Sauder Pacific View 427044 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-523-3987.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey! Lot # 542627 03/26/20
Purchased: __________________
English pg 1-28
Français pg 29-32
Español pg 33-36
Bookcase
Pacific View Collection | Model 427044
The stories of your life.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
5-28
29-32
33-36
37-38
39
427044 www.sauder.com/servicePage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A END (2)
B TOP (1)
C BOTTOM (1)
D LEFT FRONT/RIGHT REAR LEG (2)
E RIGHT FRONT/LEFT REAR LEG (2)
F TOP FRONT MOLDING (1)
G SIDE MOLDING (4)
H BOTTOM FRONT MOLDING (1)
J UPRIGHT MOLDING (1)
K TOP REAR MOLDING (1)
L UPRIGHT (1)
M RIGHT SHELF (1)
N LEFT SHELF (1)
O ADJUSTABLE SHELF (4)
P BACK (1)
427044www.sauder.com/service Page 3
A
B
C
D
E
F
G
H
J
K
L
M
N
O
P
A
D
E
G
G
O
O
O
G

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
427044 www.sauder.com/servicePage 4
ADJUSTABLE FOOT - 1
34E HIDDEN CAM - 41 1F CAM DOWEL - 14 2F CAM SCREW - 27 8F
WOOD DOWEL - 14
15F NAIL - 61 1N
FURNITURE TIPPING
RESTRAINT KIT - 1
97
APPLIQUE CARD - 4
93P METAL PIN - 16 1R RUBBER SLEEVE - 16 2R
BLACK 9/16" LARGE HEAD SCREW - 8
1S SILVER 1-1/8" FLAT HEAD SCREW - 8 10S
BLACK 1-15/16" FLAT HEAD SCREW - 6
113S
MOLDING
CONNECTOR - 4
16F

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM DOWEL
Cam Screw
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2. 3.
1
2
Insert the CAM SCREW into the HIDDEN CAM.
Tighten the HIDDEN CAM.
HOW TO USE A HIDDEN CAM & CAM SCREW
Turn the CAM SCREW until
the shoulder is against the
surface of the part.
1.
2. Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the edge
of the board.
Hole
Arrow
Metal end
Hidden Cam
Cam Dowel
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
3.
427044www.sauder.com/service Page 5

Step 1
å Assemble your unit on a carpeted floor or on the
empty carton to avoid scratching your unit or the floor.
å Push five HIDDEN CAMS (1F) into the UPRIGHT (L).
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
427044 www.sauder.com/servicePage 6
1
1F
Arrow
L
1F
Arrow
Just think. The sooner
you do this, the sooner
you do something else.

å Turn three CAM SCREWS (8F) into the UPRIGHT MOLDING (J).
å Fasten the UPRIGHT MOLDING (J) to the UPRIGHT (L). Tighten
three HIDDEN CAMS.
Step 2
427044www.sauder.com/service Page 7
J
L
J
1
8F

å Slide the BOTTOM FRONT MOLDING* (H) onto the
notched edge of the BOTTOM (C).
å *U.S. Patent No. 5,499,886
Step 3
427044 www.sauder.com/servicePage 8
Slide the MOLDING (H)
onto the notched edge.
These surfaces
should be even.
The groove
is closer to
this edge.
Notched edge
Surface with
more holes
C
H

å Fasten the BOTTOM (C) to the UPRIGHT (L). Use two
BLACK 1-15/16" FLAT HEAD SCREWS (113S).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
å Fasten the ADJUSTABLE FOOT (34E) to the BOTTOM (C).
Use four BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 4
427044www.sauder.com/service Page 9
L
C
Surface without
HIDDEN CAMS
H
J
34E
BLACK 1-15/16" FLAT HEAD SCREW
(2 used for the UPRIGHT)
113S
BLACK 9/16" LARGE HEAD SCREW
(4 used for the ADJUSTABLE FOOT)
1S
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

å Push eight HIDDEN CAMS (1F) into the SHELVES (M and N).
Then, insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM.
Step 5
427044 www.sauder.com/servicePage 10
M
N
1
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
2F
Metal end
Arrow
1F
2F
Metal end