Sauder Via 401446 User manual

sauder.com
Desk Return
Via Collection | Model 401446
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-26
Français pg 27-31
Español pg 32-36
Lot # 524134 12/10/18
Purchased: __________________
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-523-3987.
Customer Service is available Monday-Friday - 8:30 a.m. to 5 p.m. EST (except holidays)
Sauder.com
Share your journey!
For left and right
brains, alike.

Table of Contents Assembly Tools Required
3
4
5-26
27-31
32-36
37-38
39
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
401446 www.sauder.com/servicePage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C LARGE END (1)
D2 TOP (1)
E BACK (1)
Now you know
our ABCs.
401446www.sauder.com/service Page 3
A
B
C
D2
E

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
401446 www.sauder.com/servicePage 4
BLACK 7/8" LARGE HEAD SCREW - 16
17S
BLACK 9/16" LARGE HEAD SCREW - 2
1S
CONNECTOR PLATE - 2
14G
PROPEL NUT - 3
14M
TOUCH-UP PEN - 1
10M
7F TWIST-LOCK®
FASTENER - 19
GROMMET CAP - 1
1P GROMMET - 1 10P
61P TWIST-LOCK®
FASTENER COVER - 19 63P HALF GROMMET - 1 64P HALF GROMMET CAP - 1
16E LEVELER - 3
32G LEVELER
BRACKET - 3
65P CORD
MANAGER - 2
HOLE PLUG - 4
26P

Step 1
å You have the choice of assembling this unit six ways:
å 1. If attaching the 401446 Desk Return to the right or left side of the 401447 Executive Desk and 401448 Credenza (for a
U-Shape configuration) continue with Step 2.
å 2. If attaching the 401446 Desk Return to the right or left side of the 401447 Executive Desk (for an L-Shape configuration)
continue with Step 7.
å 3. If attaching the 401446 Desk Return to the right or left side of the 401448 Credenza (for an L-Shape configuration)
continue with Step 15.
401446www.sauder.com/service Page 5
401446
401447
401448
401446
401447
401448
401446
401448
401446
401448
401446
401447
401446
401447
U-Shape Assembly
L-Shape Assembly
(Continue with Step 2 now)
(Continue with Step 7 now) (Continue with Step 15 now)
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code. 0

Step 2
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (7F) into the large holes in the ENDS (A and B)
and BACK (E).
å NOTE: The LARGE END (C) is not used in the
U-Shape assembly.
401446 www.sauder.com/servicePage 6
Do not tighten the TWIST-LOCK® FASTENERS in this step.
7F
A
B
E
Do not tap TWIST-LOCK® FASTENERS into the
other surfaces of the ENDS (A and B) at this time.
U-Shape Assembly
7F
7F
2

å Push two LEVELER BRACKETS (32G) over the holes in the bottom edges of
the ENDS (A and B).
å Use a hammer to drive a PROPEL NUT (14M) into the holes in the LEVELER
BRACKETS (32G) and ENDS (A and B). Now, turn a LEVELER (16E) into each
PROPEL NUT.
å NOTE: To raise a corner of the unit, turn the LEVELER counter-clockwise. To
lower a corner, turn the LEVELER clockwise.
Step 3
401446www.sauder.com/service Page 7
A
B
32G
16E
14M
U-Shape Assembly

Step 4
å Insert the dowel end of four TWIST-LOCK® FASTENERS (7F) into the 401447
Left End and 401448 Right End as shown in the enlarged diagram.
å NOTE: If you already pushed TWIST-LOCK® FASTENERS into the holes in the
ENDS (A and B), pull the FASTENERS back out of the holes. Pull at the front
and back edges, slowly working the FASTENERS out of the holes.
å Push the ENDS (A and B) onto the TWIST-LOCK® FASTENERS in the 401448
Right End and 401447 Left End. Now, tighten eight TWIST-LOCK® FASTENERS.
401446 www.sauder.com/servicePage 8
U-Shape Assembly
401447 Desk Top
401448
Credenza Top
401447
Left End
401448
Right End
A
B
Finished edge
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
7F
2

å NOTE: Before beginning this step, separate the BLACK 7/8"
LARGE HEAD SCREWS (17S) and BLACK 9/16" LARGE
HEAD SCREWS (1S). Do not confuse these SCREWS.
å Fasten the BACK (E) to the ENDS (A and B). Tighten eight
TWIST-LOCK® FASTENERS.
å Fasten two CORD MANAGERS (65P) to the BACK (E). Use
two BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 5
401446www.sauder.com/service Page 9
U-Shape Assembly
401447
401448
A
E
65P
Surface with
TWIST-LOCK®
FASTENERS
Edge with TWIST-LOCK® FASTENERS
B
BLACK 9/16" LARGE HEAD SCREW
(2 used for the CORD MANAGERS)
1S
2
Remember:
Righty tighty.
Lefty loosey.

Step 6
å Fasten two CONNECTOR PLATES (14G) to the 401447
Desk Top and 401448 Credenza Top. Use eight
BLACK 7/8" LARGE HEAD SCREWS (17S).
å Fasten the TOP (D2) to the BACK (E). Tighten three
TWIST-LOCK® FASTENERS.
å Fasten the TOP (D2) to the 401447 Desk Top and
401448 Credenza Top. Use eight BLACK 7/8" LARGE
HEAD SCREWS (17S) through the CONNECTOR PLATES
and into the TOP.
å Go to the last step now.
401446 www.sauder.com/servicePage 10
U-Shape Assembly
401447 Desk Top
401448
Credenza Top
BLACK 7/8" LARGE HEAD SCREW
(16 used for the CONNECTOR PLATES)
17S
14G
14G
E
D2
Long finished edge
2