Sauder Shoal Creek Series User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-20
Français pg 21-23
Español pg 24-26
Lot # 355798 10/03/13
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Queen Platform Bed
Shoal Creek Collection | 414866
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
You are getting sleepy.
Very sleepy.

åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A HEAD END (1)
B FOOT END (1)
C REAR UPPER LONG END (1)
D REAR LOWER LONG END (1)
E UPPER LONG END (1)
F LOWER LONG END (1)
G LARGE CENTER UPRIGHT (2)
H HEAD UPRIGHT (2)
I FOOT UPRIGHT (2)
J DRAWER UPRIGHT (2)
K RIGHT LONG TOP (1)
L LEFT LONG TOP (1)
M SHORT TOP (1)
N BACK (1)
O LARGE CORNER (2)
P SMALL CORNER (2)
Q RIGHT DRAWER FRONT (1)
R LEFT DRAWER FRONT (1)
S SLAT (5)
T DRAWER BRACE (2)
D50 RIGHT DRAWER SIDE (2)
D51 LEFT DRAWER SIDE (2)
D80 DRAWER BACK (2)
D986 DRAWER BOTTOM (2)
Table of Contents Assembly Tools Required
2-3
4
5-20
21-23
24-26
27
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Part Identification
414866 www.sauder.com/servicesPage 2
Short Screwdriver

Part Identification
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
O
P
S
S
S
S
D50
D986
D51
D80
D50
D986
D51
D80
G
H
I
J
T
414866www.sauder.com/services Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
PROPEL NUT - 8
14M
BLACK 9/16" LARGE HEAD SCREW - 8
1S
SILVER 1-1/8" FLAT HEAD SCREW - 8
10S
15S SILVER 5/8" MACHINE SCREW - 4
BLACK 1-7/8" FLAT HEAD SCREW - 34
2S
3S GOLD 5/16" FLAT HEAD SCREW - 16
30S BLACK 1-9/16" FLAT HEAD SCREW - 10
HIDDEN CAM - 26
1F CAM DOWEL - 24 2F
CAM SCREW - 2
20F
VEXTENSION SLIDE - 2 UEXTENSION RAIL - 2
(EXTENSION SET SHOWN SEPARATED)
SILVER 1-1/4" PAN HEAD SCREW - 24
45S
PULL - 2
7K
414866 www.sauder.com/servicesPage 4
DRAWER FRONT BRACKET - 2
9G

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty carton
to avoid scratching your unit or the floor.
å NOTE: Assemble the bed in the room of its final location.
å Push twenty-four HIDDEN CAMS (1F) into the ENDS (A and B)
and UPRIGHTS (G, H, I, and J). Then, insert the metal end of a
CAM DOWEL (2F) into each HIDDEN CAM.
414866www.sauder.com/services Page 5
Do not tighten the HIDDEN CAMS in this step.
(24 used)
(24 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
A
B
G
H
I
J
G
H
I
J

å Push two HIDDEN CAMS (1F) into the
DRAWER BRACES (T).
å Turn two CAM SCREWS (20F) into the
DRAWER FRONTS (Q and R).
Step 2
414866 www.sauder.com/servicesPage 6
20F
Arrow
Arrow
1F
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
Q
R
T
T

å NOTE: This bed has the option for the DRAWERS to be on
either side.
Step 3
414866www.sauder.com/services Page 7
DRAWERS on the left
side of your bed.
DRAWERS on the right
side of your bed.
Head of the Bed
Head of the Bed

å Separate the EXTENSION SLIDES (V) from the
EXTENSION RAILS (U) as shown in the lower diagram. Be
prepared, the parts are greasy.
å Fasten two EXTENSION RAILS (U) to a DRAWER
UPRIGHT (J) as shown in the upper diagram. Use four
GOLD 5/16" FLAT HEAD SCREWS (3S).
å NOTE: One UPRIGHT (J) will not have EXTENSION RAILS
fastened to it.
å NOTE: For each EXTENSION RAIL, turn a SCREW into
the hole shown in the enlarged diagram. Then, slide the
inner cartridge of the EXTENSION RAIL in to find the other
hole that lines up with the hole in the UPRIGHTS. Turn a
SCREW into this hole.
Step 4
414866 www.sauder.com/servicesPage 8
Push the black lever in and pull the SLIDE from the RAIL.
Open end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Surface with
HIDDEN CAMS
J
U
U
U
V

å Fasten two EXTENSION RAILS (U) to the UPRIGHTS (H and I).
Use four GOLD 5/16" FLAT HEAD SCREWS (3S).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole
shown in the enlarged diagram. Then, slide the inner cartridge
of the EXTENSION RAIL in to find the other hole that lines up
with the hole in the UPRIGHTS. Turn a SCREW into this hole.
Step 5
414866www.sauder.com/services Page 9
Open end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Surface without
HIDDEN CAMS
Open end
Open end
Open end
H
I
H
I
Use the upper diagram if you are
putting the DRAWERS on the left.
Use the lower diagram if you are
putting the DRAWERS on the right.
U
U
U
U

å Using your hammer, gently tap eight PROPEL
NUTS (14M) into the holes in the HEAD END (A) as
shown in the lower diagram.
å Fasten the HEAD END (A) to the LARGE CENTER
UPRIGHTS (G). Use four BLACK 1-7/8" FLAT
HEAD SCREWS (2S).
Step 6
414866 www.sauder.com/servicesPage 10
14M
A
G
G
A
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
Finished edge
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S
These holes must be up.
HIDDEN CAMS and CAM
DOWELS at this end
(8 used)