Sauder Edge Water Series User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-28
Français pg 29-32
Español pg 33-36
Lot # 392445 06/27/16
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Executive Desk
Edge Water Collection | Model 418795
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Get executive
with this decision.

åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E2 TOP (1)
F MODESTY PANEL (1)
G BACK (2)
H BRACE (2)
I FRONT LEG (4)
J REAR LEG (4)
K KEYBOARD FRONT (1)
L KEYBOARD BACK (1)
M KEYBOARD SIDE (2)
N KEYBOARD SHELF (1)
O LARGE DRAWER FRONT (2)
S SMALL DRAWER FRONT (2)
V MODESTY PANEL MOLDING (1)
W MOLDING (4)
X TOP MOLDING (2)
Y FOOT (8)
D241 LARGE DRAWER BOX FRONT (4)
D242 SMALL DRAWER BOX FRONT (4)
D253 LARGE DRAWER SIDE (4)
D270 SMALL DRAWER SIDE (4)
D717 DRAWER BOTTOM (4)
Table of Contents Assembly Tools Required
2-3
4-5
6-28
29-32
33-36
37-38
39
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Part Identification
418795 www.sauder.com/servicesPage 2

Part Identification
A
B
C
D
E2
F
G
H
I
J
K
L
MN
O
S
W
X
J
J
J
S
O
M
W
W
W
X
I
I
I
Y
Y
Y
Y
Y
Y
Y
Y
V
418795www.sauder.com/services Page 3
G
H
D242
D270 D717
D717
D717
D270
D270
D270
D242
D253
D253
D241
D241
D241
D241
D253
D253
D242
D242
D717

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
FILE GLIDE - 4
4BFF EXTENSION SLIDE - 4 EE EXTENSION RAIL - 4
(EXTENSION SET SHOWN SEPARATED)
RIGHT DRAWER SLIDE - 1
CC LEFT DRAWER SLIDE - 1 DD
LEFT CABINET RAIL - 1
BB
RIGHT CABINET RAIL - 1
AA
7F TWIST-LOCK®
FASTENER - 14
HIDDEN CAM - 40
1F
CAM SCREW - 40
8F ANGLE BRACKET - 4
5G
GROMMET - 1
10P
GROMMET
CAP - 1
1P
KEYBOARD
HINGE - 2
12H
RAIL BRACKET - 4
18G
418795 www.sauder.com/servicesPage 4
29M BUMPER
CARD - 1
40CA CABINET RIGHT - 2 40CB CABINET LEFT - 2 40CC DRAWER RIGHT - 2 40CD DRAWER LEFT - 2
124K KNOB - 6

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 1-7/8" FLAT HEAD SCREW - 6
2S
BLACK 1-1/4" FLAT HEAD SCREW - 40
7S
SILVER 1-1/8" FLAT HEAD SCREW - 4
10S
BLACK 1-1-8" PAN HEAD SCREW - 7
9S
BLACK 1-1/8" MACHINE SCREW - 4
21S18S BROWN 1" FLAT HEAD SCREW - 4
BLACK 7/8" LARGE HEAD SCREW - 12
17S
BLACK 7/8" MACHINE SCREW - 2
37S
SILVER 5/8" FLAT HEAD SCREW - 4
23S
BLACK 9/16" LARGE HEAD SCREW - 16
1S
SILVER 9/16" LARGE HEAD SCREW - 2
54S
GOLD 5/16" FLAT HEAD SCREW - 36
3S
418795www.sauder.com/services Page 5
16S BLACK 1-7/8" PAN HEAD SCREW - 8

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (7F) into the large holes in the UPRIGHTS (C
and D) and MODESTY PANEL (F).
å NOTE: Do not insert TWIST-LOCK® FASTENERS into the
ENDS (A and B) and BACKS (G).
C
D
7F
F
(6 used)
Do not tighten the TWIST-LOCK® FASTENERS in this step.
418795 www.sauder.com/servicesPage 6
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1546
to watch a video on how to assemble your unit.

å Push forty HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHTS (C and D), BACKS (G), and BRACES (H).
Step 2
Arrow
The arrow in the HIDDEN CAM
must point toward the hole in
the edge of the board.
Hole
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
Arrow
1F
AB
C
D
G
H
G
H
418795www.sauder.com/services Page 7
(40 used)

Step 3
å Turn forty CAM SCREWS (8F) into the ENDS (A and B),
UPRIGHTS (C and D), and LEGS (I and J).
8F
8F
8F
A
B
CD
I
J
J
J
J
I
I
I
418795 www.sauder.com/servicesPage 8
These holes will not be used
on the FRONT LEGS (I).
(40 used)

å Fasten a FRONT LEG (I) and a REAR LEG (J) to the RIGHT
END (A) and RIGHT UPRIGHT (C). Tighten twelve
HIDDEN CAMS.
å Fasten a FOOT (Y) to each LEG (I and J). Use four BLACK
1-7/8" PAN HEAD SCREWS (16S).
Step 4
A
C
J
J
I
I
Y
Y
Y
Y
12
418795www.sauder.com/services Page 9
These CAM SCREWS
should be here.
These CAM SCREWS
should be here.
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
These surfaces should be even.
These surfaces should be even.
Surface with
CAM SCREWS
BLACK 1-7/8" PAN HEAD SCREW
(4 used in this step)
16S
Some assembly
(and snacks) required.

Step 5
å Fasten a FRONT LEG (I) and a REAR LEG (J) to the LEFT
END (B) and LEFT UPRIGHT (D). Tighten twelve
HIDDEN CAMS.
å Fasten a FOOT (Y) to each LEG (I and J). Use four BLACK
1-7/8" PAN HEAD SCREWS (16S).
D
B
J
J
I
I
Y
Y
Y
Y
12
418795 www.sauder.com/servicesPage 10
These CAM SCREWS
should be here.
These CAM SCREWS
should be here.
These surfaces should be even.
These surfaces should be even.
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
CAM SCREWS
BLACK 1-7/8" PAN HEAD SCREW
(4 used in this step)
16S