Sauder Lateral File Boulevard Cafe 427345 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-445-1527.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey!
Enlish p 1-22
Français p 23-25
Español p 26-28
Lot # 552680 08/26/20
Purchased: __________________
Lateral File
Boulevard Cafe Collection | Model 427345
Get all organized
and stu.

Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
Hammer
Not actual size
3
4-5
6
7-22
23-25
26-28
29-30
31
Pae 2 www.sauder.com/service 427345

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A TOP (1)
B LEFT END (1)
C RIGHT END (1)
D LEFT BACK (1)
E RIGHT BACK (1)
F DRAWER FRONT (2)
G DRAWER BACK (2)
H LEFT DRAWER SIDE (2)
J DRAWER BOTTOM (2)
K DRAWER BRACE (2)
L LOWER FRONT BRACE (1)
M UPPER FRONT BRACE (1)
N LOWER BACK BRACE (1)
P RIGHT DRAWER SIDE (2)
Q UPPER BACK BRACE (1)
Pae 3www.sauder.com/service427345
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
F
G
H
J
K
P

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Pae 4 www.sauder.com/service 427345
EXTENSION SET SHOWN SEPARATED
1EXTENSION RAIL - 4 2EXTENSION SLIDE - 4 3FRONT FILE
GLIDE  2
4LONG FILE
GLIDE - 2 5SHORT FILE GLIDE - 4 6FILE HANGER  4
CAM SCREW - 10
8LARGE WOOD
DOWEL - 2
9
SMALL WOOD
DOWEL - 18
10 HOOK - 2 11 PULL - 2 12
L-WRENCH - 2
15
APPLIQUE CARD - 2
13 STRAP - 2 14
HIDDEN CAM - 10
7

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Pae 5www.sauder.com/service427345
9/16" PAN HEAD SCREW - 18
19
1-3/4" HEX HEAD SCREW - 4
16 1-1/2" FLAT HEAD SCREW - 12 17
1/2" MACHINE SCREW - 4
20
3/8" FLAT HEAD SCREW - 24
22
1-1/2" HEX HEAD SCREW - 8
18
3/8" HEX HEAD SCREW - 4
21
NUT - 4
23

HOW TO USE A HIDDEN CAM & CAM SCREW OR CAM DOWEL
NOTE: Various CAM SCREWS or a CAM DOWEL may be used.
Cam Screws Cam Dowel
Turn the CAM SCREW or
gently tap the CAM DOWEL
until the shoulder is against
the surface of the part.
1.
Hidden CamHidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2.
3.
1
2
Insert the CAM SCREW or CAM DOWEL into the
HIDDEN CAM. Tighten the HIDDEN CAM.
Hardware Usae Guide
Pae 6 www.sauder.com/service 427345

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to avoid scratchin your unit or the floor.
å Separate the EXTENSION SLIDES (2) from the EXTENSION RAILS (1) as shown in the upper diaram below. Be
prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (1) to the ENDS (B and C). Use twelve 3/8" FLAT HEAD SCREWS (22) throuh the
exact holes shown.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the 1st hole shown in the enlared diaram. Then, slide the
inner cartride of the EXTENSION RAIL in to find the other two holes that line up with the holes in the END. Turn a
SCREW into each of these holes.
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
Pae 7www.sauder.com/service427345
B
C
Slide the black lever, and pull the SLIDE from the RAIL.
12
1st
1st
1st
Open end
Open end
1
1
7
3/8" FLAT HEAD SCREW
(12 used in this step)
22
1st
1st
1
1

å Fasten the BACK BRACES (N and Q) to the LEFT
END (B). Tihten two 1-1/2" HEX HEAD SCREWS (18)
usin the L-WRENCH (15).
Step 2
Pae 8 www.sauder.com/service 427345
15
BN
Q
The EXTENSION RAILS
are closer to this ede.
1-1/2" HEX HEAD SCREW
(2 used in this step)
18
Ede with three tabs
Ede with four tabs
Surface with holes
Some assembly
(and snacks) required.

å Fasten the FRONT BRACES (L and M) to the LEFT
END (B). Tihten two 1-1/2" HEX HEAD SCREWS (18)
usin the L-WRENCH (15).
Step 3
Pae 9www.sauder.com/service427345
15
1-1/2" HEX HEAD SCREW
(2 used in this step)
18
B
L
MThe tabs face down and
are closer to this surface.

å Fasten the RIGHT END (C) to the BRACES (L, M, N,
and Q). Tihten four 1-1/2" HEX HEAD SCREWS (18)
usin the L-WRENCH (15).
Step 4
Pae 10 www.sauder.com/service 427345
15
N
QL
M
C
1-1/2" HEX HEAD SCREW
(4 used in this step)
18

å Connect the BACKS (D and E) toether by insertin
two LARGE WOOD DOWELS (9) into the holes in the
BACKS (D and E) as shown.
å Turn the HOOKS (11) into the BACKS (D and E) until
they are snu.
å NOTE: The open side of the HOOK should face the
short ede of the BACK.
Step 5
Pae 11www.sauder.com/service427345
E
D
9
11
Surface with holes Surface with holes
Ede with holes

å Fasten the LOWER BACK BRACE (N) to the BACKS (D
and E). Tihten four 1-3/4" HEX HEAD SCREWS (16)
usin the L-WRENCH (15).
å NOTE: You should start each SCREW a few turns before
completely tihtenin any of them.
å Fasten the UPPER BACK BRACE (Q) to the BACKS (D
and E). Use four 9/16" PAN HEAD SCREWS (19).
Step 6
Pae 12 www.sauder.com/service 427345
N
E
D
15
9/16" PAN HEAD SCREW
(4 used for the UPPER BRACE)
19
Q
1-3/4" HEX HEAD SCREW
(4 used for the LOWER BRACE)
16

å Fasten the TOP (A) to the UPPER BRACES (M and Q). Use
six 9/16" PAN HEAD SCREWS (19).
å NOTE: You should start each SCREW a few turns before
completely tihtenin any of them.
Step 7
Pae 13www.sauder.com/service427345
Q
A
Surface with holes
M
9/16" PAN HEAD SCREW
(6 used in this step)
19

å Push ten HIDDEN CAMS (7) into the DRAWER
SIDES (H and P) and DRAWER BRACES (K).
Step 8
Pae 14 www.sauder.com/service 427345
1
P
K
H
7
Arrow
P
K
H
Now miht be a
ood time to refresh
your drink.

å Insert four SMALL WOOD DOWELS (10) into the DRAWER BACK (G).
å Fasten the DRAWER SIDES (H and P) to the DRAWER BACK (G). Use
four 1-1/2" FLAT HEAD SCREWS (17).
å Fasten the DRAWER BRACE (K) to the DRAWER BACK (G). Use two
1-1/2" FLAT HEAD SCREWS (17).
å Slide the DRAWER BOTTOM (J) into the rooves in the DRAWER
SIDES (H and P) and DRAWER BACK (G).
å Repeat this step for the other drawer.
Step 9
Pae 15www.sauder.com/service427345
J
G
K
P
H
G
Groove
Be sure the
DRAWER
BOTTOM
inserts into
the DRAWER
BACK roove.
10
10 (8 used)
1-1/2" FLAT HEAD SCREW
(12 used in this step)
17
Surface with
HIDDEN CAM
P
H

å Turn five CAM SCREWS (8) into the DRAWER FRONT (F).
å Insert five SMALL WOOD DOWELS (10) into the DRAWER
SIDES (H and P) and DRAWER BRACE (K).
å Fasten the DRAWER FRONT (F) to the DRAWER SIDES (H
and P) and DRAWER BRACE (K). Tihten five HIDDEN CAMS.
å Repeat this step for the other drawer.
Step 10
Pae 16 www.sauder.com/service 427345
1
8
F
(10 used)
Be sure the
DRAWER
BOTTOM
inserts into
the DRAWER
FRONT roove.
F
K
P
H
10
(10 used)

å Fasten two EXTENSION SLIDES (2) to the DRAWER
SIDES (H and P). Use six 3/8" FLAT HEAD SCREWS (22)
in the exact holes shown.
å Fasten one PULL (12) to the DRAWER FRONT (F). Use two
1/2" MACHINE SCREWS (20).
å Repeat this step for the other drawer.
Step 11
Pae 17www.sauder.com/service427345
2Open end
2
2
F
12
H
P
3/8" FLAT HEAD SCREW
(12 used for the SLIDES)
22
Open end
Open end
1/2" MACHINE SCREW
(4 used for the PULLS)
20

å Fasten one FRONT FILE GLIDE (3) to the DRAWER FRONT (F). Use
four 9/16" PAN HEAD SCREWS (19).
å Press a LONG FILE GLIDE (4) onto the DRAWER BACK (G).
å NOTE: The file tabs on the GLIDES should face each other.
å Press two SHORT FILE GLIDES (5) onto the DRAWER SIDES (H and P).
å Place two FILE HANGERS (6) onto the FILE GLIDES (3 and 4).
å Repeat this step for the other drawer.
Step 12
Pae 18 www.sauder.com/service 427345
9/16" PAN HEAD SCREW
(8 used in this step)
19
3
4
H
F
P
G
5
5
3
4
6
6
File tab

å Fasten the STRAPS (14) to the DRAWER BACK (G). From
the back of the DRAWER, tihten two 3/8" HEX HEAD
SCREWS (21) throuh the STRAPS (14), throuh the
DRAWER BACK (G), and into the NUTS (23) usin both
L-WRENCHES (15).
Step 13
Pae 19www.sauder.com/service427345
G
14
14
3/8" HEX HEAD SCREW
(2 used in this step)
21
15
15
23
If you're doin this to
help a friend, don't
leave without a bite.

å Carefully stand your unit upriht.
å To insert the upper DRAWER with the STRAPS into your unit, line up the EXTENSION SLIDES on the drawer with the
EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push
in hard until it is all the way in, then it will slide in and out easier.
å Feed the STRAPS (14) throuh the HOOKS as shown.
å NOTE: You may need to carefully lay your unit down.
Step 14
Pae 20 www.sauder.com/service 427345
14
14
14
HOOK
The STRAPS are a safety feature that
prevents more than one drawer from
opening at the same time. Do not use
excessive force to open the drawers.