Sauder HomePlus Collection 411967 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
411967
Base Cabinet
HomePlus Collection
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Made in the USA
Archbold, OH
English.................Page 1-16
Français...........Pages 17-18
Espanol..........Página 19-20
Lot #: 337862 04 / 13 / 11
Date Purchased: ____________________

ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Straight Edge Screwdriver
Tip Shown Actual Size
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-16
Français..............................17-18
Espanol...............................19-20
Safety .................................21-22
Warranty...................................23
Page 2 www.sauder.com/services 411967

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an
inked letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to
help identify similar parts.
A RIGHT END 1
B LEFT END 1
C TOP 1
D BOTTOM 1
E BACK 1
F DOOR 2
G ADJUSTABLE SHELF 1
H FRONT SKIRT 1
J TOP MOLDING 1
R SIDE SKIRT 2
A
B
C
D
E
F
G
H
J
R
F
R
Page 3
www.sauder.com/services411967

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
REAR FOOT - 2
K
FRONT FOOT - 2
ITWIST-LOCK®
FASTENER - 7
L
TIE
PLATE - 1
O
SAFETY
BRACKET - 1
N
MHINGE - 4
ADJUSTABLE
GLIDE - 4
S
PULL - 2
Q
PROPEL
NUT - 4
T U METAL
PIN - 4
LARGE RUBBER
SLEEVE - 1
P
VRUBBER
SLEEVE - 4
BLACK 1-7/8” FLAT HEAD SCREW - 5
WSILVER 1-1/8” FLAT HEAD SCREW - 2 X
BLACK 7/8” MACHINE SCREW - 4
YBLACK 9/16” LARGE HEAD SCREW - 2 Z
BLACK 9/16” WAFER HEAD SCREW - 4
AA BLACK 1/2” FLAT HEAD SCREW - 8 BB
NAIL - 30
CC
Page 4 www.sauder.com/services 411967

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Page 5
www.sauder.com/services411967
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
To begin assembly, push four SAUDER TWIST-LOCK® FASTENERS (L) into the large holes in the ENDS (A and B). Repeat this
step for the TOP (C).
NOTE: Do not tighten the TWIST-LOCK®FASTENERS at this time.
L
A
B
(7 used)

Fasten the ENDS (A and B) to the TOP (C). Tighten four TWIST-LOCK®FASTENERS.
2
2
S
t
e
p
Page 6 www.sauder.com/services 411967
A
B
C
Edge with
TWIST-LOCK®
FASTENERS
Surface with holes
Finished edge
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must remain
fully inserted in the hole of the adjoining part while
locking the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver
as tight as possible.
Dowel end

Fasten the BOTTOM (D) to the ENDS (Aand B). Use four BLACK 1-7/8" FLAT HEAD SCREWS (W).
3
3
S
t
e
p
Page 7
www.sauder.com/services411967
A
B
D
Rounded edge
W
BLACK 1-7/8” FLAT HEAD SCREW
(4 used in this step)
Unfinished surface

Fasten the TOP MOLDING (J) to the TOP (C). Tighten three TWIST-LOCK®FASTENERS.
Slip a LARGE RUBBER SLEEVE (P) over the TIE PLATE (O). The RUBBER SLEEVE will be a tight fit.
Then, fasten the TIE PLATE (O) to the TOP MOLDING (J). Use a BLACK 9/16" LARGE HEAD SCREW (Z).
4
4
S
t
e
p
Page 8 www.sauder.com/services 411967
J
C
O
P
Wide edge
BLACK 9/16” LARGE HEAD SCREW
(1 used for the TIE PLATE)
Z

5
5
S
t
e
p
Page 9
www.sauder.com/services411967
Slide the FEET (I and K) into the notches in the SKIRTS (H and R).
Use a hammer to drive a PROPEL NUT (T) into the holes in the FEET (I and K). Now, turn an ADJUSTABLE GLIDE (S) into each
PROPEL NUT.
S
(4 used)
T
H
R
R
I
K
I
K

6
6
S
t
e
p
Page 10 www.sauder.com/services 411967
Fasten the SKIRTS (H and R) to the BOTTOM (D). Use four BLACK 9/16" WAFER HEAD SCREWS (AA) through the FEET and
into the BOTTOM.
NOTE: To raise a corner of the unit, turn the ADJUSTABLE GLIDE counter-clockwise. To lower a corner, turn theADJUSTABLE
GLIDE clockwise.
H
R
R
D
BLACK 9/16” WAFER HEAD SCREW
(4 used in this step)
AA