Sauder Shoal Creek 411236 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Your everyday "Am I a
vampire?" checker.
Mirror
Shoal Creek Collection | Model 411236
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-20
Français pg 21-23
Español pg 24-26
Lot # 389063 03/10/16
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987

Table of Contents Assembly Tools Required
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Warranty
3
4
5-20
21-23
24-26
27
411236 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D BOTTOM (1)
E SHELF (1)
F DRAWER FRONT (2)
G DRAWER BACK (2)
H DRAWER SIDE (4)
I BACK (1)
J DRAWER BOTTOM (2)
K TOP (1)
L2 TOP/BOTTOM MOLDING (2)
M2 RIGHT MOLDING (1)
N2 LEFT MOLDING (1)
O MIRROR (1)
A
B
C
D
E
F
F
G
G
H
H
H
H
I
J
J
K
L2
L2
M2
N2 O
411236www.sauder.com/services Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
5M TAPE CARD - 4
BLACK 9/16" PAN HEAD SCREW - 14
51S
GOLD 1" MACHINE SCREW - 2
50S
BLACK 9/16" LARGE HEAD SCREW - 28
1S
BLACK 1-1/4" FLAT HEAD SCREW - 4
7S
SUPPORT PIN - 4
5R
BLACK 1-7/8" FLAT HEAD SCREW - 11
2S
MIRROR CLIP - 14
46M
7F TWIST-LOCK®FASTENER - 2
METAL PIN - 4
1R
BLACK 1/2" FLAT HEAD SCREW - 8
43S
CAM SCREW - 4
8F
NAIL - 16
1N
DRAWER FRONT
BRACKET - 4
30G
HIDDEN CAM - 4
1F
411236 www.sauder.com/servicesPage 4
KNOB - 2
32K12G METAL BRACKET - 2

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (7F) into the large holes in the ENDS (A and B).
411236www.sauder.com/services Page 5
Do not tighten the TWIST-LOCK® FASTENERS in this step.
7F
A
B

Step 2
å Push four HIDDEN CAMS (1F) into the TOP/
BOTTOM MOLDINGS (L2).
å Turn four CAM SCREWS (8F) into
the MOLDINGS (M2 and N2).
411236 www.sauder.com/servicesPage 6
M2
N2
Arrow
Hole
8F
1F
Arrow
Some assembly
(and snacks) required.
(4 used)
Do not tighten the HIDDEN CAMS in this step.
L2
L2
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.

Step 3
å Using your hammer, gently tap the SUPPORT PINS (5R)
into the holes in the ENDS (A and B) and UPRIGHT (C).
411236www.sauder.com/services Page 7
5R
5R
5R
A
B
C

Step 4
å Fasten the ENDS (A and B) to the SHELF (E). Tighten two TWIST-LOCK® FASTENERS.
å Insert four METAL PINS (1R) into the UPRIGHT (C).
å Insert the METAL PINS (1R) in one end of the UPRIGHT (C) into the holes in the SHELF (E).
411236 www.sauder.com/servicesPage 8
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the hole of the
adjoining part.
NOTE: The dowel end of the FASTENER must remain fully
inserted in the hole of the adjoining part while locking
the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight
as possible.
Dowel end
1R
1R
Finished edge
Finished edge
Surface
with holes
Unfinished edge
A
B
C
E
The support pin
must be here.

Step 5
å Fasten the BOTTOM (D) to the ENDS (A and B) and UPRIGHT (C).
Use four BLACK 1-7/8" FLAT HEAD SCREWS (2S).
å NOTE: Be sure the METAL PINS in the UPRIGHT (C) insert into the
holes in the BOTTOM (D).
411236www.sauder.com/services Page 9
Unfinished surface
Unfinished edge
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
2S
A
B
C
D

å Fasten the TOP/BOTTOM MOLDINGS (L2) to the
MOLDINGS (M2 and N2). Tighten four HIDDEN CAMS.
Step 6
411236 www.sauder.com/servicesPage 10
Unfinished surface
Unfinished surface
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
The groove must be here.
L2
L2
M2
N2
12
Side Step: Make
nachos. (Optional, but
recommended.)