Sauder Avenue Eight 416514 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-28
Français p 29-32
Español p 33-36
Lot # 398140 11/09/16
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
Lateral File
Avenue Eiht Collection | Model 416514
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Get all organized
and stu.

Table of Contents Assembly Tools Required
2-3
4-5
6-28
29-32
33-36
37-38
39
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
416514 www.sauder.com/servicesPae 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
A OUTER RIGHT END (1)
B OUTER LEFT END (1)
C3 INNER RIGHT END (1)
D3 INNER LEFT END (1)
D33 RIGHT DRAWER SIDE (2)
D32 LEFT DRAWER SIDE (2)
D61 DRAWER BACK (2)
D729 DRAWER BOTTOM (2)
E2 TOP (1)
F2 BOTTOM (1)
G BACK (1)
H BRACE (1)
I DRAWER FRONT (2)
M35 VERTICAL MOLDING (2)
M63 DRAWER BRACE (2)
N SKIRT (1)
O FRONT MOLDING (1)
P BOTTOM MOLDING (1)
R RIGHT MOLDING (1)
S LEFT MOLDING (1)
T PLINTH (4)
U HALF DISK (4)

Part Identification Now you know
our ABCs.
416514www.sauder.com/services Pae 3
A
B
C3
D3
E2
F2
G
H
N
O
P
R
S
T
T
T
T
I
D729
D32
D33
D61
U
U
M63
M35
M35
U
U

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
416514 www.sauder.com/servicesPae 4
(EXTENSION SET SHOWN SEPARATED)
EXTENSION RAIL - 4
WEXTENSION SLIDE - 4 X
ANGLE BRACKET - 10
27G
7F TWIST-LOCK®FASTENER - 12 MOLDING
CONNECTOR - 2
17F
20G DRAWER STOP - 2 29G SAFETY STOP - 2
NAIL - 36
1N
FILE BRACKET - 4
12B
KNOB - 4
42K
HIDDEN CAM - 2
1F CAM DOWEL - 2 2F
FILE DRAWER FRONT
BRACKET - 4
10G
FILE GLIDE - 4
5B
INTERLOCK TRACK - 1
22G
FILE ROD - 4
9B
FILE BAR - 4
1B
METAL PIN - 4
1R
METAL BRACKET - 6
4G

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
416514www.sauder.com/services Pae 5
SILVER 1/2" MACHINE SCREW - 4
38S
BLACK 9/16" LARGE HEAD SCREW - 44
1S
SILVER 1-1/8" FLAT HEAD SCREW - 12
10S
BLACK 1-1/4" FLAT HEAD SCREW - 4
7S
BROWN 7/16" LARGE HEAD SCREW - 4
6S
12S BROWN 1" FLAT HEAD SCREW - 6
3S GOLD 5/16" FLAT HEAD SCREW - 16
30S BLACK 1-9/16" FLAT HEAD SCREW - 10
BLACK 1-15/16" FLAT HEAD SCREW - 4
113S

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the
empty carton to avoid scratchin your unit or the floor.
å To bein assembly, push a SAUDER TWIST-LOCK®
FASTENER (7F) into the lare holes in the
OUTER ENDS (A and B).
å Repeat this step for the INNER ENDS (C3 and D3),
and BOTTOM (F2).
416514 www.sauder.com/servicesPae 6
A
B
7F
(12 used)
Do not tihten the TWIST-LOCK® FASTENERS in this step.

å Fasten four HALF DISKS (U) to four PLINTHS (T). Use four SILVER
1-1/8" FLAT HEAD SCREWS (10S).
å Fasten ten ANGLE BRACKETS (27G) to the OUTER ENDS (A and B).
Use ten BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the edes of the ANGLE BRACKETS are even with
the edes of the ENDS.
å Fasten the PLINTHS (T) and VERTICAL MOLDINGS (M35) to the
ENDS (A and B). Use ten BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 2
416514www.sauder.com/services Pae 7
The larer
hole should
be facin up.
T
T
T
T
T
T
U
U
U
U
A
B
Surface with
TWIST-LOCK
®
FASTENERS
Surface with
TWIST-LOCK
®
FASTENERS
Use the holes below the roove in
the VERTICAL MOLDING (M35).
Use the holes
below the roove
in the VERTICAL
MOLDING (M35).
27G
27G
The VERTICAL
MOLDINGS should
be centered over
the HALF DISKS.
The VERTICAL MOLDINGS should
be centered over the HALF DISKS.
(10 used)
SILVER 1-1/8" FLAT HEAD SCREW
(4 used for the HALF DISKS)
10S
BLACK 9/16" LARGE HEAD SCREW
(20 used for the ANGLE BRACKETS)
1S
M35
M35
Use the lower two
holes in the PLINTH.

Step 3
å The next three steps involve an important safety feature
desined to prevent more than one drawer from openin
at the same time.
å Insert the two SAFETY STOPS (29G) into the holes
shown in the INNER RIGHT END (C3).
416514 www.sauder.com/servicesPae 8
C3
This pin must insert into the location
holes in the INNER RIGHT END (C3).
29G
29G
29G

å Diaram 1. Measure 1-1/2" from one end of the INTERLOCK TRACK (22G). Position the
INTERLOCK TRACK as shown.
å SAFETY STOP / TRACK ATTACHMENT:
å Diaram 2. Tilt the first ede of the INTERLOCK TRACK (22G) into the SAFETY STOP (29G).
å Diaram 3. Rotate the INTERLOCK TRACK and apply force to snap the second ede into
the SAFETY STOP.
å Diaram 4. Repeat the SAFETY STOP/ TRACK ATTACHMENT for the next SAFETY
STOPS while holdin the previously completed SAFETY STOP in its location hole. Visually
check that all INTERLOCK TRACK edes have been snapped into the SAFETY STOPS as
shown in diaram 3.
å Diaram 5. Remove the INTERLOCK TRACK assembly from Diaram 4 and flip it over
before insertin the INTERLOCK TRACK (22G) with SAFETY STOPS (29G) into the roove
in the INSIDE RIGHT END (C3).
Step 4
416514www.sauder.com/services Pae 9
C3
C3
Cut out this rectanle
to use as a "spacer"
1-1/2"
4.
5.
1.
1-1/2"
29G
2. 3.
29G
22G
22G
22G
22G
STOP
Be sure the
interlock track
snaps into each
safety stop.
F
L
I
P
O
V
E
R

Step 5
å Separate the EXTENSION SLIDES (X) from the EXTENSION RAILS (W) as
shown in the upper diaram below. Be prepared, the parts are reasy.
å Fasten four EXTENSION RAILS (W) to the INNER ENDS (C3 and D3). Use
eiht GOLD 5/16" FLAT HEAD SCREWS (3S).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in
the enlared diaram. Then, slide the inner cartride of the EXTENSION
RAIL in to find the other hole that lines up with the hole in the END. Turn a
SCREW into this hole.
416514 www.sauder.com/servicesPae 10
Push the black lever in and pull the SLIDE from the RAIL.
After fastenin the EXTENSION RAIL to the INNER
END (C3), the SAFETY STOP should touch the top
ede of the RAILS. If the ap is larer than 1/16"
the drawers could lock up and not open. If this
happens, open two drawers at the same time to
override the interlock system. Remove the drawers
to re-adjust the INTERLOCK TRACK assembly.
W
W
W
W
W
X
C3
D3
Open end
Open end
Open end
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
3S