Sauder 423493 User manual

Lot # 531001 06/24/19
Purchased: __________________
English pg 1-12
Français pg 13-14
Español pg 15-16
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Share your journey!
3-Shelf Bookcase
Model 423493
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
The stories of your life.

Table of Contents Assembly Tools Required
2
3
4-12
13-14
15-16
17-18
19
Hardware Identification
Part Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Page 2 www.sauder.com 423493
Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
HIDDEN CAM - 30
1
CAM COVER - 12
54 TACK GLIDE - 4
NAIL - 30
10
CAM SCREW - 30
2METAL PIN - 8 3
FURNITURE TIPPING RESTRAINT KIT - 1
99
Skip the power trip.
This time.

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E ADJUSTABLE SHELF (2)
F ADJUSTABLE SHELF MOLDING (2)
G VALANCE (1)
H BASE (1)
J END MOLDING (2)
K BACK (1)
Now you know
our ABCs.
Page 3www.sauder.com423493
B
A
D
E
C
H
F
K
J
G
J
E
F

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push thirty HIDDEN CAMS (1) into the ENDS (A and B),
TOP (C), BOTTOM (D), and ADJUSTABLE SHELVES (E).
1
Arrow
1
Arrow
Arrow
1
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
(30 used)
Page 4 www.sauder.com 423493
B
A
D
E
C
E

StepStep 2
å Turn thirty CAM SCREWS (2) into the ENDS (A and B), TOP (C),
ADJUSTABLE SHELF MOLDINGS (F), VALANCE (G), BASE (H),
and END MOLDINGS (J).
Page 5www.sauder.com423493
2
H
F
J
G
JF
(30 used)
B
A
C

StepStep 3
å Fasten the ENDS (A and B) to the BOTTOM (D). Tighten
four HIDDEN CAMS.
Page 6 www.sauder.com 423493
1
2
B
A
D
Surface with
HIDDEN CAMS
Surface without HIDDEN CAMS
Surface without
HIDDEN CAMS
Edge with HIDDEN CAMS
Edge with HIDDEN CAMS

Step
å Fasten the TOP (C) to the ENDS (A and B). Tighten four
HIDDEN CAMS.
Step 4
Page 7www.sauder.com423493
C
B
A
Edge with HIDDEN CAMS
Surface without HIDDEN CAMS
Just think. The sooner
you do this, the sooner
you do something else.

Step
å Unfold the BACK (K) and lay it over your unit.
å Make equal margins along all four edges of the BACK (K). Push
on opposite corners of your unit if needed to make it "square".
å Fasten the BACK (K) to your unit using the NAILS (10).
Step 5
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Unfinished
surface
Page 8 www.sauder.com 423493
K
NAIL
(30 used in this step)
10

Page 9www.sauder.com423493
Step 6
å Carefully turn your unit over onto its back.
å Fasten the VALANCE (G) to the TOP (C) and ENDS (A and B).
Tighten five HIDDEN CAMS.
å Fasten the END MOLDINGS (J) to the ENDS (A and B). Tighten
six HIDDEN CAMS.
B
A
C
J
G
J
These surfaces
should be even.

Step 7
å Fasten the BASE (H) to the ENDS (A and B) and BOTTOM (D).
Tighten five HIDDEN CAMS.
å With your hammer, gently tap the TACK GLIDES (4) into the
bottom edges of the ENDS (A and B) and BASE (H) as shown.
Page 10 www.sauder.com 423493
B
A
D
H
4
If you're doing this to
help a friend, don't
leave without a bite.