Sauder Camarin 414466 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
English.................... Page 1-22
Français...............Pages 23-25
Espanol.............Páginas 26-28
Lot #: 353302 05 / 16 / 13
Date Purchased: ____________________
414466
Corner TV Stand
Camarin Collection

ADULT ASSEMBLY REQUIRED
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury
or death. ATV that is too large for the available space might be accidentally pushed or bumped off the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 50 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
WARNING
ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-22
Français..............................23-25
Espanol...............................26-28
Safety .................................29-30
Warranty...................................31
15-1/2"
35"
50 lbs.
Page 2 www.sauder.com/services 414466
Short Screwdriver

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C RIGHT UPRIGHT 1
D LEFT UPRIGHT 1
D24 DRAWER RIGHT SIDE 2
D25 DRAWER LEFT SIDE 2
D70 DRAWER BACK 2
D719 DRAWER BOTTOM 2
E TOP 1
F BOTTOM 1
G SHELF 1
H BACK 1
I BACK SUPPORT 1
J ADJUSTABLE SHELF 1
K FRONT SKIRT 1
L SIDE SKIRT 2
M DRAWER FRONT 2
O BRACE 1
RLEFT FRONT/RIGHT
REAR FOOT 2
SRIGHT FRONT/LEFT
REAR FOOT 2
D24
D24
D25
D25
D70
D70
D719
D719
A
B
C
D
E
F
G
H
I
J
K
L
L
M
M
O
S
S
Page 3
www.sauder.com/services414466
R
R

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
BLACK 9/16" LARGE HEAD SCREW - 28
1S
CAM COVER - 6
12P
GOLD 5/16" FLAT HEAD SCREW - 16
3S
SLIDE CAM - 4
10A
SHELF SNAP - 2
6R
METAL PIN - 6
1R RUBBER SLEEVE - 2 2R
BLACK 1-7/8" FLAT HEAD SCREW - 10
2S
METAL BRACKET - 2
4G NAIL - 32 1N
KNOB - 2
73K
GOLD 1" MACHINE SCREW - 2
50S
HIDDEN CAM - 14
1F CAM DOWEL - 14 2F
SILVER 5/8" FLAT HEAD SCREW - 4
23S
SILVER 7/8" PAN HEAD SCREW - 4
22S
CORNER
BRACKET - 4
31G
FOOT BASE - 1
24E FOOT - 1 25E
Page 4 www.sauder.com/services 414466
WARNING
Never use this furniture with a TV that is
too large or too heavy. Severe injury or
death can occur.The TV and furniture
will be unstable and may tip.
-The TV must less than 50 lbs.
-The base of the TV must be able to sit
completely on this shelf.
Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not
try to remove. Surface will be damaged.
08/05 2 6 9 2 2 0 269220
WARNING LABEL - 1
1L
(Refer to the step 17 for proper location and application)
35GA CABINET RIGHT - 2 35GB CABINET LEFT - 2 35GC DRAWER RIGHT - 2 35GD DRAWER LEFT - 2
BLACK 1-9/16" FLAT HEAD SCREW - 8
30S

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push fourteen HIDDEN CAMS (1F) into the ENDS (A and B), UPRIGHTS (C and D), SHELF (G), and BACK SUPPORT (I). Then,
insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM.
Page 5
www.sauder.com/services414466
Do not tighten the HIDDEN CAMS in this step.
Arrow
(14 used)
(14 used)
Arrow
1F
1F
2F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
A
BC
D
G
I

Page 6 www.sauder.com/services 414466
Fasten the LEFT END (B) to the TOP (E). Tighten two HIDDEN CAMS.
2
2
S
t
e
p
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Arrow
Arrow
Maximum
210 degrees
Minimum
190 degrees
Rounded edge
Rounded edge
Surface with
HIDDEN
CAMS
Surface
with holes
B
E

Page 7
www.sauder.com/services414466
3
3
S
t
e
p
Surface without
HIDDEN CAMS
Fasten the BACK SUPPORT (I) to the TOP (E). Tighten two HIDDEN CAMS.
Maximum
210 degrees
Minimum
190 degrees
Arrow
I
E

Page 8 www.sauder.com/services 414466
4
4
S
t
e
p
Fasten the SHELF (G) to the LEFT END (B). Tighten two HIDDEN CAMS.
Fasten the SHELF (G) to the BACK SUPPORT (I). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Maximum
210 degrees
Minimum
190 degrees
Arrow
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
2S B
G
I
Surface with
HIDDEN CAMS
Finished edge

Fasten the RIGHT END (A) to the TOP (E) and SHELF (G). Tighten four HIDDEN CAMS.
Page 9
www.sauder.com/services414466
5
5
S
t
e
p
Maximum
210 degrees
Minimum
190 degrees
Arrow
E
G
A
Surface without
HIDDEN CAMS
Rounded edge

Page 10 www.sauder.com/services 414466
Fasten the CABINET RIGHT (35GA) and CABINET LEFT (35GB) to the UPRIGHTS (C and D). Use eight GOLD 5/16" FLAT HEAD
SCREWS (3S) through holes #1 and #3.
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
3S
1
2
3
3
32
21
1
Finished edge
Finished edge
1
2
3
Roller end
Roller end
Roller end
Roller end
C
D
Edge with CAM DOWELS
6
6
S
t
e
p