Sauder Anywhere Dakota Pass 418231 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-31
Français p 32-35
Español p 36-39
Lot # 367574 03/17/15
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
Anywhere Console
Dakota Pass Collection | 418231
Designed for
distractions.

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
WARNING
!
Skip the power trip.
This time.
3
4-5
6-31
32-35
36-39
40-42
43
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
50 lbs.
50 lbs.
17-5/8"
17-5/8"
37-5/8"
37-5/8"
Use of a TV that is too heavy or lare is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too lare for the available space miht be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weiht of your TV. Compare it to the diaram below – before you begin assembly!
• This Sauder unit is desined for use with televisions weihin less than 50 pounds. Never use with a TV that weihs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diaram.
• Never place the front ede of the TV past the front ede of the TV support shelf (or stop moldin – if equipped)
• Never allow the sides of the TV to extend past the side edes of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warnin label as instructed in the last assembly step. The label provides important safety related information.
418231 www.sauder.com/servicesPae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E ROLL-OUT RIGHT END (1)
F ROLL-OUT LEFT END (1)
G ROLL-OUT BOTTOM (1)
H ROLL-OUT BACK (1)
I BACK (1)
J FLIP-UP DOOR (1)
K DRAWER FRONT (1)
L RIGHT LEG (1)
M LEFT LEG (1)
N REAR LEG (2)
O TOP MOLDING (1)
P BOTTOM MOLDING (1)
Q SHELF MOLDING (1)
R BRACE (1)
S DRAWER FRONT MOLDING (4)
D12 RIGHT DRAWER SIDE (1)
D13 LEFT DRAWER SIDE (1)
D189 DRAWER BACK (1)
D955 DRAWER BOTTOM (1)
M67 DRAWER BRACE (1)
418231www.sauder.com/services Pae 3
A
B
C
DE
F
G
H
I
J
K
L
M
N
O
P
Q
R
D12
D13
D189
D955
S
S
N
M67

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
WARNING
Never use this furniture with a TV that is
too large or too heavy. Severe injury or
death can occur.The TV and furniture
will be unstable and may tip.
-The TV must less than 50 lbs.
-The base of the TV must be able to sit
completely on this shelf.
Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not
try to remove. Surface will be damaged.
08/05 2 6 9 2 2 0 269220
WARNING LABEL - 1
1L
(Refer to step 25 for proper
location and application)
VEXTENSION SLIDE - 2 UEXTENSION RAIL - 2
(EXTENSION SET SHOWN SEPARATED)
35GA CABINET RIGHT - 1 35GB CABINET LEFT - 1
35GC DRAWER RIGHT - 1 35GD DRAWER LEFT - 1 ADJUSTABLE FOOT - 1
34E
SAFETY
STRAP - 1
60M SAFETY DRYWALL
ANCHOR - 1
61M
DRAWER BRACKET SET - 1
55G
418231 www.sauder.com/servicesPae 4
WASHER - 1
13M
FELT DISC CARD - 1
1M
CAM
COVER - 4
13P
7F TWIST-LOCK®
FASTENER - 10
MOLDING
CONNECTOR - 2
17F
10A SLIDE CAM - 2
CAM SCREW - 10
8F
CORD
CLIP - 3
9P
WOOD DOWEL - 2
15F
28K KNOB- 6
NAIL - 36
1N
HIDDEN CAM - 10
1F
Locate this nylon SAFETY
STRAP (60M) to be used
later in assembly. Do not
accidentally throw away.
SMALL WOOD
DOWEL - 2
26F

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
418231www.sauder.com/services Pae 5
GOLD 1" MACHINE SCREW - 6
50S
BLACK 9/16" LARGE HEAD SCREW - 5
1S
BLACK 7/8" FLAT HEAD SCREW - 6
31S
BLACK 1-7/8" FLAT HEAD SCREW - 8
2S
BLACK 2-1/4" FLAT HEAD SCREW - 6
26S
3S GOLD 5/16" FLAT HEAD SCREW - 16 SILVER 5/8" FLAT HEAD SCREW - 4 23S
SILVER 1" LARGE HEAD SCREW - 12
102S
30S BLACK 1-9/16" FLAT HEAD SCREW - 5

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å To bein assembly, push a SAUDER TWIST-LOCK®
FASTENER (7F) into the lare holes in the ENDS (A and B),
BOTTOM (D), and BRACE (R).
418231 www.sauder.com/servicesPae 6
Do not tihten the TWIST-LOCK® FASTENERS in this step.
7F
7F
A
B
D
R

Step
å Turn ten CAM SCREWS (8F) into the DRAWER FRONT (K),
FRONT LEGS (L and M), and TOP MOLDING (O).
å Push ten HIDDEN CAMS (1F) into the ENDS (A and B),
TOP (C), and DRAWER BRACE (M67).
Step 2
418231www.sauder.com/services Pae 7
8F
Arrow
Arrow
1F
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
Arrow
1F
(10 used)
(10 used)
A
B
C
KO
L
M
M67

Step 3
418231 www.sauder.com/servicesPae 8
å Separate the EXTENSION SLIDES (V) from the
EXTENSION RAILS (U) as shown in the enlared diaram
below. Be prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (U) to the ENDS (A and B).
Use four GOLD 5/16” FLAT HEAD SCREWS (3S).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the
hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other hole
that lines up with the hole in the END. Turn a SCREW into
this hole.
Open end
Open end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Push the black lever in and pull the SLIDE from the RAIL.
Remember:
Rihty tihty.
Lefty loosey.
A
B
V U
U
U
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Ede with
HIDDEN CAMS
Ede with
HIDDEN CAMS

Step 4
418231www.sauder.com/services Pae 9
å Fasten a CABINET RIGHT (35GA) to the RIGHT END (A)
and a CABINET LEFT (35GB) to the LEFT END (B). Use
four GOLD 5/16" FLAT HEAD SCREWS (3S) throuh
holes #1 and #3.
1
2
3
1
2
3
Roller end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Roller end
A
B
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Ede with
HIDDEN CAMS
Ede with
HIDDEN CAMS

å Fasten the REAR LEGS (N) to the ENDS (A and B). Use six
BLACK 2-1/4" FLAT HEAD SCREWS (26S).
Step 5
418231 www.sauder.com/servicesPae 10
BLACK 2-1/4" FLAT HEAD SCREW
(6 used in this step)
26S
A
B
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Ede with
HIDDEN CAMS
Ede with
HIDDEN CAMS
Anled ede
N
N
These surfaces
should be even.
These surfaces
should be even.