Sauder Entertainment Credenza 403891 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-22
Français p 23-25
Lot # 346467 08/24/12
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
Entertainment Credenza
Harvest Mill Collection | Model 403891
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Smart stand
for the idiot box.

Table of Contents Assembly Tools Required
3
4-5
6-22
23-25
26
27
Part Identification
Hardware Identification
Assembly Steps
Français
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Use of a TV that is too heavy or lare is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too lare for the available space miht be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weiht of your TV. Compare it to the diaram below – before you begin assembly!
• This Sauder unit is desined for use with televisions weihin less than 95 pounds. Never use with a TV that weihs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diaram.
• Never place the front ede of the TV past the front ede of the TV support shelf (or stop moldin – if equipped)
• Never allow the sides of the TV to extend past the side edes of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warnin label as instructed in the last assembly step. The label provides important safety related information.
WARNING
!
95 lbs.
95 lbs.
17-1/4"
17-1/4"
47-1/2"
47-1/2"
403891 www.sauder.com/servicesPae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
A END (2)
B RIGHT UPRIGHT (1)
C LEFT UPRIGHT (1)
D TOP (1)
E BOTTOM (1)
F BACK (1)
G BRACE (1)
H DOOR (2)
I ADJUSTABLE SHELF (2)
J SMALL ADJUSTABLE SHELF (2)
K SIDE SKIRT (2)
M FRONT MOLDING (1)
N MOLDING (2)
O END MOLDING (2)
P SIDE MOLDING (2)
Q RIGHT BACK (1)
R LEFT BACK (1)
S RIGHT SKIRT (1)
T LEFT SKIRT (1)
403891www.sauder.com/services Pae 3
A
B
C
D
E
F
G
H
I
J
K
M
N
O
P
Q
R
S
T
P
A
I
J
N
O
KH

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
403891 www.sauder.com/servicesPae 4
(Refer to the last step for proper
location and application)
WARNING LABEL - 1
GG
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur.The TV and furniture will be
unstable and may tip.
-The TV must less than 95 lbs.
-The base of the TV must be able to sit
completely on this shelf.
-Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not try
to remove. Surface will be damaged.
02/ 02 269227
FELT DISC CARD - 1
BB
METAL BRACKET - 9
X
HIDDEN CONNECTOR - 2
U
RUBBER SLEEVE - 16
FF
METAL PIN - 24
EE
YHINGE - 4
HIDDEN CAM - 4
V2 CAM DOWEL - 4
W2
AA
HINGE SPACER - 4
KNOB - 2
CC BACKPLATE - 2 DD

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
403891www.sauder.com/services Pae 5
BLACK 1-1/8" MACHINE SCREW - 2
LL BLACK 9/16" LARGE HEAD SCREW - 18 MM
BLACK 1-1/4" FLAT HEAD SCREW - 9
JJ
CONNECTOR SCREW - 2
PP
BLACK 1-7/8" FLAT HEAD SCREW - 12
HH BROWN 1-1/2" FLAT HEAD SCREW - 4 II
NAIL - 15
OO
SILVER 1-1/4" PAN HEAD SCREW - 2
KK
SILVER 5/8" FLAT HEAD SCREW - 8
QQ

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
403891 www.sauder.com/servicesPae 6
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Insert a CONNECTOR SCREW (PP) into each
HIDDEN CONNECTOR (U). U
PP
å Use your hammer to tap two HIDDEN
CONNECTORS (U) with SCREWS into
the SIDE SKIRTS (K).
Step 2
U
U
K
K
Do not tap a HIDDEN
CONNECTOR here.
Do not tap a HIDDEN
CONNECTOR here.

å Push four HIDDEN CAMS (V2) into the UPRIGHTS (B and C).
Then, insert a CAM DOWEL (W2) into each HIDDEN CAM.
Step 3
403891www.sauder.com/services Pae 7
Arrow
V2
W2
Do not tihten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
B
C
(4 used)

403891 www.sauder.com/servicesPae 8
Step 4
å Fasten the SIDE MOLDINGS (P) to the ENDS (A). Use four
BLACK 1-7/8" FLAT HEAD SCREWS (HH).
A
P
P
A
Surface
with holes
Surface
with holes
Notched ede
Notched ede
Unfinished ede
These edes
must be even.
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
HH
Unfinished ede

å Fasten the FRONT MOLDING (M) to the TOP (D). Use five
BLACK 1-1/4" FLAT HEAD SCREWS (JJ).
Step 5
403891www.sauder.com/services Pae 9
D
M
Finished
surface
Rounded ede
BLACK 1-1/4" FLAT HEAD SCREW
(5 used in this step)
JJ
Surface with holes

Step 6
403891 www.sauder.com/servicesPae 10
å Fasten the SIDE MOLDINGS (P) to the TOP (D). Use four
BLACK 1-1/4" FLAT HEAD SCREWS (JJ).
Notched ede
Rounded ede
Notched ede
A
D
P
P
A
Surface
with holes
Surface
without holes
BLACK 1-1/4" FLAT HEAD SCREW
(4 used in this step)
JJ
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution
Surface with holes