Sauder Palladia 422002 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-28
Français pg 29-32
Español pg 33-36
Lot # 501400 01/30/17
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Sit and surf.
Computer Desk
Palladia Collection | Model 422002

Table of Contents Assembly Tools Required
3-4
5-6
7-28
29-32
33-36
37-38
39
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
422002 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C2 SMALL RIGHT END (1)
D2 LARGE UPRIGHT (1)
E2 SMALL UPRIGHT (1)
F2 LEFT UPRIGHT (1)
G TOP (1)
H2 BOTTOM (1)
I2 MODESTY PANEL (1)
J BRACE (1)
K BASE (1)
AA END MOLDING (3)
BB BOTTOM MOLDING (1)
CC UPPER PLINTH (3)
DD LOWER PLINTH (3)
EE SMALL BACK (1)
FF LARGE BACK (1)
GG HALF DISK (3)
Now you know
our ABCs.
422002www.sauder.com/services Page 3
A
B
C2
D2 E2
F2
G
H2
I2
J
K
AA
CC
DD
EE
FF
AA
AA
BB
DD
CC
CC
DD
GG
GG
GG

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
L KEYBOARD FRONT (1)
M KEYBOARD BACK (1)
N KEYBOARD SIDE (2)
O KEYBOARD SHELF (1)
P DRAWER FRONT (1)
T LARGE DRAWER FRONT (1)
W SMALL DRAWER FRONT (1)
D34 SMALL RIGHT DRAWER SIDE (1)
D35 SMALL LEFT DRAWER SIDE (1)
D74 SMALL DRAWER BACK (1)
D78 LARGE DRAWER BACK (1)
D86 DRAWER BACK (1)
D212 RIGHT DRAWER SIDE (1)
D213 LEFT DRAWER SIDE (1)
D260 LARGE RIGHT DRAWER SIDE (1)
D263 LARGE LEFT DRAWER SIDE (1)
D707 DRAWER BOTTOM (2)
D716 SMALL DRAWER BOTTOM (1)
Now you know
our ABCs.
422002 www.sauder.com/servicesPage 4
L
M
N
O
P
T
W
N
D213
D707
D86
D78
D263
D716
D35 D74
D34
D212
D707
D260

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
422002www.sauder.com/services Page 5
EXTENSION RAIL - 2
HH EXTENSION SLIDE - 2 II
FILE ROD - 2
8B
ANGLE
BRACKET - 15
27G
BRACKET - 3
17G HINGE - 2 12H
40CB CABINET LEFT - 2 40CA CABINET RIGHT - 2
40CC DRAWER RIGHT - 2 40CD DRAWER LEFT - 2
35AW CABINET RIGHT - 1
35AZ DRAWER LEFT - 1 35AY DRAWER RIGHT - 1
35AX CABINET LEFT - 1
FILE GLIDE - 2
15B
METAL
BRACKET - 4
4G
SMALL DRAWER
FRONT BRACKET - 1
6G DRAWER FRONT BRACKET - 1
8G LARGE DRAWER
FRONT BRACKET - 2
10G
(EXTENSION SET SHOWN SEPARATED)
NAIL - 33
1N
HIDDEN CAM - 16
1F CAM DOWEL - 16 2F
KNOB SET - 5
130K

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 1-15/16" FLAT HEAD SCREW - 8
113S
30S BLACK 1-9/16" FLAT HEAD SCREW - 12
SILVER 1/2" MACHINE SCREW - 2
38S
GOLD 1" MACHINE SCREW - 1
50S
BLACK 9/16" LARGE HEAD SCREW - 54
1S
BLACK 1-1/4" FLAT HEAD SCREW - 4
7S
BLACK 7/8" MACHINE SCREW - 2
37S
BROWN 1-1/2" FLAT HEAD SCREW - 6
14S 18S SMALL BROWN 1" FLAT HEAD SCREW - 4
12S BROWN 1" FLAT HEAD SCREW - 7
3S GOLD 5/16" FLAT HEAD SCREW - 28
SILVER 5/8" FLAT HEAD SCREW - 4
23S
SILVER 9/16" LARGE HEAD SCREW - 2
54S
SMALL BLACK 1-1/4" FLAT HEAD SCREW - 2
74S
422002 www.sauder.com/servicesPage 6

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push sixteen HIDDEN CAMS (1F) into the ENDS (A, B,
and C2), UPRIGHTS (D2, E2, and F2), and BOTTOM (H2).
Then, insert the metal end of a CAM DOWEL (2F) into
each HIDDEN CAM.
A
B
C2
D2
E2
F2
H2
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
2F
(16 used)
Arrow
1F
2F
422002www.sauder.com/services Page 7
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1867
to watch a video on how to assemble your unit.

Step 2
å Separate the EXTENSION SLIDES (II) from the
EXTENSION RAILS (HH) as shown in the upper diagram
below. Be prepared, the parts are greasy.
å Fasten two EXTENSION RAILS (HH) to the SMALL RIGHT
END (C2) and SMALL UPRIGHT (E2). Use four GOLD
5/16" FLAT HEAD SCREWS (3S).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the
hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL out to find the other
hole that lines up with the hole in the END. Turn a SCREW
into this hole.
422002 www.sauder.com/servicesPage 8
Push the black lever in and pull the SLIDE from the RAIL.
II HH
C2
E2
HH
HH
Finished edge
Open end
Finished edge
Open end
Surface with
HIDDEN CAMS Surface with
HIDDEN CAMS
Remember:
Righty tighty.
Lefty loosey.
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S

å Fasten the CABINET RIGHTS (40CA) and CABINET
LEFTS (40CB) to the SMALL RIGHT END (C2) and
SMALL UPRIGHT (E2). Use eight GOLD 5/16" FLAT
HEAD SCREWS (3S) through holes #1 and #3.
Step 3
422002www.sauder.com/services Page 9
C2
E2
1
2
34
43
2
1
1
2
34
43
2
1Finished edge
Finished edge
Roller end
Roller end
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
3S
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS

Step 4
å Fasten the CABINET RIGHT (35AW) and CABINET LEFT (35AX)
to the UPRIGHTS (D2 and F2). Use four GOLD 5/16" FLAT
HEAD SCREWS (3S).
422002 www.sauder.com/servicesPage 10
D2
F2
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Roller end
Roller end
These holes must be here.
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S

å Fasten fifteen ANGLE BRACKETS (27G) to the
ENDS (A and B) and LARGE UPRIGHT (D2). Use fifteen
BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the edges of the ANGLE BRACKETS are
even with the edges of the ENDS and UPRIGHT.
å Fasten the END MOLDINGS (AA) and UPPER
PLINTHS (CC) to the ENDS (A and B) and LARGE
UPRIGHT (D2). Use fifteen BLACK 9/16" LARGE
HEAD SCREWS (1S).
Step 5
422002www.sauder.com/services Page 11
A
B
D2
AA
CC
AA
CC
AA CC
27G
27G
These edges
should be even.
Curved edge
Curved edge
Curved edge
These edges
should be even.
These edges
should be even.
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
(15 used)
BLACK 9/16" LARGE HEAD SCREW
(30 used in this step)
1S

Step 6
å Fasten the HALF DISKS (GG) to the LOWER PLINTHS (DD).
Use three BROWN 1" FLAT HEAD SCREWS (12S).
å Fasten three BRACKETS (17G) to the LEFT END (B) and
LEFT UPRIGHT (F2). Use three BLACK 9/16" LARGE
HEAD SCREWS (1S).
å Fasten a LOWER PLINTH (DD) to the LEFT END (B). Use
two BLACK 9/16" LARGE HEAD SCREWS (1S).
422002 www.sauder.com/servicesPage 12
F2
B
DD
DD
DD
GG
GG
GG
17G
DD
GG
Use bottom hole
17G
Be sure the END MOLDING is
centered on the HALF DISK (GG).
The larger hole
should be facing up.
Surface without
HIDDEN CAMS
Surface with
HIDDEN CAMS
BLACK 9/16" LARGE HEAD SCREW
(5 used for the BRACKETS)
1S
BROWN 1" FLAT HEAD SCREW
(3 used for the HALF DISKS)
12S

å Fasten the ENDS (A and B) to the TOP (G). Tighten four
HIDDEN CAMS.
Step 7
422002www.sauder.com/services Page 13
G
A
B
AA
AA
Rounded edge
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Surface
with holes

Step 8
å Fasten the SMALL RIGHT END (C2) and SMALL
UPRIGHT (E2) to the TOP (G). Tighten four HIDDEN CAMS.
422002 www.sauder.com/servicesPage 14
G
C2
E2
Finished edge
Arrow
Minimum
190 degrees
Maximum
210 degrees

å Fasten the MODESTY PANEL (I2) to the LARGE
UPRIGHT (D2) and LEFT UPRIGHT (F2). Use four BLACK
1-15/16" FLAT HEAD SCREWS (113S).
Step 9
422002www.sauder.com/services Page 15
D2
F2
I2
AA
Finished edge
Finished edge
Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS
BLACK 1-15/16" FLAT HEAD SCREW
(4 used in this step)
113S

Step 10
å Fasten the UPRIGHTS (D2 and F2) to the TOP (G). Tighten
four HIDDEN CAMS.
å Fasten the LEFT UPRIGHT (F2) to the LOWER
PLINTH (DD). Use a BLACK 9/16" LARGE HEAD
SCREW (1S) through the BRACKET and into the PLINTH.
422002 www.sauder.com/servicesPage 16
D2
F2
G
AA
I2
DD
Arrow
Minimum
190 degrees
Maximum
210 degrees
Finished edge
BLACK 9/16" LARGE HEAD SCREW
(1 used in this step)
1S

å Fasten the BOTTOM (H2) to the RIGHT END (A) and LARGE
UPRIGHT (D2). Tighten four HIDDEN CAMS.
å Fasten the BOTTOM (H2) to the SMALL RIGHT END (C2)
and SMALL UPRIGHT (E2). Use four BLACK 1-15/16" FLAT
HEAD SCREWS (113S).
å Fasten four METAL BRACKETS (4G) to the BRACE (J). Use
four BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the BRACKETS are even with the edges of
the BRACE.
å Fasten the BRACE (J) to the RIGHT END (A), LARGE
UPRIGHT (D2), and BOTTOM (H2). Use four BLACK 9/16"
LARGE HEAD SCREWS (1S).
Step 11
422002www.sauder.com/services Page 17
C2
H2
D2
A
J
J
4G
4G
4G
E2
These holes
must be here.
Arrow
Minimum
190 degrees
Maximum
210 degrees
Surface
with
HIDDEN
CAMS
BLACK 1-15/16" FLAT HEAD SCREW
(4 used in this step)
113S
BLACK 9/16" LARGE HEAD SCREW
(8 used in this step)
1S

Step 12
å Fasten the LOWER PLINTHS (DD) to the BRACE (J). Use four
BLACK 1-1/4" FLAT HEAD SCREWS (7S).
å Fasten the BASE (K) and BOTTOM MOLDING (BB) to the
BRACE (J). Use four BROWN 1" FLAT HEAD SCREWS (12S).
422002 www.sauder.com/servicesPage 18
J
BB DD
DD K
Be sure the END MOLDING is
centered against the HALF DISK
on the LOWER PLINTH (DD).
Flat end
Don't worry. It isn't
Rome. This can be built
in a day.
BLACK 1-1/4" FLAT HEAD SCREW
(4 used for the LOWER PLINTHS)
7S
BROWN 1" FLAT HEAD SCREW
(4 used for the BASE and MOLDING)
12S

å Carefully turn your unit over onto its front edges. Lay the
BACKS (EE and FF) over your unit.
å Make equal margins along the bottom and both side
edges of the BACKS (EE and FF). Push on opposite
corners of your unit if needed to make it "square".
å Fasten the BACKS (EE and FF) to your unit using
the NAILS (1N).
Step 13
422002www.sauder.com/services Page 19
EE
FF
Finished surface
Finished surface
Edge without holes
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
NAIL
(33 used in this step)
1N

Step 14
å Fasten the KEYBOARD SIDES (N) to the KEYBOARD SHELF (O).
Use four BROWN 1-1/2" FLAT HEAD SCREWS (14S).
å Fasten the KEYBOARD SIDES (N) to the KEYBOARD BACK (M).
Use two BROWN 1-1/2" FLAT HEAD SCREWS (14S).
å Fasten the KEYBOARD BACK (M) to the KEYBOARD SHELF (O).
Use two SMALL BLACK 1-1/4" FLAT HEAD SCREWS (74S).
422002 www.sauder.com/servicesPage 20
M
N
O
N
This surface should be the
same finish as this surface.
Long finished edge
Finished surface
BROWN 1-1/2" FLAT HEAD SCREW
(6 used in this step)
14S
SMALL BLACK 1-1/4" FLAT HEAD SCREW
(2 used in this step)
74S