Sauder International Lux 421434 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-445-1527.
Share your journey!
sauder.com
Bookcase
International Lux Collection | Model 421434
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-12
Français pg 13-14
Español pg 15-16
Lot #: 503245
Date Purchased: __________________
04/25/17
Be sure to give us a ring before
making any returns. 1-800-445-1527
Here's one for
the books.

Table of Contents Assembly Tools Required
3
4
4-12
13-14
15-16
17-18
19
Hardware Identification
Part Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Page 2 www.sauder.com 421434
Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
GOLD 1/2" FLAT HEAD SCREW - 20
3
1GOLD 1" FLAT HEAD SCREW - 8 GOLD 1/2" ALLEN HEAD SCREW - 8
2
ALLEN WRENCH - 1
4FURNITURE TIPPING RESTRAINT KIT - 1
99

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A END (2)
B FRONT TOP (1)
C REAR TOP (1)
D TOP BRACE (2)
E TOP/BOTTOM SHELF (2)
F SHELF (3)
G REAR BRACE (2)
H GLASS SHELF (5)
Now you know
our ABCs.
Page 3www.sauder.com421434
A
B
CD
E
F
G
H
F
F
E
D
A
G
H
H
H
H

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Fasten the TOPS (B and C) to the TOP BRACES (D).
Tighten four GOLD 1/2" ALLEN HEAD SCREWS (2) using
the ALLEN WRENCH (4).
Page 4 www.sauder.com 421434
B
C
D
D
GOLD 1/2" ALLEN HEAD SCREW
(4 used in this step)
2
4
This hole must be here.
Remember:
Righty tighty.
Lefty loosey.

StepStep 2
å Fasten the ENDS (A) to the TOPS (B and C). Tighten
four GOLD 1/2" ALLEN HEAD SCREWS (2) using the
ALLEN WRENCH (4).
Page 5www.sauder.com421434
A
B
C
A
GOLD 1/2" ALLEN HEAD SCREW
(4 used in this step)
2
4
This hole must be here.
These holes must be here.

Step
å Insert one of the TOP/BOTTOM SHELVES (E) through
the ENDS (A).
å Fasten the TOP/BOTTOM SHELF (E) to the ENDS (A).
Use four GOLD 1" FLAT HEAD SCREWS (1).
Step 3
Page 6 www.sauder.com 421434
A
EA
A
E
A
GOLD 1" FLAT HEAD SCREW
(4 used in this step)
1
These holes must be here.

StepStep 4
å Insert the SHELVES (F) through the ENDS (A).
å Fasten the SHELVES (F) to the ENDS (A). Use twelve
GOLD 1/2" FLAT HEAD SCREWS (3).
Page 7www.sauder.com421434
A
F
A
A
A
F
F
F
F
F
These holes must be here.
GOLD 1/2" FLAT HEAD SCREW
(12 used in this step)
3

Step
å Insert the remaining TOP/BOTTOM SHELF (E) through
the ENDS (A).
å Fasten the TOP/BOTTOM SHELF (E) to the ENDS (A).
Use four GOLD 1" FLAT HEAD SCREWS (1).
Step 5
Page 8 www.sauder.com 421434
GOLD 1" FLAT HEAD SCREW
(4 used in this step)
1
A
E
A
These holes must be here.
A
E
A

StepStep 6
å Fasten the REAR BRACES (G) to the ENDS (A). Use eight
GOLD 1/2" FLAT HEAD SCREWS (3).
å NOTE: The tabs on the REAR BRACES must face up so
the REAR BRACES rest down inside the ENDS.
Page 9www.sauder.com421434
GOLD 1/2" FLAT HEAD SCREW
(8 used in this step)
3
A
A
The tab must face up.
These surfaces
should be even.
G
G

Step 7
å Carefully stand your unit upright.
å We recommend using the FURNITURE TIPPING
RESTRAINT KIT (99) for added stability. Fasten a bracket
to the back edge of the REAR TOP (C) using the 5/8"
screw as shown.
å Place your unit in its final location against a wall.
å Follow the instructions included in the KIT to fasten your
unit to the wall.
Page 10 www.sauder.com 421434
99
Use the 5/8" screw through the
small hole in a bracket and into the
back edge of the REAR TOP (C).
Small hole
C
If you're doing this to
help a friend, don't
leave without a bite.