Sauder Shoal Creek 409733 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-25
Français p 26-28
Español p 29-32
Lot # 502115 02/28/17
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
Desk
Shoal Creek Collection | Model 409733
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
The oriinal desktop.

Table of Contents Assembly Tools Required
2-3
4
5-24
25-28
29-32
33-34
35
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
409733 www.sauder.com/servicesPae 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
A2 RIGHT END (1)
B2 LEFT END (1)
C2 UPRIGHT (1)
D2 TOP (1)
D14 LARGE RIGHT DRAWER SIDE (1)
D15 LARGE LEFT DRAWER SIDE (1)
D30 RIGHT DRAWER SIDE (1)
D31 LEFT DRAWER SIDE (1)
D77 DRAWER BACK (1)
D78 LARGE DRAWER BACK (1)
D83 PENCIL RIGHT DRAWER SIDE (1)
D84 PENCIL LEFT DRAWER SIDE (1)
D121 PENCIL DRAWER BACK (1)
D716 DRAWER BOTTOM (2)
D726 PENCIL DRAWER BOTTOM (1)
E3 BOTTOM (1)
F2 MODESTY PANEL (1)
G RIGHT FRONT/LEFT REAR LEG (2)
H LEFT FRONT/RIGHT REAR LEG (2)
I PENCIL DRAWER FRONT (1)
M64 DRAWER BRACE (1)
N DRAWER FRONT (1)
S2 LARGE DRAWER FRONT (1)
W DRAWER BOX FRONT (1)
X END MOLDING (2)
Y3 HUTCH RIGHT END (1)
Z3 HUTCH LEFT END (1)
AA3 HUTCH UPRIGHT (1)
BB2 HUTCH SHELF (1)
CC HUTCH BACK (1)

Part Identification
409733www.sauder.com/services Pae 3
A2
B2
C2
D2
E3
F2
G
H
X
Y3
Z3
CC
G
H
X
W
N
D716
D31
D30
D77
S2
D716
D14
D78
D15
I
D121
D726
D83
D84 M64
BB2
AA3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
409733 www.sauder.com/servicesPae 4
ADJUSTABLE
FOOT - 1
34E
BLACK 1-1/8" PAN HEAD SCREW - 4
9S
BLACK 9/16" LARGE HEAD SCREW - 4
1S
15S SILVER 5/8" MACHINE SCREW - 6
BLACK 1-7/8" FLAT HEAD SCREW - 9
2S
GROMMET CAP - 1
1P CAM
COVER - 3
12P
3S GOLD 5/16" FLAT HEAD SCREW - 24
METAL
PIN - 2
1R
PULL - 3
7K
10A SLIDE
CAM - 6
BLACK 9/16" FLAT HEAD SCREW - 4
32S
CAM SCREW - 13
8F
KNOB - 1
24K GROMMET - 1
10P
HIDDEN CAM - 35
1F CAM DOWEL - 22 2F
30S BLACK 1-9/16" FLAT HEAD SCREW - 13
FILE GLIDE - 2
4B
40CA CABINET RIGHT - 3 40CB CABINET LEFT - 3 40CC DRAWER RIGHT - 3 40CD DRAWER LEFT - 3
BLACK 7/8" MACHINE SCREW - 1
37S

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push thirty-five HIDDEN CAMS (1F) into the ENDS (A2
and B2), UPRIGHT (C2), BOTTOM (E3), MODESTY
PANEL (F2), HUTCH SHELF (BB2), HUTCH BACK (CC),
and DRAWER BRACE (M64). Then, insert the metal
end of a CAM DOWEL (2F) into each HIDDEN CAM
except the DRAWER BRACE (M64) and the lon edes
of the ENDS (A2 and B2).
409733www.sauder.com/services Pae 5
(35 used)
(22 used)
Arrow
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tihten the HIDDEN CAMS in this step.
Do not insert CAM
DOWELS into the
lon edes of the
ENDS (A2 and B2).
CC
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
A2
B2
C2
E3
F2
BB2
M64
1F
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1739
to watch a video on how to assemble your unit.

Step 2
å Turn thirteen CAM SCREWS (8F) into the LEGS (G
and H) and PENCIL DRAWER FRONT (I).
409733 www.sauder.com/servicesPae 6
G
H
G
H
I
(13 used)
8F

å Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into
the ENDS (A2 and B2) until the shoulders of the SCREWS
rest on the surfaces of the ENDS.
å Slide the END MOLDINGS (X) onto the ENDS (A2
and B2). Line up the rooves in the MOLDINGS over the
heads of the SCREWS in the ENDS.
Step 3
409733www.sauder.com/services Pae 7
A2
B2
X
X
Shoulder
These edes
should be even.
These edes
should be even.
Apply pressure with your hands as
you uide the MOLDINGS over the
SCREWS and onto the ENDS.
Surface
without
HIDDEN CAMS Surface
without
HIDDEN CAMS
Ede with CAM
DOWELS
BLACK 9/16" FLAT HEAD SCREW
(4 used in this step)
32S
Some assembly
(and snacks) required.

Step 4
å Fasten the LEGS (G and H) to the ENDS (A2 and B2).
Tihten twelve HIDDEN CAMS.
409733 www.sauder.com/servicesPae 8
A2
B2
G
H
G
H
Surface
with
HIDDEN CAMS
Surface
with
HIDDEN CAMS
Anled ede
These surfaces
should be even.
These surfaces
should be even.
Anled ede
1
2
X
X

å Fasten the CABINET RIGHTS (40CA) and CABINET
LEFTS (40CB) to the ENDS (A2 and B2) and UPRIGHT (C2).
Use twelve GOLD 5/16" FLAT HEAD SCREWS (3S)
throuh holes #1 and #3.
Step 5
409733www.sauder.com/services Pae 9
1
2
3
3
2
1
A2
C2
4
4
1
2
34
1
2
34
3
2
1
4
B2
Roller end
Roller end
These holes
must be here.
Finished ede
Roller end
Surface
with
HIDDEN CAMS
Surface with
HIDDEN CAMS
G
H
Surface
without
HIDDEN
CAMS
1
2
34
GOLD 5/16" FLAT HEAD SCREW
(12 used in this step)
3S

Step 6
å Fasten the HUTCH LEFT END (Z3) to the HUTCH
BACK (CC). Tihten two HIDDEN CAMS.
409733 www.sauder.com/servicesPae 10
Z3
CC
Surface with HIDDEN CAMS
Anled ede
Finished ede
Start Tighten
Arrow
Minimum
190 derees
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Arrow
Maximum
210 derees

å Lay your HUTCH assembly onto the HUTCH BACK (CC).
å Insert one METAL PIN (1R) into the hole in the short ede of
the HUTCH SHELF (BB2).
å Fasten the HUTCH SHELF (BB2) to the HUTCH LEFT
END (Z3). Tihten the HIDDEN CAM.
å NOTE: Be sure the METAL PIN in the HUTCH SHELF inserts
into the hole in the HUTCH LEFT END.
Step 7
409733www.sauder.com/services Pae 11
Z3
CC
1R
Surface
with
HIDDEN CAMS
Anled ede
Finished ede
Arrow
Minimum
190 derees
Maximum
210 derees
BB2

Step 8
409733 www.sauder.com/servicesPae 12
å Insert one METAL PIN (1R) into the hole in the short ede of
the HUTCH SHELF (BB2).
å Fasten the HUTCH SHELF (BB2) to the HUTCH RIGHT
END (Y3). Tihten the HIDDEN CAM.
å NOTE: Be sure the METAL PIN in the HUTCH SHELF
inserts into the hole in the HUTCH RIGHT END.
å Turn the HUTCH assembly over onto its front anled ede
and fasten the HUTCH RIGHT END (Y3) to the HUTCH
BACK (CC). Tihten two HIDDEN CAMS.
Arrow
Minimum
190 derees
Maximum
210 derees
Y3
CC
Anled ede
BB2
1R

å Fasten the TOP (D2) to the HUTCH UPRIGHT (AA3). Use two
BLACK 1-7/8" FLAT HEAD SCREWS (2S).
å Fasten the TOP (D2) to the HUTCH BACK (CC). Use four
BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Step 9
409733www.sauder.com/services Pae 13
D2
Be sure the head of
this SCREW is flat
aainst the TOP.
Surface with more holes
BLACK 1-7/8" FLAT HEAD SCREW
(6 used in this step)
2S
Finished ede
D2
Finished ede
CC
2S
Finished ede
AA3
Now miht be a
ood time to refresh
your drink.

Step 10
å Fasten the LEFT END (B2) to the TOP (D2). Tihten two
HIDDEN CAMS.
409733 www.sauder.com/servicesPae 14
B2
D2
Surface
with
HIDDEN CAMS
Surface with more holes
Roller end
Arrow
Minimum
190 derees
Maximum
210 derees
For support, place packin
foam and maazines here.

å Fasten the MODESTY PANEL (F2) to the LEFT END (B2).
Tihten three HIDDEN CAMS.
Step 11
409733www.sauder.com/services Pae 15
B2
F2
Surface
with
HIDDEN CAMS
Arrow
Minimum
190 derees
Maximum
210 derees
Notch

Step 12
å Fasten the RIGHT END (A2) to the TOP (D2). Tihten two
HIDDEN CAMS.
å Fasten the MODESTY PANEL (F2) to the RIGHT END (A2).
Tihten three HIDDEN CAMS.
å Fasten the BOTTOM (E3) to the RIGHT END (A2). Tihten
two HIDDEN CAMS.
A2
E3
D2
Surface
with
HIDDEN CAMS
Arrow
Minimum
190 derees
Maximum
210 derees
Surface
with
HIDDEN CAMS
F2
409733 www.sauder.com/servicesPae 16
NOTICE: The orientation
view has been chaned
from the last step with
the RIGHT END (A2) here.
The lare hole
must be here.

Step 13
409733www.sauder.com/services Pae 17
å Fasten the UPRIGHT (C2) to the TOP (D2) and BOTTOM (E3).
Tihten four HIDDEN CAMS.
å Fasten the MODESTY PANEL (F2) to the UPRIGHT (C2). Use
three BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Finished ede
Surface
with
HIDDEN CAMS
Arrow
Minimum
190 derees
Maximum
210 derees
C2
E3
D2
F2
BLACK 1-7/8" FLAT HEAD SCREW
(3 used for the MODESTY PANEL)
2S

StepStep 14
409733 www.sauder.com/servicesPae 18
E3
å Fasten the ADJUSTABLE FOOT (34E) to the BOTTOM (E3).
Use four BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Adjustments to the ADJUSTABLE FOOT (34E) will
be made in Step 20 after your unit is standin upriht.
34E
BLACK 9/16" LARGE HEAD SCREW
(4 used in this step)
1S
Don't worry. It isn't
Rome. This can be built
in a day.

StepStep 15
å Insert the PENCIL DRAWER SIDES (D83 and D84)
at an angle into the slot at each end of the PENCIL
DRAWER FRONT (I).
å Slide the PENCIL DRAWER BOTTOM (D726) into the
grooves in the PENCIL DRAWER SIDES (D83 and D84)
and PENCIL DRAWER FRONT (I).
å Fasten the DRAWER BRACE (M64) to the PENCIL
DRAWER FRONT (I). Tighten one HIDDEN CAM. å Fasten the PENCIL DRAWER BACK (D121) to the
PENCIL DRAWER SIDES (D83 and D84) and DRAWER
BRACE (M64). Use five BLACK 1-9/16" FLAT
HEAD SCREWS (30S).
The tabs should insert freely
into the slots. Gently tilt the
DRAWER SIDES side to side
until the tabs slip into the slots.
Unfinished surface
12
34
Be sure the DRAWER
BOTTOM inserts into the
DRAWER FRONT roove.
Groove
Arrow
Maximum
210 derees
Minimum
190 derees
II
I
VIEW THE T-LOCK BOX VIDEO
D84
D83
D84
D726
D83
D83
D84
D121
409733www.sauder.com/services Pae 19
M64
M64
With the palm of your hand,
tap the DRAWER BOTTOM
down into the roove.
Surface with
HIDDEN CAM
Start each screw a few turns before
completely tihtenin any of them.
BLACK 1-9/16" FLAT HEAD SCREW
(5 used in this step)
30S

StepStep 16
409733 www.sauder.com/servicesPae 20
VIEW THE T-LOCK BOX VIDEO
å Fasten the DRAWER BACK (D77) to the DRAWER SIDES (D30 and D31). Use four BLACK 1-9/16" FLAT
HEAD SCREWS (30S).
å NOTE: Be sure the DRAWER BOTTOM (D716) inserts into the roove of the DRAWER BACK (D77).
å Repeat this step for the remainin drawer.
12
3
å Insert the DRAWER SIDES (D30 and D31) at an anle into
the slot at each end of the DRAWER BOX FRONT (W).
å Slide the DRAWER BOTTOM (D716) into the rooves in the
DRAWER SIDES (D30 and D31) and DRAWER BOX FRONT (W).
The tabs should insert freely
into the slots. Gently tilt the
DRAWER SIDES side to side
until the tabs slip into the slots.
Groove Be sure the DRAWER
BOTTOM inserts into the
DRAWER FRONT roove.
D30
D31
D716
D716
D30
D31
D77
D31
W W
Unfinished
surface
D30
Start each screw a few turns before
completely tihtenin any of them.
BLACK 1-9/16" FLAT HEAD SCREW
(8 used in this step)
30S
With the palm of
your hand, tap the
DRAWER BOTTOM
down into the roove.