Sauder Harbor View 416797 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-15
Français pg 16-17
Español pg 18-20
Lot # 362067 06/04/14
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Storage Cabinet
Harbor View Collection | Model 416797
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Store behind
closed doors.

Table of Contents Assembly Tools Required
3
4
5-15
16-17
18-20
21-22
23
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
416797 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D TOP (1)
E SHELF (1)
F BOTTOM (1)
G BACK (1)
H RIGHT DOOR (1)
I LEFT DOOR (1)
J ADJUSTABLE SHELF (4)
K SKIRT (1)
L FRONT MOLDING (1)
M RIGHT MOLDING (1)
N LEFT MOLDING (1)
Now you know
our ABCs.
416797www.sauder.com/services Page 3
A
B
C
D
E
F
G
H
I
J
K
L
M
N
J
J
J

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
416797 www.sauder.com/servicesPage 4
HIDDEN CAM - 14
1F CAM DOWEL - 14 2F
METAL BRACKET - 4
4G 13H HINGE - 4
MOLDING
CONNECTOR - 2
18F
FELT DISC CARD - 1
1M
METAL PIN - 16
1R RUBBER SLEEVE - 16 2R
SILVER 2" FLAT HEAD SCREW - 7
57S
BLACK 1-7/8" FLAT HEAD SCREW - 3
2S
BLACK 1-1/8" PAN HEAD SCREW - 2
9S
BLACK 9/16" LARGE HEAD SCREW - 9
1S
BLACK 1/2" FLAT HEAD SCREW - 8
11S
NAIL - 51
1N
93K KNOB - 2
SAFETY BRACKET - 1
1G

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push fourteen HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHT (C), SHELF (E), and BOTTOM (F). Then, insert the
metal end of a CAM DOWEL (2F) into each HIDDEN CAM.
416797www.sauder.com/services Page 5
Arrow
1F
2F
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
(14 used)
A
B
C
E
F

Step 2
å Tap two MOLDING CONNECTORS (18F) into the notches
in the MOLDINGS (L, M, and N).
416797 www.sauder.com/servicesPage 6
M
N
L
18F
18F
Flat end
Flat end
Unfinished surface
Unfinished surface
Unfinished surface
Use your hammer to tap the MOLDING CONNECTORS (18F) into the notches in the MOLDINGS.

å Flip the MOLDINGS (L, M, and N) over and fasten the
MOLDINGS to the TOP (D). Use seven SILVER 2" FLAT
HEAD SCREWS (57S).
å NOTE: Do not overtighten the SCREWS in this step.
Step 3
416797www.sauder.com/services Page 7
L
M
N
D
Surface
with
holes
Rounded edge
SILVER 2" FLAT HEAD SCREW
(7 used in this step)
57S
Curved edge
Curved edge
Remember:
Righty tighty.
Lefty loosey.

Step 4
å Fasten the LEFT END (B) to the LEFT MOLDING (N).
Tighten two HIDDEN CAMS.
å Fasten the SHELF (E) to the LEFT END (B). Tighten two
HIDDEN CAMS.
416797 www.sauder.com/servicesPage 8
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Finished edge Curved edge
D
E
B
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
L
M
N
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

å Fasten the UPRIGHT (C) to the SHELF (E). Tighten two
HIDDEN CAMS.
å Fasten the BOTTOM (F) to the LEFT END (B). Tighten two
HIDDEN CAMS.
å Fasten the BOTTOM (F) to the UPRIGHT (C). Use two
BLACK 1-7/8" FLAT HEAD SCREWS (2S).
å Fasten the RIGHT END (A) to the SHELF (E), BOTTOM (F),
and RIGHT MOLDING (M). Tighten six HIDDEN CAMS.
Step 5
416797www.sauder.com/services Page 9
Arrow
Minimum
190 degrees
Maximum
210 degrees
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
2S
Surface
with
HIDDEN
CAMS
ED
M
A
F
C
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
Finished edge
These holes
must be here.
Finished edge
B

Step 6
å Fasten four METAL BRACKETS (4G) to the ENDS (A and B) and
BOTTOM (F). Use four 9/16" LARGE HEAD SCREWS (1S).
å Fasten the SKIRT (K) to the ENDS (A and B) and BOTTOM (F).
Use four 9/16" LARGE HEAD SCREWS (1S) through the METAL
BRACKETS and into the SKIRT.
416797 www.sauder.com/servicesPage 10
A
F
B
4G
K
4G
4G
Curved edge
BLACK 9/16" LARGE HEAD SCREW
(8 used in this step)
1S
Finished surface