Sauder Via 419606 User manual

sauder.com
Lateral File
Via Collection | Model 419606
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-24
Français p 25-28
Español p 29-32
Lot # 531257 06/26/19
Purchased: __________________
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a rin at 1-800-523-3987.
Customer Service is available Monday-Friday - 8:30 a.m. to 5 p.m. EST (except holidays)
Sauder.com
Share your journey!
Get all organized
and stu.

Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Table of Contents Assembly Tools Required
3
4-5
6-24
25-28
29-32
33-34
35
419606 www.sauder.com/servicePae 2

åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Part Identification Now you know
our ABCs.
419606www.sauder.com/service Pae 3
A
B
C
D
E
F
G
H
B35
D205
D498
D499
M63
A RIGHT END (1)
B LEFT END (1)
B35 DRAWER BOTTOM (2)
C TOP (1)
D BOTTOM (1)
D205 LEFT DRAWER SIDE (2)
D498 RIGHT DRAWER SIDE (2)
D499 DRAWER BACK (2)
E SHELF (1)
F BACK (1)
G BASE (1)
H DRAWER FRONT (2)
M63
DRAWER BRACE (2)
(Hidden part usin recycled
material. Color may vary.)

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
419606 www.sauder.com/servicePae 4
34G INTERLOCK
MECHANISM - 1
DRAWER
ACTUATOR - 2
62G
FILE BAR - 4
1B
PROPEL NUT - 4
14M
METAL BRACKET - 5
4G
GROMMET CAP - 1
1P
7F TWIST-LOCK®FASTENER - 18
16E ADJUSTABLE
GLIDE - 4
PULL - 2
12K
CAM SCREW - 2
8F
CORD CLIP - 2
9P
LOCK
BRACKET - 2
5J LOCK
COVER - 2
10J
FILE BRACKET - 4
12B
HIDDEN CAM - 2
1F
LOCK - 2
16J
(EXTENSION SET SHOWN SEPARATED)
IEXTENSION RAIL - 4 JEXTENSION SLIDE - 4
FILE ROD - 4
18B FILE GLIDE - 4 19B 17E CASTER BRACKET - 4

åScrews are shown actual size. You may receive extra hardware with your unit.
Hardware Identification
419606www.sauder.com/service Pae 5
64P HALF GROMMET
CAP - 2 SUPPORT PIN - 4
5R
GROMMET - 1
10P HALF GROMMET - 2 67P
BLACK 9/16" PAN HEAD SCREW - 11
51S
BLACK 9/16" LARGE HEAD SCREW - 12
1S BROWN 7/16" LARGE HEAD SCREW - 16 6S
BLACK 7/8" MACHINE SCREW - 4
37S
BLACK 1/2" FLAT HEAD SCREW - 10
11S 30S BLACK 1-9/16" FLAT HEAD SCREW - 10

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å To bein assembly, push a SAUDER TWIST-LOCK®
FASTENER (7F) into the lare holes in the BACK (F).
å Repeat this step for the ENDS (A and B), BOTTOM (D),
and SHELF (E).
419606 www.sauder.com/servicePae 6
Do not tihten the TWIST-LOCK® FASTENERS in this step.
(18 used)
7F 7F
7F
F
Some assembly
(and snacks) required.
STOP
If you purchased
the 419708 Hutch,
assemble it first.
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code. 2

419606www.sauder.com/service Pae 7
Step 2
8F
å Turn two CAM SCREWS (8F) into the DRAWER FRONTS (H).
å Push two HIDDEN CAMS (1F) into the DRAWER BRACES (M63).
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
M63
M63
Arrow
1F
H
H
1

Step 3
419606 www.sauder.com/servicePae 8
å Separate the EXTENSION SLIDES (J) from the EXTENSION RAILS (I) as shown in the upper diaram below. Be prepared,
the parts are reasy.
å Fasten the EXTENSION RAILS (I) to the ENDS (A and B). Use eiht BLACK 9/16" PAN HEAD SCREWS (51S).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other hole that lines up with the hole in the END. Turn a SCREW into this
hole. You may need to apply some pressure on the SCREW with your Screwdriver to et it into the hole.
Push the black lever up and pull the SLIDE from the RAIL.
IJ
A
B
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
Open end
Open end
Use this hole.
NOTE: Be sure to use the
correct screw in this step.
BLACK 9/16" PAN HEAD SCREW
(8 used in this step)
51S
I
I
I
I
This small hole
must be here.
This small hole
must be here.
7

419606www.sauder.com/service Pae 9
Step 4
A
B
D
å Fasten the INTERLOCK MECHANISM (34G) to the RIGHT
END (A). Use three BLACK 9/16" PAN HEAD SCREWS (51S).
å With your hammer, ently tap four SUPPORT PINS (5R) into
the ENDS (A and B).
å Fasten five METAL BRACKETS (4G) to the
ENDS (A and B) and BOTTOM (D). Use five BLACK 9/16"
LARGE HEAD SCREWS (1S).
å NOTE: Be sure the BRACKETS are even with the edes of
the ENDS and BOTTOM. 34G
BLACK 9/16" PAN HEAD SCREW
(3 used in this step)
51S
4G
BLACK 9/16" LARGE HEAD SCREW
(5 used for the METAL BRACKETS)
1S
5R
4G
4G

Step 5
419606 www.sauder.com/servicePae 10
å Place a LEVELER BRACKET (17E) over the holes in the bottom
edes of the ENDS (A and B).
å Use a hammer to drive a PROPEL NUT (14M) throuh each
BRACKET and into the holes in the ENDS. Now, turn an
ADJUSTABLE GLIDE (16E) into each PROPEL NUT.
å NOTE: To raise a corner of the unit, turn the ADJUSTABLE
GLIDE counter-clockwise. To lower a corner, turn the
ADJUSTABLE GLIDE clockwise.
A
B
17E
16E
14M