Sauder Cannery Bridge 429414 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
English pg 1-38
Français pg 39-43
Español pg 44-48
Lot # 569300 08/03/21
Purchased: __________________
Executive Desk
Cannery Bridge Collection | Model 429414
Go all Wall Street
on everyone.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4
5
6-38
39-43
44-48
49-50
51
Page 2 www.sauder.com/service 429414

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A LEFT END (1)
B RIGHT END (1)
C LEFT UPRIGHT (1)
D RIGHT UPRIGHT (1)
E TOP (1)
F BOTTOM (2)
G MODESTY PANEL (1)
H BACK (2)
K BASE (2)
L SMALL DRAWER FRONT (4)
M SMALL LEFT DRAWER SIDE (4)
N SMALL RIGHT DRAWER SIDE (4)
O SMALL DRAWER BACK (4)
P SMALL DRAWER BOTTOM (4)
Q LARGE DRAWER FRONT (2)
R LARGE LEFT DRAWER SIDE (2)
S LARGE RIGHT DRAWER SIDE (2)
T LARGE DRAWER BACK (2)
U LARGE DRAWER BOTTOM (2)
A
B
C
D
E
F
F
G
H
H
K
K
L
L
L
L
M
M
M
M
N
N
O
O
O
O
P
P
P
P
Q
R
S
T
U
QR
S
T
U
N
N
Page 3www.sauder.com/service429414

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
(EXTENSION SET SHOWN SEPARATED)
1SMALL EXTENSION
RAIL - 8 2SMALL EXTENSION SLIDE - 8
(EXTENSION SET SHOWN SEPARATED)
3LARGE EXTENSION
RAIL - 4 4LARGE EXTENSION SLIDE - 4
CAM SCREW - 72
11 PULL - 6 12
LARGE HIDDEN
CAM - 56
9SMALL HIDDEN
CAM - 16
10
7/8" MACHINE SCREW - 6
25
1-1/2" FLAT HEAD SCREW - 16
24
1/2" PAN HEAD SCREW - 16
22
3/8" FLAT HEAD SCREW - 76
20
6FILE HANGER - 4
FILE GLIDE - 4
5LARGE WOOD
DOWEL - 44
7SMALL WOOD
DOWEL - 48
8
METAL BRACKET - 8
15 GROMMET
WITH CAP- 2
19
APPLIQUE CARD - 1
16
Page 4 www.sauder.com/service 429414

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Page 5www.sauder.com/service429414

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
A
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Turn seven CAM SCREWS (11) into the LEFT END (A).
å Push four HIDDEN CAMS (9) into the LEFT END (A).
11
11
9
Arrow
Page 6 www.sauder.com/service 429414
1

Step 2
A
å Separate the SMALL EXTENSION SLIDES (2) from the SMALL EXTENSION RAILS (1) as shown in the upper diagram
below. Be prepared, the parts are greasy.
å Fasten two EXTENSION RAILS (1) to the LEFT END (A). Use six 3/8" FLAT HEAD SCREWS (20).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL in to find the other holes that lines up with the holes in the LEFT END. Turn a
SCREW into these holes.
å NOTE: The SMALL EXTENSION SLIDES will be used later for the SMALL DRAWERS.
3/8" FLAT HEAD SCREW
(6 used in this step)
20
Push the black lever and pull the SLIDE from the RAIL.
1
2
1
1
Open end
Page 7www.sauder.com/service429414
7

Step 3
A
å Separate the LARGE EXTENSION SLIDES (4) from the LARGE EXTENSION RAILS (3) as shown in the upper diagram
below. Be prepared, the parts are greasy.
å Fasten a LARGE EXTENSION RAIL (3) to the LEFT END (A). Use four 3/8" FLAT HEAD SCREWS (20).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL in to find the other holes that lines up with the holes in the LEFT END. Turn a
SCREW into these holes.
å NOTE: The LARGE EXTENSION SLIDES will be used later for the LARGE DRAWERS.
3
3/8" FLAT HEAD SCREW
(4 used in this step)
20
Push the black lever and pull the SLIDE from the RAIL.
3
4
Open end
7
Page 8 www.sauder.com/service 429414

Step 4
K
K
F
F
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
1
Arrow
9
å Push twelve LARGE HIDDEN CAMS (9) into a BOTTOM (F)and a BASE (K).
å Turn two CAM SCREWS (11) into the BASE (K).
å Insert two LARGE WOOD DOWELS (7) into the BASE (K).
å Fasten the BASE (K) to the BOTTOM (F). Tighten two LARGE HIDDEN CAMS.
å NOTE: Be sure the LARGE WOOD DOWELS in the BASE insert into the BOTTOM.
9
Arrow
9
Arrow
9
Arrow
Arrow
9
11
Surface with HIDDEN CAMS
7
Page 9www.sauder.com/service429414

å Push four LARGE HIDDEN CAMS (9) into a BACK (H).
å Insert two LARGE WOOD DOWELS (7) into the edge of
the BOTTOM (F)
å Push the BACK (H) onto the LARGE WOOD DOWELS (7)
in the BOTTOM (F).
Step 5
F
H
H
9
Arrow
Arrow
9
7
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
Page 10 www.sauder.com/service 429414
1