Sauder 420477 User manual

Share your journey!
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-18
Français pg 19-21
Español pg 22-24
Here's one for
the books.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
2-3
4
5-18
19-21
22-24
25-26
27
Page 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C2 TOP (1)
D SHELF (1)
E BOTTOM (1)
F ADJUSTABLE SHELF (3)
G BACK (1)
I SHORT END MOLDING (2)
J FEET (2)
M12 TOP MOLDING (1)
M13 BOTTOM MOLDING (1)
M38 SHELF MOLDING (1)
M59 VALANCE (1)
M61 SKIRT (1)
M71 LONG END MOLDING (2)

Part Identification Now you know
our ABCs.
A
B
C2
D
E
F
F
G
M71 I
M12
M38
M13
M59
M61
J
Page 3
F
M71
J
I

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 1-1/8" PAN HEAD SCREW - 3
9S
TIE PLATE - 4
3G ANGLE BRACKET - 14 27G
BLACK 9/16" LARGE HEAD SCREW - 36
1S BLACK 1-7/8" FLAT HEAD SCREW - 2 2S
10F TWIST-LOCK®
FASTENER - 12
FOOT SCREW - 2
23F
METAL PIN - 12
1R
CAM SCREW - 3
14F
NAIL - 41
1N
BLACK 1-7/8" PAN HEAD SCREW - 3
16S
HIDDEN CAM - 3
1F
Page 4
RUBBER SLEEVE - 12
2R
FURNITURE TIPPING RESTRAINT KIT - 1
97

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the fl oor.
å To begin assembly, push a TWIST-LOCK®
FASTENER (10F) into the large holes in the ENDS (A and B).
å Repeat this step for the SHELF (D) and BOTTOM (E).
Page 5
Do not tighten the TWIST-LOCK® FASTENERS in this step.
(12 used)
10F
A
B

å Turn three CAM SCREWS (14F) into the SHELF MOLDING (M38).
å NOTE: Be sure to use the exact holes shown.
å Push three HIDDEN CAMS (1F) into the SHELF (D).
Step 2
Page 6
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
D
M38
14F
Arrow
1F

Step 3
Page 7
å Fasten fourteen ANGLE BRACKETS (27G) to the
ENDS (A and B). Use fourteen BLACK 9/16" LARGE
HEAD SCREWS (1S).
å NOTE: Be sure the edges of the ANGLE BRACKETS
are even with the edges of the ENDS.
BLACK 9/16" LARGE HEAD SCREW
(14 used for the ANGLE BRACKETS)
1S
(14 used)
Remember:
Righty tighty.
Lefty loosey.
27G
27G
B
A
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS

Step 4
Page 8
Dowel end
A
C2
D
E
Long finished edge
These holes
must be here.
å Fasten the RIGHT END (A) to the TOP (C2). Tighten
two TWIST-LOCK® FASTENERS.
å Fasten the SHELF (D) and BOTTOM (E) to the RIGHT
END (A). Tighten four TWIST-LOCK® FASTENERS.
Surface with holes
Edge with
HIDDEN CAMS
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Edge with
ANGLE
BRACKETS
How to use the TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.

å Fasten the LEFT END (B) to the TOP (C2), SHELF (D), and
BOTTOM (E). Tighten six TWIST-LOCK® FASTENERS.
Step 5
Page 9
B
C2
D
E
Edge with
ANGLE
BRACKETS

å Fasten the TOP MOLDING (M12) to the TOP (C2). Use
three BLACK 1-7/8" PAN HEAD SCREWS (16S).
å NOTE: Do not overtighten the SCREWS into the TOP.
å Fasten the SHELF MOLDING (M38) to the SHELF (D).
Tighten three HIDDEN CAMS.
BLACK 1-7/8" PAN HEAD SCREW
(3 used in this step)
16S
Step 6
Page 10
These surfaces should be even.
A
B
M12
M38
D
C2
Curved edge
1
2