamper alarm. The control panel responds to signals from
individual detectors and decides whether to signal the alarm or not. Since various detectors
may be connected to the control panel, the type and way of alarming depends on the way of
control panel programming (the control panel may respond in one way to a signal from fire
detector and in another way to a signal from a water level detector).
The control panel makes it possible to group zones and detectors connected to them into so-
called partitions, and to freely determine which partition is to be supervised (armed).
Activation of any detector from such a group (hereinafter called “zone violation") may trigger
an alarm. A great advantage of the control panel is its high flexibility in determination which
partitions may be armed at the moment.
5.1 BASIC FUNCTIONS OF THE CONTROL PANEL
•signaling burglary, attack, fire, technical and auxiliary alarms,

User Manual INTEGRA
6
•monitoring – communication with the monitoring stations (real time sending detailed
information on selected events in the protected facility),
•telephone messaging on alarms – either with the use of a voice message or to a pager,
•answering phone calls (this function is protected with a separate code) which makes it
possible to:
−inform the user on the system status,
−control via telephone some of the control panel functions, which were programmed by
the service,
•real-time printout of information regarding all or selected events that have occurred in the
alarm system with the use of an external printer,
•control of access to the facilities through doors provided with electromagnetic locks,
•monitoring individual alarm system components (e.g. power supplies, batteries, wiring) for
correct operation.
5.2 CONTROL PANEL PERFORMANCE
•operated from keypads provided with LCD text display (2x16 characters) to facilitate the
use of the system,
•operated from the cellular phone used as a remote keypad (provided that the ETHM-1
module is installed in the security system),
•operation and supervision of the system by means of the computer (GUARDX program,
and also the internet browser, provided that the ETHM-1 module is installed in the security
system),
•installer defined descriptions of zones and partitions for easy identification of the alarm
source,
•visible system date and time to better check the real-time dependent functions for correct
operation,
•optional display of the status of partitions (up to 16 selected or all),
•available viewing of the alarm/trouble log (or detailed memory of all events) with textual
description of event, name of zone, module, partition or the user who operates the system,
together with accurate time of the event occurrence,
•monitoring, depending on the mainboard, of up to 8 independent alarm systems and up to
32 armed independently partitions,
•control of individual system parts from independent keypads (maximum 8 LCD keypads
and 64 partition LED keypads for the INTEGRA 64 and the INTEGRA 128),
•individual control of the output types of MONO SWITCH,BI SWITCH,REMOTE SWITCH,
SHUTTER UP and SHUTTER DOWN,
•dynamically changeable menu (dependent on authority level) to provide access to
a number of user functions, the selection made by accepting the suitable function from the
list shown on the LCD keypad screen,
•key shortcuts to facilitate calling frequently used functions,
•service note shown on LCD display.

INTEGRA SATEL 7
6. OPERATION OF INTEGRA CONTROL PANEL
6.1 BASIC INFORMATION
LCD keypads and partition keypads are mainly used for operating the alarm system based
on the INTEGRA control panel. Additionally, the control panel supervises and registers usage
of code locks as well as proximity card and Dallas chip readers, installed at the doors in
individual spaces of the facility. Partition keypads may be also used as code locks.
The LCD keypads may be used to control many partitions in various objects. The partition
keypads control just one partition. Individual control devices are assigned by the installer to
specified partitions. The users may operate the control panel only if they have access to
partitions operated by particular keypads. This means that the partitions assigned to the user
at the stage of creating/editing a new user (see DESCRIPTION OF USER FUNCTIONS ÆUSERS)
must correspond to those operated by the keypad. The list of partitions operated by individual
LCD keypads is defined by the installer.
Example: LCD keypad controls partitions 1,2,3,4,5 and 6. The user has access to partitions
5,6,7 and 8. Hence, using this LCD keypad he can control partitions 5 and 6.
A similar principle applies to partition keypads, code locks, proximity card readers and
DALLAS chip readers. With keypads, the user can control the partitions he has access to,
and he may open the doors with code locks and proximity card/DALLAS chip readers, to
opening of which he has been authorized. The installer defines the list of users of individual
partition keypads, code locks and readers (separately for each module).
The access to the control panel control functions and the vital information on the system
status are protected with a CODE (the code is a combination of 4 to 8 digits). In systems
which require enhanced protection, it is possible to extend the code by a prefix (1 to 8 digits),
periodically changed by the object master user code.
It is possible to obtain some information on system and call some functions without entering
any code, but by holding down (for approximately 3 seconds) one of the keypad keys PROG.
INFORMATION FUNCTIONS
[1] – viewing zones status,
[4] – viewing partitions status,
[5] – viewing alarms log,
[6] – viewing troubles memory,
[7] – viewing current troubles,
[8] – switching on/off chime signal in LCD keypad,
[9] – toggling partition display modes: selected / all,
X– viewing names of partitions, where alarm occurred (also W) (press the Xkey quickly
to activate viewing names of partitions selected for display),
S– viewing names of zones which caused an alarm (also T)
ALARM FUNCTIONS
– AUXILIARY alarm (for example, calling for medical aid)
– FIRE alarm
– PANIC alarm
Functions of arrows and keys from 1 to 9 are accessible from LCD keypad only, while the
other functions (alarm) may be accessible from each keypad installed in the system (LCD
keypad, partition keypad, code lock) PROG. Thus activated viewing functions provide
information on all partitions operated with specific LCD keypads. They are also accessible
from the user menu (see: Description of user functions – TESTS,EVENTS,TROUBLES,CHANGE

User Manual INTEGRA
8
OPTIONS), however, when called via the user menu they only provide information on the
partitions accessible to the user who called that function.
It is recommended that the above way of calling functions be only available in
LCD keypads fully protected against unauthorized access.
If the function of partition status display is activated, the key 9 changes the display operating
mode. The following display options are provided:
•date and status of any selected 16 partitions,
•status of all partitions in the system (no date and/or time indication). The partition numbers
correspond to those provided around the display.
The “PANIC alarm" (called by ) may be signaled externally, in much the same way as the
“burglary" alarm (buzzers, lights); it can also be set not to activate any external signaling but
function as a “silent PANIC alarm" PROG.
The installer may also enable the function of quick arming of certain partitions (i.e. QUICK
ARM) so that it can be called by pressing in turn the [0] and [#] keys.
[0][#] quick arming of partitions. This function may be accessible from LCD/partition
keypads. When called from LCD keypad, the function may arm several partitions;
when called from partition keypad – only the partition, which the partition keypad is
assigned to.
Also, if you simultaneously hold down both Sand Tkeys (for approx. 40 seconds) the
keypad processor will restart and display the version numbers of keypad and control panel
programs.
6.2 LCD KEYPADS
SATEL offers the following LCD keypads for INTEGRA control panels:
−INT-KLCD-GR/INT-KLCD-BL
−INT-KLCDR-GR/INT-KLCDR-BL
−INT-KLCDK-GR
−INT-KLCDL-GR/INT-KLCDL-BL
−INT-KLCDS-GR/INT-KLCDS-BL
These keypads differ by their size, shape and current consumption. The INT-KLCDR-
GR/INT-KLCDR-BL keypad incorporates a built-in proximity card reader. Most of the keypads
are available in two versions: with green or blue display and key backlight of the same color.
Designation of the models with green display ends with "GR" letters, and that of the models
with blue display – with "BL" letters.

INTEGRA SATEL 9
Fig. 1. View of INT-KLCDR-GR keypad.
Fig. 2. View of INT-KLCDS-GR keypad.

User Manual INTEGRA
10
Fig. 3. View of INT-KLCDK-GR keypad.
6.2.1 Display
The LCD keypad comes with a large LCD display (2 x 16 characters) with permanent or
temporary backlighting; the temporary backlighting is activated either by pressing any key or
by violation of any zone (service setting).
The backlighting (including illumination of the keys) may be automatically switched off in the
case of the control panel 230V AC voltage loss.
During normal operation, the display shows the current date and time, it can also
permanently show the keypad name. The format of displayed information is defined by the
installer. The lower display line can be used to show the current status of selected partitions
(up to 16), the displayed symbols being as described in the TESTS function.The first
character in the lower line (from left) shows the status of the lowest number partition, as
selected by the installer. The following numbers show information on the partitions in the
ascending order.
The LCD display can also show important information transmitted by the service using the
so-called SERVICE MESSAGE. The displayed text can contain up to 29 characters and can be
displayed either permanently, or for a specified period of time. It can be visible either to all
users, or only to some of them after entering the access code.
6.2.2 Keys
Situated under the display are keys (illuminated in much the same way as the keypad
screen), which are used for:
•entering codes,
•moving through menu and selecting appropriate functions from the list,
•entering data for called functions.

INTEGRA SATEL 11
The letters provided on numerical keys can help to memorize the access code by associating
it with a particular word (e.g. the code "[7][8][2][7][8]" corresponds to the word "START"). The
[#] and [ok] keys are electrically connected to each other and may be used interchangeably.
Therefore, if using the [#] key is mentioned elsewhere in the following part of this manual, it
should be understood that the [ok] key may also be used instead.
6.2.3 LED indicators
Arranged at the LCD display are 6 LEDs which indicate current status of the system.
– ALARM (red) – permanent lighting of the LED indicates alarm. After expiry of the alarm
time, the blinking LED means alarm memory. The LED is going off after deletion of
alarm (see: ALARMS).
Note: The LED may not signal alarms in the armed mode if the installer has enabled the
option DO NOT SHOW ALARM IF ARMED, as required by the CLC/TS 50131-3 standard.
– TROUBLE (yellow) – blinking light indicates that a technical trouble has occurred in the
system. Emergency situations causing this LED to light up are described further in this
Manual (see Description Of User Functions ÆTROUBLES). The LED goes temporarily
off when the LCD keypad is in partially armed mode (at least one partition accessible
to the given LCD keypad is armed) or in fully armed mode (all partitions accessible to
the LCD keypad are armed) PROG. The LED is blinking until the troubles are viewed
and the trouble memory is reset (the option TROUBLE MEMORY UNTIL REVIEW enabled) or
until the trouble cause stops (the option TROUBLE MEMORY UNTIL REVIEW disabled)
PROG.
– ARMED (green) – the LED is blinking when some partitions are armed and lights
steadily when all partitions operated by the keypad are armed.
– SERVICE (green) – the LED is blinking when the control panel is in the service mode
(function only available to the user having a service code).
Note: The service mode limits normal operation of the control panel. Alarms from most
zones (except for the following types: PANIC, 24H CASH MACHINE, and 24H VIBRATION)
as well as tamper alarms are not signaled. To restore normal operation of the control
panel, you should exit the service mode, because the control panel will not
automatically return to its normal operating mode.
– GROUP (two green LEDs) – used in graphic mode functions to indicate which data set
is currently displayed. The LEDs can show the number of zones or outputs, or indicate
the corresponding expander bus. (See: Description of user functions ÆBYPASS ZONES;
TESTS). LED
INDICATION left side/upper right side/lower DESCRIPTION
OFF OFF group 1; numbers 1–32 (n)
OFF ON group 2; numbers 33–64 (32+n)
ON OFF group 3; numbers 65–96 (64+n)
ZONES/
OUTPUTS ON ON group 4; numbers 97–128 (96+n)
OFF OFF
first expander bus
bus 1 numbers (addresses) 0-31 (DEC)
system addresses 00–1F (HEX)
EXPANDER
BUSES OFF ON
second expander bus
bus 2 numbers (addresses 0-31 (DEC)
system addresses 20–3F (HEX)
n – number of LCD keypad field

User Manual INTEGRA
12
6.2.4 Audible signals
When using the keypad the following signals, characteristic of some situations, can be heard
PROG.
•One long beep – refusal of arming - the zone, which shouldn't be violated at the time of
arming, is violated (PRIORITY option), there was a trouble with the battery, expander, or
keypad. The refusal includes all zones selected for arming. Also, warning of the system
failure - prior to arming.
•Two long beeps – the code not recognized by the control panel; function not accessible;
wrong data; acknowledgement of canceling the selected function (after pressing [*] on the
keypad); pressed key is not active; card code not recognized.
•Three long beeps – the code is recognized, but the function called is not accessible (for
example, temporary partition blocking is activated or the user has no access to partitions
operated from the keypad).
•Two short beeps – selection accepted – entering more detailed menu level.
•Three short beeps – acknowledgement of arming or disarming.
•Four short and one long beeps – acceptance of execution of the selected function.
•Three pairs of short beeps – it is necessary to change the code (for example, another
user, when changing his code, indicated the combination of digits identical with that in the
given user code; the code validity is expiring).
Additionally, the following situations may be signaled:
•Alarm in partition – continuous beep for the total alarm duration (time programmed by
service).
•Fire alarm – series of long beeps every second for the total alarm duration.
•Countdown of entry delay – 2 short beeps every second.
Note: The signaling of entry delay countdown by 2 short beeps refers to the LCD keypads
type INT-KLCD-GR/BL and INT-KLCDR-GR/BL with firmware in version 1.05, and to
the keypads type INT-KLCDL-GR/BL, INT-KLCDS-GR/BL and INT-KLCDK-GR with
firmware in version 6.05. In keypads with earlier firmware versions, the entry delay
countdown is signaled by short beeps every 3 seconds.
•Countdown of exit delay – long beeps every 3 seconds, completed with a series of
short beeps (for 10 seconds) and a single long beep. The way of “exit delay" signaling
informs that the countdown is ending prior to arming.
•Auto arming delay countdown (timer-controlled partitions) – a series of 7 sounds (of
diminishing length).
•Chime in LCD keypad – five short beeps – this is a response to activation of some
detectors when the zone is disarmed.
6.3 USING LCD KEYPAD
Operation of the system from LCD keypad starts with entering the user CODE and pressing
the key marked [#], [ok] or [*]. The control panel response (accessible functions) after
pressing the [#] or [ok] key is different than that after pressing [*].
[CODE][#] or [CODE][ok] you get access to functions of arming/disarming type,
[CODE][*] you get access to all functions in the user menu to which the user is authorized.
Example: When you enter your code and press [#], the control panel will make available the
functions of partition arming (provided that no partition, operated from the LCD keypad, is
already armed) or disarming (if any of partitions is armed). In the event of alarm occurrence
in the system, the control panel may cancel this alarm and provide access to the function of
partition disarming (if the user is authorized to do that). When the function of telephone
messaging is activated – the Clear voice messaging function may appear in menu. When the

INTEGRA SATEL 13
user has access to a single partition only, entering the code and pressing [#] results in
immediate arming or disarming (if the partition is armed).
Entering the code and pressing [*] displays the list of functions accessible from the User
Menu. The User Menu provides also access to the following functions: Arming and Disarming
(if some partitions are armed). When all partitions are armed, the function Arming will not be
accessible.
Note: Entering a wrong code (not recognized by the panel) three times may:
−trigger an alarm PROG,
−block a keypad for 90 sec. After this time each next wrong code entering will block
the keypad PROG.
The specific feature of the control panel is the dynamic changing of the accessible menu,
dependant on the system programmed parameters, as well as on the authorization level of
the user who entered the code. The user get access only to those function in the user menu
to which he is authorized.
In order to call some functions more quickly, the user can use some SHORTCUT KEYS.
Having called the menu ([CODE][*]), press the suitable numerical key – the control panel will
enter directly the called function.
The following user functions are assigned to the corresponding keys:
[1] Change own code
[2] Users/Masters
[3] none
[4] Zone bypasses
[5] Events
[6] Set time
[7] Troubles
[8] Outputs control
[9] Service mode
[0] Downloading
The installer can assign functions to the arrow keys to facilitate the everyday operation of
the system. These functions are called in the following way:
[CODE] S
[CODE] W
[CODE] X
[CODE] T
One of the following functions can be assigned to each arrow:
−Arming (full)
−Arming (without interior zones)
−Arming (without interior zones, without entry delay)
−Disarming
−Alarm clearing
−Zones bypassing
−Bypass clearing
−Output MONO ON
−Output BI switch state
−Output BI ON
−Output BI OFF

User Manual INTEGRA
14
For each of the functions the installer determines the number of partition, zone or output it
refers to. The user, who wants to perform the given function must have an appropriate
authority level and access to the selected partitions.
The control panel may fail to arm the system, if the selected partitions contain a violated zone
which is monitored during arming.
All user functions, which are accessible from LCD keypad, are described in section
"Description Of User Functions".
6.3.1 Selecting functions from menu
When the control panel has recognized the code, the first user function (from all functions
accessible at the moment) will appear in the upper line of the display. You can move through
the list of functions made available by the control panel by pressing Sand T, and select the
required item from the list (single-selection list) by pressing [#] or X. If the selected function
requires making further selection (submenu, options), the next list appears on the display,
which allows you to select required item in a similar way.
Some functions may need selection of a few items from the list (multi-selection list). To do
that, scroll the list by pressing Sand Tkey and "mark" all items in the list, which should be
selected. The item is marked by pressing any numeric key, then the symbol appears in the
upper display corner next to the text. Press the numeric key again to cancel you selection.
By scrolling the list upwards or downwards (the list contents is displayed cyclically), you can
see all the items and check the selections. Pressing the [#] or Xkey accepts the selection
(execution of function may be confirmed with a beep), and the control panel returns to
previously displayed menu or displays a corresponding message and returns to the basic
status (waiting for code). Then, current date and time is displayed. Date and time display
format is defined by the installer PROG.
There is a control panel setting option which activates the procedure of double confirmation
of some user functions. After pressing the [#] or Xkey (normal mode of selecting a function),
a prompt appears on the screen asking to confirm the function, together with information:
1=Yes. Press the key with digit 1to confirm this function. This procedure is a safeguard
against accidental double pressing [#] (or X) and execution of function, which should not yet
be executed. The description of user functions in this Manual relates to situation when this
option is switched off.
If you want to give up the selection of function after opening the User Menu, press the [*] key.
If no keypad button is pressed (within 2 minutes) after menu opening, the control panel will
automatically close this menu and return to its basic status.
6.3.2 Entering data
Some functions require entering a new code or user name. The way of entering the new data
that relate to system users is described below. When changing the code, the control panel
does not show the old code, unless the user has not yet changed the code assigned to him
by the person introducing him into the system. However, the old name always is shown on
the display when the old name is being changed. The entered user name appears in
selection lists, printouts and when viewing the events log in the computer.
•new code, time limit: numeric data are entered by means of the numeric keys. The arrow
keys are used for modification of numbers to be entered. Below the text field, where the
entered digits appear, a cursor (dash) can be seen. The Wand Xarrows are used for
moving the cursor to show the successive digits. Press the key with a digit to enter the
given digit at the left side of cursor, and press the Sarrow to delete the digit at the left
side of cursor. The Tarrow changes the cursor type – a blinking dark rectangle appears.
This type of cursor allows changing the digit above the dash to the digit entered from the
keyboard. Press the Tkey again to return to the previous cursor type.

INTEGRA SATEL 15
•user name: the user name is entered by means of numeric keys which in this case
change their meaning and enable text data (letters) to be entered into the control panel.
Table 2 contains characters accessible from the keypad. By pressing the numeric key
again will cyclically change the available characters. The new user name is entered by
changing the factory-entered name. You may delete the old name by pressing the S
arrow key (each single press deletes the character at the left side of the cursor). Press the
Tarrow key to enter space at the left side of the cursor; use the Wand Xarrow keys to
move the cursor under the user name to highlight the position which can be changed. To
change the character at the position indicated by the cursor, repeatedly press the key with
the proper digit until the proper character appears. Then, move the cursor to the next
position and repeat the procedure.
Pressing [#] accepts the entered data.
Key Characters accessible after key pressing
1 1 ! ? ' ` " { } $ % & @ \ ^ | #
2 A a B b C c 2
3 D d E e F f 3
4 GgHhIi4
5 JjKkLl5
6 M m N n O o 6
7 P p Q q R r S s 7
8 T t U u V v 8 O
9 W w X x Y y Z z 9
0 0 . , : ; + - / = _ < > ( ) [ ]
Table 2. Characters accessible in the text mode of data entering.
6.3.3 Graphic mode
The functions regarding selection of partitions, zones and outputs provide also another way
of multiple selection from the list (for example, selection of partitions for arming). It is the so-
called graphic mode. When the selection list is already open, you can enter this mode by
pressing the Xor Wkeys. Dots will appear on the keypad display under the number of each
accessible partition (numbers 1–32 around the display). The dash under the dot (cursor)
indicates which item can be selected. Use the Xand Wkeys to move the cursor to the
required item. Pressing any numeric key causes the symbol to appear at the item selected.
Press the numeric key again to deselect the item. By pressing Sor Tthe previous display
mode (with name) will be restored.
Likewise, when selecting zones or outputs, the dots stand for the available zones or outputs,
but if their number exceeds 32, they are displayed in groups, 32 items in each group (up to 4
groups with 32 zones/outputs each for INTEGRA 128). The number of the currently displayed
group is indicated by two lit LEDs labeled [GROUP] (see description of the LEDs, p. 11).
To calculate the number of the zone/output indicated by the cursor, add, respectively, 32, 64
or 96, depending on the number of displayed group, to the number placed on the keypad
glass next to the cursor.
In the graphic mode, the keys 0, 1 and 2 have special editing functions assigned to them.
Pressing one of them three times results in:
[0][0][0] – deletion of all selected items ( symbol OFF)
[1][1][1] – selection of all available items ( symbol ON)
[2][2][2] – negation of state of all available fields (inversion of selection)

User Manual INTEGRA
16
6.3.4 Reading alarm source name
The installer can enable the function of displaying the name of alarm source on the LCD
keypad, without necessity of entering the code. In such a case, the partition or zone name is
displayed on the keypad screen when an alarm occurs. If there are a few alarm causes, you
may scroll through the zone names which caused the alarm, and the names of partitions
where the alarm is (or was) signaled. The Wand Xarrow keys allow viewing partition names
(if the alarm occurred in several partitions), while the Sand Tkeys allow viewing the names
of zones which caused the alarm. These names (entered by the installer) are displayed
cyclically in the lower keypad screen line, in the order corresponding to the numbers of
zones/partitions in the system. To view the names of alarm sources when the alarm signaling
is over, press and hold down the corresponding arrow key.
6.3.5 Proximity card reader (INT-KLCDR-GR/INT-KLCDR-BL only)
The INT-KLCDR-GR/INT-KLCDR-BL keypads with built-in proximity card reader make
available a few extra functions, including:
•card code readout when the card is assigned to its user (functions: NEW USER,EDIT USER),
•performance of function specified by the installer,
•registering the guard round.
The keypad can respond to the card being briefly presented to the reader or to its being
presented and held for a few seconds (aprox. 3sec.). It is also possible to perform two
consecutive functions which are assigned to bringing the card closer and holding it at the
reader. This feature makes it possible, by a single use of the card, to perform rather
complicated functions which might be time-consuming when called from the keypad.
List of functions which can be called by using the proximity card:
1. no function– no response
2. as code *– enters the user functions menu
3. as code # – calls the function of selecting partitions to be armed or disarmed
(arming/disarming if the selection list for the particular code is limited to just one partition)
4. as code Ç– performs function assigned to the arrow key (p. 42)
5. as code Å– performs function assigned to the arrow key
6. as code Æ– performs function assigned to the arrow key
7. as code È– performs function assigned to the arrow key
8. open door (entry) – controls the electromagnetic door lock (generates a USER ACCESS
event)
9. open door (exit) - controls the electromagnetic door lock (generates a USER EXIT event)
10.2 long sounds – signals reading of the card code
11.1 short beep – signals that the card code has been read
Notes:
•Selecting the function 2 or 3 to be started by PRESENT CARD will block access to the HOLD
CARD.
•The 8 and 9 functions require that the installer select the door to be opened by the keypad.
It is possible to control any door handled by the system (i.e. opened by code locks,
partition keypads or expanders of proximity card readers).
•Two long beeps can also mean readout of a card with unknown code.
•Readout of an unknown (wrong) code, if repeated three times, may generate a panel
recorded event or an alarm PROG. It can also block the reader in the keypad for 90 sec.

INTEGRA SATEL 17
6.4 PARTITION KEYPADS
SATEL offers the following partition keypads for INTEGRA control panels:
−INT-S-GR/INT-S-BL
−INT-SK-GR
These keypads differ by size and shape. The keypads are available with green or blue
backlighting of the keys. Designation of the models with green display ends with "GR" letters,
and that of the models with blue display – with "BL" letters. The backlighting may be
permanent or time-controlled (switched on automatically).
Fig. 4. INT-S-GR/INT-S-BL partition keypad.

User Manual INTEGRA
18
123
456
789
0#
Fig. 5. INT-SK-GR partition keypad.
The partition keypads are provided with LED indicators:
– ALARM (red) – permanent lighting of the LED means alarm. After the alarm time
expires, blinking of the LED indicates the alarm memory. The LED goes off after the
alarm is cleared (see: ALARMS).
Note: The LED may not signal alarms in the armed mode if the installer has enabled the
option DO NOT SHOW ALARM IF ARMED, as required by the CLC/TS 50131-3 standard.
– ARMED (green) – steady light indicates that the partition assigned to this keypad has
been armed. The LEDs are blinking during exit delay countdown. Blinking indicates
that exit delay countdown is underway.
– TROUBLE (yellow) – blinking indicates occurrence of a technical problem. The signaling
refers to the troubles from the entire alarm system, not only from the keypad controlled
partition. Check the LCD keypad for the type of trouble. The trouble signaling is
temporarily disabled, when arming the keypad controlled partition. Disarming will
restore the trouble signaling. The LED is blinking until troubles are viewed in the LCD
keypad and the trouble memory is reset (option TROUBLE MEMORY UNTIL REVIEW
enabled) or until the trouble cause stops (option TROUBLE MEMORY UNTIL REVIEW
disabled) PROG.
When all the LEDs are alternately blinking (from top to bottom), there is no communication
between the keypad and the control panel. This situation may occur when the STARTER
program is running in the control panel or the cable connecting the partition keypad to the
control panel is damaged.
It is possible to program the partition PROG to be armed or disarmed after entering two
codes. In this case, entering the first code causes the LEDs labeled [
ARMED]and
[TROUBLE] and to blink alternately, while the control panel waits for entering the second
code.
Like the LCD keypad, the partition keypad may generate audible signals. Considering the
lack of a display, this is how the control panel acknowledges acceptance of the called
function.
•One short beep – acceptance of the code entry (provided that the option ACCES CODE
SIGNALING (HARDWARE)is enabled).
•One long beep – refusal of arming.