Sauder Summit Station 427287 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-523-3987.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey! Lot # 543218 03/10/20
Purchased: __________________
English pg 1-52
Français pg 53-58
Español pg 59-64
Executive Desk
Summit Station Collection | Model 427287
Business or pleasure.
Works both ways.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
2-3
4-5
6-52
53-58
59-64
65-66
67
427287 www.sauder.com/servicePage 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
D14 LARGE RIGHT DRAWER SIDE (2)
D15 LARGE LEFT DRAWER SIDE (2)
D20 SMALL RIGHT DRAWER SIDE (2)
D21 SMALL LEFT DRAWER SIDE (2)
D24 RIGHT DRAWER SIDE (2)
D25 LEFT DRAWER SIDE (2)
D74 SMALL DRAWER BACK (2)
D78 LARGE DRAWER BACK (2)
D109 DRAWER BACK (2)
D716 DRAWER BOTTOM (6)
E MODESTY PANEL (1)
F BOTTOM (2)
G BACK (2)
H RIGHT FRONT/LEFT REAR LEG (4)
J FRONT MOLDING (2)
K LEFT FRONT/RIGHT REAR LEG (4)
L DRAWER FRONT (2)
M SMALL DRAWER FRONT (2)
N KEYBOARD DRAWER FRONT (1)
O KEYBOARD DRAWER BACK (1)
P KEYBOARD DRAWER BOTTOM (1)
Q KEYBOARD DRAWER SIDE (2)
R LARGE DRAWER FRONT (2)
S SIDE MOLDING (4)
T MODESTY PANEL MOLDING (1)
U BACK MOLDING (2)
V TOP (1)

Part Identification Now you know
our ABCs.
427287www.sauder.com/service Page 3
A
B
C
D
E
F
G
H
J
K
L
M
N
O
P
Q
R
S
T
V
D20
D716
U
FJ
G
H
K
H
K
H
K
Q
S
S
S
U
D21
D74
D24
D716
D25
D109
D14
D716
D15
D78

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
427287 www.sauder.com/servicePage 4
40AW CABINET RIGHT - 1 40AX CABINET LEFT - 1 40AY DRAWER RIGHT - 1 40AZ DRAWER LEFT - 1
40CA CABINET RIGHT - 4 40CB CABINET LEFT - 4 40CC DRAWER RIGHT - 4 40CD DRAWER LEFT - 4
(EXTENSION SET SHOWN SEPARATED)
EXTENSION RAIL - 4
35MA EXTENSION SLIDE - 4 35MC 10A SLIDE CAM - 12 FILE GLIDE - 4
4B
HIDDEN
CAM - 24
1F CAM
SCREW - 24
8F WOOD
DOWEL - 16
15F SMALL WOOD
DOWEL - 4
26F
7F TWIST-LOCK®
FASTENER - 24
EXTENSION
BRACKET - 4
43G PULL - 7
35K
HINGE - 2
12H 29M BUMPER
CARD - 1
GROMMET
CAP - 1
1P GROMMET - 1 10P

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
427287www.sauder.com/service Page 5
BLACK 9/16" LARGE HEAD SCREW - 8
1S 3S GOLD 5/16" FLAT HEAD SCREW - 52
BROWN 1-1/2" FLAT HEAD SCREW - 6
14S 18S BROWN 1" FLAT HEAD SCREW - 4
SILVER 5/8" FLAT HEAD SCREW - 4
23S 30S BLACK 1-9/16" FLAT HEAD SCREW - 24
BLACK 9/16" FLAT HEAD SCREW - 14
32S BLACK 7/8" MACHINE SCREW - 14 37S
SILVER 9/16" LARGE HEAD SCREW - 2
54S BLACK 1-15/16" FLAT HEAD SCREW - 4
113S

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to avoid
scratching your unit or the floor.
å Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into the LEFT END (B) and
LEFT UPRIGHT (D) until the shoulders of the SCREWS rest on the surfaces of
the END and UPRIGHT.
å NOTE: Do not overtighten the SCREWS.
å Slide two SIDE MOLDINGS (S) onto the LEFT END (B) and LEFT UPRIGHT (D).
Line up the grooves in the MOLDINGS over the heads of the SCREWS in the
END and UPRIGHT.
å NOTE: The MOLDINGS should be centered on the END and UPRIGHT.
å NOTE: If the MOLDING comes up o of the SCREWS,
remove it and slide it on again.
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code. 0
427287 www.sauder.com/servicePage 6
B
D
Shoulder
Apply pressure with your hands as you
guide the MOLDINGS over the SCREWS
and onto the END and UPRIGHT.
BLACK 9/16" FLAT HEAD SCREW
(4 used in this step)
32S
Surface with
fewer holes
Surface with
fewer holes
S
S

Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
Cam Screw
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2. 3.
1
2
Insert the CAM SCREW into the HIDDEN CAM.
Tighten the HIDDEN CAM.
HOW TO USE A HIDDEN CAM & CAM SCREW
Turn the CAM SCREW until
the shoulder is against the
surface of the part.
1.
427287www.sauder.com/service Page 7

å Carefully turn the LEFT END (B) and LEFT UPRIGHT (D) over.
å Push six SAUDER TWIST-LOCK® FASTENERS (7F) into the
large holes in the LEFT END (B) and LEFT UPRIGHT (D).
å Push twelve HIDDEN CAMS (1F) into the LEFT END (B) and
LEFT UPRIGHT (D).
Step 2
427287 www.sauder.com/servicePage 8
B
D
(12 used)
1F
Arrow
1F
Arrow
12
7F
Do not tighten the TWIST-LOCK® FASTENERS in this step.
1
2

å Turn twelve CAM SCREWS (8F) into the LEGS (H and K)
as shown.
å Insert four WOOD DOWELS (15F) into the LEGS (H and K).
Step 3
427287www.sauder.com/service Page 9
K
H
K
H
1
8F
15F
(12 used)

Step 4
427287 www.sauder.com/servicePage 10
å Fasten one set of LEGS (H and K) to the LEFT END (B).
Tighten six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the LEGS insert
into the LEFT END.
K
H
B
These surfaces
should be even.
Edge with
TWIST-LOCK®
FASTENERS
1
Angled edge
Angled edge
Surface with
HIDDEN CAMS