Sauder Whitaker Point 429374 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-34
Français pg 35-39
Español pg 40-44
Lot # 573742 10/05/21
Purchased: __________________
Lateral File
Whitaker Point Collection | Model 429374
Get all organized
and stu.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4-5
6
6-34
35-39
40-44
45-46
47
Page 2 www.sauder.com/service 429374
Adjustable Wrench

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LEFT END (1)
B RIGHT END (1)
C TOP (1)
D BOTTOM (1)
E SMALL BACK (1)
F LARGE BACK (1)
G UPPER DRAWER FRONT (1)
H LEFT DRAWER SIDE (2)
J UPPER RIGHT DRAWER SIDE (1)
K DRAWER BACK (2)
L DRAWER BOTTOM (2)
M DRAWER BRACE (2)
N LOCKING DRAWER FRONT (1)
P LOWER RIGHT DRAWER SIDE (1)
Q BALLAST (1)
Page 3www.sauder.com/service429374
A
B
C
D
E
F
G
H
J
K
L
M
N
Q
P
M
H
K
L

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
(EXTENSION SET SHOWN SEPARATED)
LONG FILE
GLIDE - 2
4
SHORT FILE
GLIDE - 4
32 EXTENSION
SLIDE - 4
1EXTENSION
RAIL - 4
CAM SCREW - 36
9LOCK PACK - 1 12
INTERLOCK
MECHANISM - 1
10 DRAWER
ACTUATOR - 2
11
FILE BAR - 4
5FRONT FILE
GLIDE - 2
6LARGE HIDDEN
CAM - 26
7SMALL HIDDEN
CAM - 10
8
LARGE WOOD
DOWEL - 25
13 SMALL WOOD
DOWEL - 20
14 PULL - 2 15
Page 4 www.sauder.com/service 429374

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
LARGE BRACKET - 1
17 SMALL BRACKET - 1 18
1/2" MACHINE SCREW - 4
21
16 SILVER 1/2" PAN HEAD SCREW - 9
23 BLACK 1/2" PAN HEAD SCREW - 12
24 3/8" PAN HEAD SCREW - 24
1-1/2" FLAT HEAD SCREW - 10
19 1" FLAT HEAD SCREW - 4
20
Page 5www.sauder.com/service429374
APPLIQUE CARD - 1
22

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 6 www.sauder.com/service 429374

Step 1
å NOTE: Save some packing foam to be used later in assembly.
å Assemble your unit on a carpeted floor or on the empty carton to
avoid scratching your unit or the floor.
å Push four LARGE HIDDEN CAMS (7) into the SMALL BACK (E).
å NOTE: Be sure to completely insert the HIDDEN CAMS into the holes.
å Turn three CAM SCREWS (9) into the SMALL BACK (E).
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
Page 7www.sauder.com/service429374
1
9
E
7
Arrow
Arrow
7

å Fasten the BALLAST (Q) to the SMALL BACK (E). Use
four 1" FLAT HEAD SCREWS (20).
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Step 2
Page 8 www.sauder.com/service 429374
Q
E
Surface with larger holes
The screwhead should
sink down into the larger
hole and be flush with the
surface of the BALLAST.
The CAM SCREW is
closer to this edge.
The hole is closer
to this edge.
1" FLAT HEAD SCREW
(4 used in this step)
20
Some assembly
(and snacks) required.

å Push seven LARGE HIDDEN CAMS (7) into the LARGE BACK (F).
å Insert three LARGE WOOD DOWELS (13) into the LARGE BACK (F).
å Push the WOOD DOWELS in the edge of the LARGE BACK (F) into
the edge of the SMALL BACK (E).
å NOTE: The LARGE BACK (F) will slide under the BALLAST (Q).
Step 3
Page 9www.sauder.com/service429374
1
7
Arrow
7
Arrow
Arrow
7
13
F
E
F
Edge with
HIDDEN CAMS
Q

å Push nine LARGE HIDDEN CAMS (7) into the BOTTOM (D).
å Insert three LARGE WOOD DOWELS (13) into the SMALL BACK (E).
å Fasten the BOTTOM (D) to the SMALL BACK (E). Tighten three HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the BACK insert into the BOTTOM.
Step 4
Page 10 www.sauder.com/service 429374
1
Arrow
7
7
Arrow
7
Arrow
13
E
D
D
Surface with HIDDEN CAMS