Sauder 412321 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
English.................... Page 1-22
Français...............Pages 23-25
Espanol.............Páginas 26-29
Lot #: 353030 05 / 08 / 13
Date Purchased: ____________________
412321
Technology Pier
August Hill Collection

ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-22
Français..............................23-25
Espanol...............................26-29
Safety .......................................30
Warranty...................................31
Page 2 www.sauder.com/services 412321

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C TOP 1
D BOTTOM 1
E SHELF 2
F SMALL BACK 1
G LARGE BACK 1
HRIGHT FRONT/LEFT
REAR LEG 2
ILEFT FRONT/RIGHT
REAR LEG 2
J DRAWER FRONT 2
D10 RIGHT DRAWER SIDE 2
D11 LEFT DRAWER SIDE 2
D962 DRAWER BOTTOM 2
D62 DRAWER BACK 2
O VERTICAL MOLDING 2
P BOTTOM MOLDING 1
Q LONG TOP MOLDING 1
R LOWER END MOLDING 2
S UPPER END MOLDING 2
T SHELF MOLDING 2
U SHORT TOP MOLDING 2
J
D11
D11
D62
J
D10
D11
D62
GA
B
C
D
E
E
F
H
H
I
IO
OP
R
R
S
S
T
T
U
U
Q
Page 3
www.sauder.com/services412321
D962
D962

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
NAIL - 29
OO
GROMMET CAP - 1
BB
BLACK 1-7/8" FLAT HEAD SCREW - 2
II
CORD CLIP - 2
FF
CAM COVER - 6
EE
GOLD 5/16" FLAT HEAD SCREW - 16
MM
TWIST-LOCK® FASTENER - 13
X
ANGLE BRACKET - 6
AA
BLACK 9/16" LARGE HEAD SCREW - 12
LL
BLACK 9/16" FLAT HEAD SCREW - 14
KK
PULL - 2
HH
WASHER - 2
GG
SILVER 1/4" MACHINE SCREW - 2
NN
SLIDE CAM - 4
DD
CAM SCREW -16
Z
HIDDEN CAM - 16
Y
CC GROMMET - 1
(EXTENSION SET SHOWN SEPARATED)
VEXTENSION RAIL - 4 WEXTENSION SLIDE - 4
Page 4 www.sauder.com/services 412321
BLACK 1-9/16" FLAT HEAD SCREW - 8
JJ

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (X) into the large holes in the BOTTOM (D), SHELVES (E), and
SMALL BACK (F).
Do not tighten the TWIST-LOCK® FASTENERS in this step.
X
X
D
E
E
F
Page 5
www.sauder.com/services412321

Turn sixteen CAM SCREWS (Z) into the TOP (C) and LEGS (H and I).
Push sixteen HIDDEN CAMS (Y) into the ENDS (A and B) and LEGS (H and I).
2
2
S
t
e
p
Do not tighten the HIDDEN CAMS in this step.
(16 used)
(16 used)
Arrow
Arrow
H
H
I
I
A
B
Z
Z
Z
Y
Y
Y
Arrow
C
Arrow
Page 6 www.sauder.com/services 412321

3
3
S
t
e
p
H
I
A
B
Fasten one of each LEGS (H and I) to the ENDS (A and B). Tighten six HIDDEN CAMS.
The HIDDEN CAMS should be here.
Page 7
www.sauder.com/services412321
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Arrow
Maximum
210 degrees
Minimum
190 degrees
Arrow

Carefully flip the ENDS over.
Turn fourteen BLACK 9/16" FLAT HEAD SCREWS (KK) into the ENDS (A and B) until the shoulder of the SCREWS rest on the
surface of the END.
1. Slide the LOWER END MOLDING (R) onto the ENDS (A and B). Line up the groove in the MOLDINGS over the head of the
SCREWS in the MOLDINGS.
2. Slide the VERTICAL MOLDING (O) onto the ENDS (A and B) until is against the LOWER END MOLDINGS (R). Line up the
groove in the MOLDINGS over the head of the SCREWS in the MOLDINGS.
4
4
S
t
e
p
BLACK 9/16" FLAT HEAD SCREW
(14 used in this step)
KK
Shoulder
Shoulder
Apply pressure with your hands as
you guide the MOLDINGS over
the SCREWS and onto the ENDS.
Apply pressure with your hands as
you guide the MOLDINGS over
the SCREWS and onto the ENDS.
These edges
should be even.
These edges
should be even.
1st
1st
1st
2nd
2nd A
B
R
R
R
O
O
O
Page 8 www.sauder.com/services 412321

Slide the UPPER END MOLDINGS (S) onto the ENDS (A and B) until it is against the LEGS. Line up the groove in the
MOLDINGS over the head of the SCREWS in the MOLDINGS.
5
5
S
t
e
p
Apply pressure with your hands as
you guide the MOLDINGS over
the SCREWS and onto the ENDS.
S
S
A
B
Page 9
www.sauder.com/services412321

Carefully flip the ENDS over.
Fasten the remaining LEGS (H and I) to the ENDS (A and B). Tighten six HIDDEN CAMS.
6
6
S
t
e
p
H
I
A
B
Page 10 www.sauder.com/services 412321
The HIDDEN CAMS should be here.