Sauder Briarbrook 430076 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-23
Français pg 24-27
Español pg 28-31
Lot # 573700 11/01/21
Purchased: __________________
Library Hutch
Briarbrook Collection | Model 430076
Don't sweat the
small stu anymore.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5
6-23
24-27
28-31
32-34
35
Electric drill with 1/8" or 3/8" bit
(ONLY in indicated step)
Pencil
Page 2 www.sauder.com/service 430076

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A TOP (1)
B ADJUSTABLE SHELF (1)
C BOTTOM (1)
D LEFT END (1)
E UPRIGHT (1)
F RIGHT END (1)
G FIXED SHELF (2)
H FRAME (2)
J BACK (1)
K MOLDING (2)
A
B
C
D
E
F
G
H
J
K
K
G
H
Page 3www.sauder.com/service430076

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
CAM SCREW - 14
1HIDDEN CAM - 14 2WOOD DOWEL - 7 3NUT - 4
4
WRENCH - 1
6
L-WRENCH - 1
5PAD CARD - 1 7APPLIQUE CARD - 1
8
FURNITURE TIPPING
RESTRAINT KIT - 1
96
1-9/16" HEX HEAD SCREW - 2
91/2" HEX HEAD SCREW - 20
10
3/8" HEX HEAD SCREW - 4
11 1/2" PAN HEAD SCREW - 6 12
Page 4 www.sauder.com/service 430076

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 5www.sauder.com/service430076

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
å Assemble your unit on a carpeted floor or on the empty carton
to avoid scratching your unit or the floor.
å Push fourteen HIDDEN CAMS (2) into the ENDS (D and F),
UPRIGHT (E), and FIXED SHELVES (G).
å Turn six CAM SCREWS (1) into the ENDS (D and F)
and UPRIGHT (E).
å Flip over the UPRIGHT (E).
å Turn two CAM SCREWS (1) into the UPRIGHT (E).
1
D
E
F
G
G
E
2
Arrow
Arrow
2
2
Arrow
F
L
I
P
O
V
E
R
1
1
(8 used)
Page 6 www.sauder.com/service 430076
Some assembly
(and snacks) required.

å Insert four WOOD DOWELS (3) into the ENDS (D and F) and UPRIGHT (E).
å Fasten the ENDS (D and F) and UPRIGHT (E) to the FIXED SHELVES (G) as
shown. Tighten eight HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the ENDS and UPRIGHT insert into
the FIXED SHELVES.
Step 2
D
E
F
G
G
3
3
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Page 7www.sauder.com/service430076
1

å Turn six CAM SCREWS (1) into the BOTTOM (C).
Step 3 1
C
1
1
Page 8 www.sauder.com/service 430076

å Insert three WOOD DOWELS (3) into the BOTTOM (C).
å Fasten the BOTTOM (C) to the ENDS (D and F) and
UPRIGHT (E). Tighten six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the BOTTOM
insert into the ENDS and UPRIGHT.
Step 4
C
D
E
F
3
3
3
1
Edge without holes
Page 9www.sauder.com/service430076

å Fasten the MOLDINGS (K) to the TOP (A). Tighten two
1-9/16" HEX HEAD SCREWS (9) using the L-WRENCH (5).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 5
Page 10 www.sauder.com/service 430076
This hole must be here.
A
K
K
This hole must be here.
51-9/16" HEX HEAD SCREW
(2 used in this step)
9
Meet Part (A). This component has
been engineered to be lighter, stronger,
faster… well ok. Not technically faster.
But definitely makes for a sturdier
Library Hutch that’s easier to assemble
and friendlier to the environment.

Step 6
å NOTE: Use the hole locations of your choice for the ADJUSTABLE SHELF (B).
å Fasten the FRAMES (H) to the ADJUSTABLE SHELF (B), ENDS (D and F), and
MOLDINGS (K) as shown. Tighten sixteen 1/2" HEX HEAD SCREWS (10) using
the L-WRENCH (5).
å NOTE: You should start each SCREW a few turns before completely tightening
any of them.
Page 11www.sauder.com/service430076
B
D
FH
K
K
H
5
1/2" HEX HEAD SCREW
(16 used in this step)
10
This hole must be here.
Part (B). Another
sturdier, easier,
friendlier component!
These holes must be here.

å Fasten the FRAMES (H) to the TOP (A). Tighten four 1/2"
HEX HEAD SCREWS (10) using the L-WRENCH (5).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
å Peel the PADS from the PAD CARD (7) and apply them to
the bottom of the FRAMES (H).
Step 7
A
H
H
51/2" HEX HEAD SCREW
(4 used in this step)
10
7
Page 12 www.sauder.com/service 430076
Now might be a
good time to refresh
your drink.

å You have the option to have the Library Hutch on the
430070 or 430075.
å If you want the Library Hutch on the 430075 go to Step 9.
å If you want the Library Hutch on the 430070 go to Step 14.
Step 8
Library Hutch on 430075
Steps 9 - 13
Library Hutch on 430070
Steps 14 - 18
Page 13www.sauder.com/service430076
430070
430075

StepStep 9
å Carefully stand your unit upright and place on top of the 430075.
å Fasten the FRAMES (H) to the 430075. Tighten four 3/8" HEX HEAD
SCREWS (11) using the L-WRENCH (5) and tighten the NUTS (4) onto
the 3/8" HEX HEAD SCREWS using the WRENCH (6) as shown in the
enlarged diagram.
å NOTE: You should start each SCREW a few turns before completely
tightening any of them.
Page 14 www.sauder.com/service 430076
H
H
H
5
3/8" HEX HEAD SCREW
(4 used in this step)
11
4
6
430075

Step
å Fasten the BACK (J) to the BOTTOM (C) and 430075 top. Use six 1/2" PAN HEAD SCREWS (12).
å NOTE: You should start each SCREW a few turns before completely tightening any of them.
å Open the FURNITURE TIPPING RESTRAINT KIT (96), and fasten the SAFETY STRAP to the MOLDING (K) as shown.
Use the provided SHORT SCREW.
Step 10
C
J
1/2" PAN HEAD SCREW
(6 used in this step)
12
96
K
Page 15www.sauder.com/service430076
430075
Use the SHORT SCREW
from the RESTRAINT KIT.
SAFETY STRAP

Step
å Place your unit in its final location.
å NOTE: The following instructions show your unit being fastened to a wall stud. If you are not fastening your unit to a
wall stud, go to the next step now.
å 1st- Locate the center of a stud in your wall near your unit and mark it with a pencil just below the top surface of your
unit so the SAFETY STRAP will not be visible.
å 2nd- Drill a 1/8" hole on the mark and into the stud in your wall.
å 3rd-
Fasten the unit to the wall. Use the LONG SCREW through the other end of the SAFETY STRAP and into the 1/8" hole.
Step 11
Page 16 www.sauder.com/service 430076
1st
Electric drill with 1/8" bit
2nd
96
3rd
Mark and drill
a 1/8" hole into
the wall stud.
430075

å 1st- With your pencil, strike a mark through the center of the hole in the SAFETY STRAP just below
the top surface of your unit so the SAFETY STRAP will not be visible.
å 2nd- Drill a 3/8" hole on the mark.
å 3rd- While you squeeze the wings together, gently tap the WALL ANCHOR from the FURNITURE
TIPPING RESTRAINT KIT (96) into the hole until it is even with the surface of the wall.
å 4th- Turn the LONG SCREW through the hole in the SAFETY STRAP and into the WALL ANCHOR.
å NOTE: You will need to turn the LONG SCREW multiple turns to completely tighten and secure
your unit to the wall.
Step 12
4th
96
1st
Electric drill with 3/8" bit
2nd
Mark and drill
a 3/8" hole
into the wall.
3rd
Squeeze the wings
together and tap the
wall anchor into the
3/8" hole in the wall.
Page 17www.sauder.com/service430076
430075

å Peel APPLIQUES from the APPLIQUE CARD (8) and stick them onto each visible HIDDEN CAM.
å NOTE: Please read the back pages of the instruction booklet for important safety information.
å This completes assembly. Clean with a damp cloth. Wipe dry.
Step 13
8
And to celebrate, why not share your success story at sauder.com or
15 lbs.
15 lbs. 15 lbs.
35 lbs.
35 lbs.
Page 18 www.sauder.com/service 430076
430075
Hey! It's starting to look
like something!

å Carefully stand your unit upright and place on top of the 430070.
å Fasten the FRAMES (H) to the 430070. Tighten four 3/8" HEX HEAD
SCREWS (11) using the L-WRENCH (5) and tighten the NUTS (4) onto
the 3/8" HEX HEAD SCREWS using the WRENCH (6).
å NOTE: You should start each SCREW a few turns before completely
tightening any of them.
Step 14
H
H
H
5
3/8" HEX HEAD SCREW
(4 used in this step)
11
4
6
430070
Page 19www.sauder.com/service430076

å Fasten the BACK (J) to the BOTTOM (C) and the 430070.
Use six 1/2" PAN HEAD SCREWS (12).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
å Open the FURNITURE TIPPING RESTRAINT KIT (96),
and fasten the SAFETY STRAP to the MOLDING (K) as
shown. Use the provided SHORT SCREW.
Step 15
Page 20 www.sauder.com/service 430076
C
J
1/2" PAN HEAD SCREW
(6 used in this step)
12
K
96
430070
Use the SHORT SCREW
from the RESTRAINT KIT.
SAFETY STRAP