Sauder Pogo 417146 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-22
Français p 23-25
Español p 26-28
Lot # 372801 06/01/15
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
Chiorobe
Poo Collection | 417146
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.
Adult assembly required.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4-5
6-22
23-25
26-28
29-30
31
417146 www.sauder.com/servicesPae 2

Now you know
our ABCs.
Part Identification
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D TOP (1)
D12 SMALL RIGHT DRAWER SIDE (1)
D13 SMALL LEFT DRAWER SIDE (1)
D30 LARGE RIGHT DRAWER SIDE (3)
D31 LARGE LEFT DRAWER SIDE (3)
D68 LARGE DRAWER BACK (3)
D128 SMALL DRAWER BACK (1)
D733 DRAWER BOTTOM (4)
E2 BOTTOM (1)
F LARGE BACK (1)
G SMALL BACK (1)
H DOOR (1)
I ADJUSTABLE SHELF (1)
J SKIRT (1)
K LARGE DRAWER FRONT (3)
L SMALL DRAWER FRONT (1)
M TOP MOLDING (1)
N BALLAST (1)
M67 BRACE (4)
A
B
C
D
E2
F
G
H
I
J
K
L
M
N
D12
D30
D31
D13
D68
D128
D733
D733
417146www.sauder.com/services Pae 3
M67
M67
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.

åScrews are shown actual size. You may receive extra hardware with your unit.
Hardware Identification
WASHER - 1
13M
19A ROD HANGER - 2 10A SLIDE CAM - 8
22H
HINGE SPACER -2
14H HINGE - 2
DOOR STOP - 1
4I
HIDDEN CAM - 14
1F
CAM DOWEL - 14
2F
SAFETY STRAP - 1
Locate this nylon SAFETY
STRAP (60M) to be used
later in assembly. Do not
accidentally throw away.
60M SAFETY DRYWALL
ANCHOR - 1
61M
CLEAR KNOB - 9
107K
5L WARNING LABEL - 1
(Refer to Step 16 for proper
location and application)
WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Place heaviest items in the lowest drawers.
• Unless specifically desined to accommodate, do not
set TVs or other heavy objects on top of this product.
• Never allow children to climb or han on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
• If equipped with a drawer interlock system, do not
defeat or remove it.
Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
This is a permanent label. Do not attempt to remove!
04/10 332296
UNIVERSAL CABINET RAIL - 8
35AA
417146 www.sauder.com/servicesPae 4
KNOB - 9
60K
METAL BRACKET - 5
4G
35AC DRAWER RIGHT - 435AD DRAWER LEFT - 4
ROD - 1
17A

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 1-1/8" PAN HEAD SCREW - 13
9S
SILVER 3/4" MACHINE SCREW - 9
20S
BLACK 9/16" LARGE HEAD SCREW - 11
1S
SHELF SNAP - 4
8R
BROWN 1-1/2" FLAT HEAD SCREW - 3
14S
3S GOLD 5/16" FLAT HEAD SCREW - 34
METAL PIN - 4
1R
SILVER 5/8" FLAT HEAD SCREW - 4
23S
SILVER 1/2" FLAT HEAD SCREW - 2
78S
NAIL - 58
1N
30S BLACK 1-9/16" FLAT HEAD SCREW - 20
417146www.sauder.com/services Pae 5
BLACK 1-15/16" FLAT HEAD SCREW - 2
113S

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
417146 www.sauder.com/servicesPae 6
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push fourteen HIDDEN CAMS (1F) into the ENDS (A and B)
UPRIGHT (C), BOTTOM (E2), and DRAWER BRACES (M67).
Then, insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM.
Arrow
1F
2F
(14 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tihten the HIDDEN CAMS in this step.
A
B
C
E2
M67
M67
M67
M67

Step 2
417146www.sauder.com/services Pae 7
å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the
RIGHT END (A) and UPRIGHT (C). Use sixteen GOLD 5/16"
FLAT HEAD SCREWS (3S) throuh holes #1 and #3.
å *patent pendin lide system
GOLD 5/16" FLAT HEAD SCREW
(16 used in this step)
3S
Glide end
3
2
1
1
2
3
Glide end
3
2
1
1
2
3
3
2
1
1
2
3
3
2
1
1
2
3
A
C
Remember:
Rihty tihty.
Lefty loosey.

å Flip the UPRIGHT (C) over.
å Fasten the ROD HANGERS (19A) to the UPRIGHT (C) and LEFT
END (B). Use two SILVER 1/2" FLAT HEAD SCREWS (78S).
Step 3
417146 www.sauder.com/servicesPae 8
SILVER 1/2" FLAT HEAD SCREW
(2 used in this step)
78S
19A
B
C

å Fasten the LEFT END (B) and UPRIGHT (C) to the TOP (D).
Tihten four HIDDEN CAMS.
Step 4
417146www.sauder.com/services Pae 9
B
C
D
Notch
Finished ede
Start Tihten
Arrow
Minimum
190 derees
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Arrow
Maximum
210 derees
Surface
with holes
Rounded ede

å Fasten the BOTTOM (E2) to the LEFT END (B). Tihten
two HIDDEN CAMS.
å Fasten the BOTTOM (E2) to the UPRIGHT (C). Use two
BLACK 1-15/16" FLAT HEAD SCREWS (113S).
å Push a DOOR STOP (4I) into the hole near the notch in
the UPRIGHT (C).
Step 5
417146 www.sauder.com/servicesPae 10
Surface with HIDDEN CAMS
B
C
E2
Arrow
Minimum
190 derees
Maximum
210 derees
4I
BLACK 1-15/16" FLAT HEAD SCREW
(2 used in this step)
113S

å Fasten the RIGHT END (A) to the TOP (D) and BOTTOM (E2).
Tihten four HIDDEN CAMS.
å Fasten the TOP MOLDING (M) to the TOP (D). Use three
BROWN 1-1/2" FLAT HEAD SCREWS (14S).
å NOTE: Do not overtihten the SCREWS into the TOP.
Step 6
417146www.sauder.com/services Pae 11
A
D
E2
M
BROWN 1-1/2" FLAT HEAD SCREW
(3 used in this step)
14S
Curved ede
Arrow
Minimum
190 derees
Maximum
210 derees
Do not overtihten
the SCREWS (14S).

å Fasten three METAL BRACKETS (4G) to the BOTTOM (E2)
and a METAL BRACKET to each END (A and B). Use five
BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the BRACKETS are even with the edes of
the ENDS and BOTTOM.
å Fasten the SKIRT (J) to the BOTTOM (E2). Use five
BLACK 9/16" LARGE HEAD SCREWS (1S).
å Fasten the BALLAST (N) to the BOTTOM (E2). Use four
BLACK 1-1/8" PAN HEAD SCREWS (9S).
Step 7
417146 www.sauder.com/servicesPae 12
A
B
E2
J
Finished surface
BLACK 1-1/8" PAN HEAD SCREW
(4 used in this step)
9S
BLACK 9/16" LARGE HEAD SCREW
(10 for the METAL BRACKETS)
1S
N
Don't worry. It isn't
Rome. This can be built
in a day.
4G
4G
4G

Step 8
417146www.sauder.com/services Pae 13
å Carefully turn your unit over onto its front edes. Lay the SMALL
BACK (G) over the small openin of your unit.
å Make equal marins alon all four edes of the SMALL BACK (G). Push
on opposite corners of your unit if needed to make it "square".
å Fasten the SMALL BACK (G) to your unit usin twenty-four NAILS (1N).
å Unfold the LARGE BACK (F) and lay it over the lare openin. Make
equal marins alon three edes of the LARGE BACK. Push on opposite
corners of your unit if needed to make it "square".
å NOTE: The LARGE BACK will overlap the SMALL BACK.
å Fasten the LARGE BACK (F) to your unit usin the remainin NAILS (1N).
å NOTE: A perforation has been provided for access throuh the BACK.
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution
Unfinished surface
NAIL
(58 used in this step)
1N
Perforation
G
Printed information
must be facin up.
F

å Fasten two HINGES (14H) and two HINGE SPACERS (22H)
to the DOOR (H). Use four SILVER 5/8" FLAT
HEAD SCREWS (23S).
Step 9
417146 www.sauder.com/servicesPae 14
SILVER 5/8" FLAT HEAD SCREW
(4 used in this step)
23S
14H
22H
H

å Carefully stand your unit upriht.
å Before fastenin the DOOR to your unit, be sure the
mountin screw is aainst the stops as shown in the riht
diaram. If it isn't, loosen the mountin screw to slide it
aainst the stops. Then tihten the mountin screw.
å Fasten the DOOR (H) to the LEFT END (B) Use the screws
in the HINGE. See the next step for door adjustments.
å You have the option of fastenin a WOOD KNOB (60K) or
a CLEAR KNOB (107K) to the DOOR (H).
å Fasten a CLEAR KNOB (107K) to the DOOR (H) with a
SILVER 3/4" MACHINE SCREW (20S) or fasten a WOOD
KNOB (60K) to the DOOR (H) with a BLACK 1-1/8" PAN
HEAD SCREW (9S).
Step 10
417146www.sauder.com/services Pae 15
SILVER 3/4" MACHINE SCREW
(1 used for the METAL KNOB)
20S
H
107K
B
Mountin
screw
Stop
Hine
BLACK 1-1/8" PAN HEAD SCREW
(1 used in this step)
9S
60K

Step 11
417146 www.sauder.com/servicesPae 16
å Refer to the enlared diaram to identify the parts on
the HINGES.
å The DOORS may need some adjustments. Follow the text
below to make needed adjustments.
å DOOR ADJUSTMENTS:
To adjust the DOORS from side to side (horizontal), loosen the
mountin screw several turns, then turn the adjustin screw in
or out. Tihten the mountin screw after makin adjustments.
å To adjust the DOORS up and down (vertical), loosen both
vertical adjustment screws. Move the DOORS up or down to the
desired location. Tihten the screws after makin adjustments.
å To adjust the DOORS in or out (depth), loosen the mountin
screw one turn and move the DOORS in or out, as needed.
Tihten the mountin screw after makin adjustments.
Adjustin screw (horizontal) Mountin screw (depth)
(vertical adjustment)

Step 12
417146www.sauder.com/services Pae 17
å Insert the DRAWER SIDES (D30 and D31) at an angle
into the slot at each end of the DRAWER FRONT (K). å Slide the DRAWER BOTTOM (D733) into the
grooves in the DRAWER SIDES (D30 and D31) and
DRAWER FRONT (K).
å Fasten the DRAWER BRACE (M67) to the
DRAWER FRONT (K). Tighten one HIDDEN CAM. å Fasten the DRAWER BACK (D68) to the DRAWER
SIDES (D30 and D31) and DRAWER BRACE (M67). Use
five BLACK 1-9/16" FLAT HEAD SCREWS (30S). Repeat
this step for the remaining drawers.
The tabs should insert freely
into the slots. Gently tilt the
DRAWER SIDES side to side
until the tabs slip into the slots.
12
34
Be sure the DRAWER
BOTTOM inserts into the
DRAWER FRONT roove.
With the palm of your hand, tap the
DRAWER BOTTOM down into the roove.
Groove
Arrow
Maximum
210 derees
Minimum
190 derees
Start each screw a few turns before
completely tihtenin any of them.
BLACK 1-9/16" FLAT HEAD SCREW
(20 used in this step)
30S
K
K
K
VIEW THE T-LOCK BOX VIDEO
D31
D31
D733
D30
D30
D30
D31
D68
Unfinished
surface
M67
M67
Surface with
HIDDEN CAM

Step 13
417146 www.sauder.com/servicesPae 18
å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D30 and D31).
å Fasten a DRAWER RIGHT (35AC) to the DRAWER RIGHT SIDE (D30)
and a DRAWER LEFT (35AD) to the DRAWER LEFT SIDE (D31). Use
four GOLD 5/16" FLAT HEAD SCREWS (3S) throuh holes #1 and #2.
å NOTE: The parts are marked "DRAWER RIGHT" and "DRAWER LEFT"
for easy identification and the lides are not intended to rotate.
å NOTE: The screw head in the CAM must be visible throuh the
slotted hole in the SLIDE.
å Repeat this step for the remainin drawers.
1
2
1
2
Glide end
Glide end
Screw head - turn CAM to line up holes in
the SLIDES with holes in DRAWER SIDES
10A
10A
D31
D30
If you're doin this to
help a friend, don't
leave without a bite.
GOLD 5/16" FLAT HEAD SCREW
(16 used in this step)
3S
(4 screws per drawer)

å You have the option of fastenin a WOOD KNOB (60K) or a
CLEAR KNOB (107K) to the DRAWER FRONTS (K and L).
å Fasten the CLEAR KNOBS (107K) to the DRAWER
FRONT (K) with a SILVER 3/4" MACHINE SCREW (20S)
or fasten the WOOD KNOBS (60K) to the DRAWER
FRONT (K) with a BLACK 1-1/8" PAN HEAD SCREW (9S).
å Repeat this step for the remainin drawers.
Step 14
417146www.sauder.com/services Pae 19
SILVER 3/4" MACHINE SCREW
(8 used for the METAL KNOB)
20S
107K
K
(8 used)
(8 used)
60K
BLACK 1-1/8" PAN HEAD SCREW
(8 used in this step)
9S

Step 15
417146 www.sauder.com/servicesPae 20
å Position your unit in its final location. We recommend usin the SAFETY STRAP (60M) for added stability.
å NOTE: Do not turn the SAFETY DRYWALL ANCHOR (61M) into a wall stud. If you prefer to fasten the SAFETY
STRAP (60M) to a wall stud, o to your local hardware store for proper hardware.
å INSTALLATION INSTRUCTIONS: (Also available at www.yl-anchors.com)
1. Insert the SAFETY DRYWALL ANCHOR (61M) throuh the WASHER (13M) and one end of the SAFETY STRAP (60M).
2. Usin a Phillips screwdriver or a hand drill, press screw slihtly onto the drywall.
3. Apply pressure; turn the screw until a pilot hole is made and the nylon sheath slips throuh.
4. Turn the screw until it is flush aainst the wall and you feel a firm resistance.
5. Continue to turn until the screw starts spinnin freely.
å Carefully cut out the perforated hole in the BACK (F). Insert the other end of the SAFETY STRAP (60M) throuh this
hole, then use a BLACK 9/16" LARGE HEAD SCREW (1S) throuh the SAFETY STRAP and into the pre-drilled hole in the
underside of the TOP.
å NOTE: Before movin your unit to a dierent location, unscrew the SAFETY DRYWALL ANCHOR (61M) from your wall.
The nylon sheath will remain behind your wall.
60M
61M
BLACK 9/16" LARGE HEAD SCREW
(1 used in this step)
1S
13M
F