Sauder Harbor View 417587 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-22
Français pg 23-25
Español pg 26-28
Lot # 366449 11/13/14
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Hutch
Harbor View Collection | Model 417587
Knick-knack
paddywhack,
give your stu a home.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
2-3
4
5-22
23-25
26-28
29-30
31
417587 www.sauder.com/servicesPage 2
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Part Identification
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E TOP (1)
F SHELF (1)
G BOTTOM (2)
H LARGE BACK (1)
I BACK (2)
J SMALL BACK (2)
K DOOR (2)
L VALANCE (1)
M MOLDING (2)

Part Identification
417587www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
I
J
K
L
M
G
M
K
I
J

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
417587 www.sauder.com/servicesPage 4
FELT DISC CARD - 1
1M
ANGLE BRACKET - 8
27G
BLACK 9/16" LARGE HEAD SCREW - 16
1S
BROWN 7/16" LARGE HEAD SCREW - 12
6S
BLACK 1-7/8" FLAT HEAD SCREW - 12
2S
METAL PIN - 4
1R
BLACK 1/2" FLAT HEAD SCREW - 8
11S
13H HINGE - 4
NAIL - 46
1N
HIDDEN CAM - 16
1F CAM DOWEL - 16 2F
GOLD 1" MACHINE SCREW - 2
50S
CAM COVER - 8
13P
KNOB - 2
5K

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push sixteen HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHTS (C and D), and BOTTOMS (G). Then, insert the
metal end of a CAM DOWEL (2F) into each HIDDEN CAM.
417587www.sauder.com/services Page 5
Arrow
1F
2F
(16 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
A
B
C
D
G
G

å Fasten four ANGLE BRACKETS (27G) to the ENDS (A and B).
Use four BLACK 9/16” LARGE HEAD SCREWS (1S).
å NOTE: Be sure the edges of the ANGLE BRACKETS are
even with the edges of the ENDS.
Step 2
417587 www.sauder.com/servicesPage 6
A
B
BLACK 9/16" LARGE HEAD SCREW
(4 used in this step)
1S
Surface with
HIDDEN CAMS Surface with
HIDDEN CAMS
27G
Finished edge
Finished edge
Remember:
Righty tighty.
Lefty loosey.
27G

å Fasten the MOLDINGS (M) to the ENDS (A and B). Use
four BLACK 9/16” LARGE HEAD SCREWS (1S).
å NOTE: There are no pre-drilled holes in the MOLDINGS (M).
The SCREWS will tighten into the grooves.
Step 3
417587www.sauder.com/services Page 7
BLACK 9/16" LARGE HEAD SCREW
(4 used in this step)
1S
A
B
Surface with
HIDDEN CAMS Surface with
HIDDEN CAMS
M
M
Groove
Finished edge
Finished edge

å Fasten the BOTTOMS (G) to the ENDS (A and B). Tighten
four HIDDEN CAMS.
Step 4
417587 www.sauder.com/servicesPage 8
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
A
B
G
G
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Finished edge
Finished edge
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

å Fasten the UPRIGHTS (C and D) to the BOTTOMS (G).
Tighten four HIDDEN CAMS.
Step 5
417587www.sauder.com/services Page 9
Arrow
Minimum
190 degrees
Maximum
210 degrees
G
GD
C
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
Finished edge

å Fasten the SHELF (F) to the UPRIGHTS (C and D). Use
four BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Step 6
417587 www.sauder.com/servicesPage 10
D
C
F
Finished edge
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S