Sauder Pogo 417675 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-18
Français p 19-21
Español p 22-24
Lot # 364664 09/26/14
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
3-Drawer Chest
Poo Collection | 417675
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.
Adult assembly required.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-18
19-21
22-24
25-26
27
417675 www.sauder.com/servicesPae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E BACK (1)
F FRONT PANEL (1)
G DRAWER FRONT (2)
H SMALL DRAWER FRONT (1)
I SKIRT (1)
J TOP MOLDING (1)
K RAIL (1)
L DRAWER BRACE (3)
D16 SMALL RIGHT DRAWER SIDE (1)
D17 SMALL LEFT DRAWER SIDE (1)
D22 RIGHT DRAWER SIDE (2)
D23 LEFT DRAWER SIDE (2)
D80 DRAWER BACK (2)
D178 SMALL DRAWER BACK (1)
D704 DRAWER BOTTOM (3)
417675www.sauder.com/services Pae 3
D704
D704
A
B
C
D
E
F
G
H
I
J
K
L
L
D16
D17
D178
D80 D22
D23

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
417675 www.sauder.com/servicesPae 4
5L WARNING LABEL - 1
(Refer to Step 13 for proper
location and application)
WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Place heaviest items in the lowest drawers.
• Unless specifically desined to accommodate, do not
set TVs or other heavy objects on top of this product.
• Never allow children to climb or han on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
• If equipped with a drawer interlock system, do not
defeat or remove it.
Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
This is a permanent label. Do not attempt to remove!
04/10 332296
CARD SHEET - 1
40M
35AA UNIVERSAL
CABINET RAIL - 6 35AC DRAWER RIGHT - 3 35AD DRAWER LEFT - 3
SAFETY STRAP - 1
Locate this nylon SAFETY
STRAP (60M) to be used
later in assembly. Do not
accidentally throw away.
60M
SAFETY DRYWALL
ANCHOR - 1
61M
WASHER - 1
13M
SILVER 3/4" MACHINE SCREW - 6
20S
GOLD 1" MACHINE SCREW - 6
50S
BROWN 7/16" LARGE HEAD SCREW - 11
6S BROWN 1-1/2" FLAT HEAD SCREW - 3 14S
3S GOLD 5/16" FLAT HEAD SCREW - 24
10A SLIDE CAM - 6
KNOB - 6
24K
WOOD DOWEL - 4
15F
NAIL - 36
1N
30S BLACK 1-9/16" FLAT HEAD SCREW - 15
HIDDEN CAM - 11
1F
CAM DOWEL - 11
2F
CARD HOLDER - 1
21M
SILVER 3/8" MACHINE SCREW - 2
97S
CLEAR
KNOB - 6
107K
METAL BRACKET - 5
4G

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push eleven HIDDEN CAMS (1F) into the ENDS (A and B),
BOTTOM (D), and DRAWER BRACES (L). Then, insert the
metal end of a CAM DOWEL (2F) into each HIDDEN CAM.
417675www.sauder.com/services Pae 5
Arrow
1F
2F
(11 used)
Arrow
1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tihten the HIDDEN CAMS in this step.
A
B
D
L
L
L

Step 2
417675 www.sauder.com/servicesPae 6
å Fasten the UNIVERSAL CABINET RAILS* (35AA) to the
ENDS (A and B). Use twelve GOLD 5/16" FLAT HEAD
SCREWS (3S) throuh holes #1 and #3.
å *patent pendin lide system
GOLD 5/16" FLAT HEAD SCREW
(12 used in this step)
3S
3
2
1
1
2
3
3
2
13
2
1
Glide end
1
2
31
2
3
Glide end
Remember:
Rihty tihty.
Lefty loosey.
A
B
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
Curved ede
Curved ede

å Fasten the RIGHT END (A) to the TOP (C). Tihten two
HIDDEN CAMS.
Step 3
417675www.sauder.com/services Pae 7
Start Tihten
Arrow
Minimum
190 derees
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Arrow
Maximum
210 derees
A
Surface with
HIDDEN CAMS
Curved ede
Surface with holes
C
Rounded ede
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution

å Fasten the BOTTOM (D) to the RIGHT END (A). Tihten
two HIDDEN CAMS.
Step 4
417675 www.sauder.com/servicesPae 8
Arrow
Minimum
190 derees
Maximum
210 derees
A
D
Surface with
HIDDEN CAMS
This hole must be here.

Step 5
417675www.sauder.com/services Pae 9
å Insert four WOOD DOWELS (15F) into the FRONT PANEL (F).
å Insert the WOOD DOWELS in the FRONT PANEL (F) into the
holes in the RIGHT END (A).
å Fasten the LEFT END (B) to the TOP (C) and BOTTOM (D).
Tihten four HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the FRONT PANEL (F)
insert into the holes in the LEFT END (B).
A
D
B
C
Curved ede
Surface without
HIDDEN CAMS
F
15F
15F
Arrow
Minimum
190 derees
Maximum
210 derees

å Fasten two METAL BRACKETS (4G) to the RAIL (K) as
shown in the upper diaram. Use two BROWN 7/16"
LARGE HEAD SCREWS (6S).
å NOTE: Be sure the BRACKETS are even with the ends of
the RAIL.
å Fasten the RAIL (K) to the ENDS (A and B) as shown in
the lower diaram. Use two BROWN 7/16" LARGE
HEAD SCREWS (6S).
å Fasten the TOP MOLDING (J) to the TOP (C). Use three
BROWN 1-1/2" FLAT HEAD SCREWS (14S).
Step 6
417675 www.sauder.com/servicesPae 10
4G
4G
Surface with
more holes
A
B
C
J
K
K
BROWN 7/16" LARGE HEAD SCREW
(4 used for the METAL BRACKETS)
6S
BROWN 1-1/2" FLAT HEAD SCREW
(3 used in this step)
14S
Curved ede

Step 7
417675www.sauder.com/services Pae 11
å Fasten three METAL BRACKETS (4G) to the ENDS (A and B)
and BOTTOM (D). Use three BROWN 7/16" LARGE
HEAD SCREWS (6S).
å NOTE: Be sure the BRACKETS are even with the edes of the
ENDS and BOTTOM.
å Fasten the SKIRT (I) to the ENDS (A and B) and BOTTOM (D).
Use three BROWN 7/16" LARGE HEAD SCREWS (6S) throuh
the BRACKETS and into the SKIRT.
Don't worry. It isn't
Rome. This can be built
in a day.
A
B
D
I
4G
4G
4G
Curved ede
BROWN 7/16" LARGE HEAD SCREW
(6 used in this step)
6S

Step 8
417675 www.sauder.com/servicesPae 12
Printed information
must be facin up.
å Carefully turn your unit over onto its front edes. Unfold
the BACK (E) and lay it over your unit.
å Make equal marins alon all four edes of the BACK (E).
Push on opposite corners of your unit if needed to make
it "square".
å Fasten the BACK (E) to your unit usin the NAILS (1N).
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution
NAIL
(36 used in this step)
1N
E
This hole
must be here.

Step 9
417675www.sauder.com/services Pae 13
å Insert the DRAWER SIDES (D22 and D23) at an angle
into the slot at each end of the DRAWER FRONT (G). å Slide the DRAWER BOTTOM (D704) into the
grooves in the DRAWER SIDES (D22 and D23) and
DRAWER FRONT (G).
å Fasten the DRAWER BRACE (L) to the DRAWER
FRONT (G). Tighten one HIDDEN CAM.
å Fasten the DRAWER BACK (D80) to the DRAWER SIDES (D22
and D23) and DRAWER BRACE (L). Use five BLACK 1-9/16"
FLAT HEAD SCREWS (30S).
å Repeat this step for the other DRAWERS. The small drawer will
use SMALL DRAWER FRONT (H), SMALL DRAWER SIDES (D16
and D17), and SMALL DRAWER BACK (D178).
The tabs should insert freely into the
slots. Gently tilt the DRAWER SIDES side
to side until the tabs slip into the slots.
Surface with
HIDDEN CAM
12
34
Be sure the DRAWER
BOTTOM inserts into the
DRAWER FRONT roove.
With the palm of your hand, tap the
DRAWER BOTTOM down into the roove.
Groove
Arrow
Maximum
210 derees
Minimum
190 derees
Start each screw a few turns before
completely tihtenin any of them.
BLACK 1-9/16" FLAT HEAD SCREW
(15 used in this step)
30S
G
L
G
VIEW THE T-LOCK BOX VIDEO
D23
D704
D22
D80
Unfinished
surface
G
D23
D22
L
D23
D22

Step 10
417675 www.sauder.com/servicesPae 14
å Insert a SLIDE CAM (10A) into the DRAWER SIDES (D22 and D23).
å Fasten a DRAWER RIGHT (35AC) to the DRAWER RIGHT SIDE (D22) and a DRAWER LEFT (35AD) to the DRAWER LEFT
SIDE (D23). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) throuh holes #1 and #2.
å NOTE: The parts are marked "DRAWER RIGHT" and "DRAWER LEFT" for easy identification.
å NOTE: The lides are not intended to rotate.
å NOTE: The screw head in the CAM must be visible throuh the slotted hole in the SLIDE.
å Repeat this step for the other drawers.
D23
D22
1
2
1
2
Screw head - turn CAM to line up holes in
the SLIDES with holes in DRAWER SIDES
10A
10A
Glide end
Glide end
GOLD 5/16" FLAT HEAD SCREW
(12 used in this step)
3S
(4 screws per drawer)

å NOTE: You have the option of fastenin the KNOBS (24K) or
the CLEAR KNOBS (107K) to your drawers. This step will show
fastenin the CLEAR KNOBS to the drawer. The KNOBS (24K)
will use the GOLD 1" MACHINE SCREWS (50S).
å Fasten the CLEAR KNOBS (107K) to the DRAWER FRONT (G).
Use two SILVER 3/4" MACHINE SCREWS (20S).
å Repeat this step for the other drawers.
Step 11
417675www.sauder.com/services Pae 15
G
107K
GOLD 1" MACHINE SCREW
(6 used for the KNOBS)
50S
SILVER 3/4" MACHINE SCREW
(6 used for the CLEAR KNOBS)
20S
If fastenin the KNOBS (24K) to
your drawers, use these SCREWS.
Almost time to
celebrate! With a nap.

Step 12
417675 www.sauder.com/servicesPae 16
60M
61M
13M
å Position your unit in its final location. We recommend usin the SAFETY STRAP (60M) for added stability.
å NOTE: Do not turn the SAFETY DRYWALL ANCHOR (61M) into a wall stud. If you prefer to fasten the SAFETY
STRAP (60M) to a wall stud, o to your local hardware store for proper hardware.
å INSTALLATION INSTRUCTIONS: (Also available at www.yl-anchors.com)
1. Insert the SAFETY DRYWALL ANCHOR (61M) throuh the WASHER (13M) and one end of the SAFETY STRAP (60M).
2. Usin a Phillips screwdriver or a hand drill, press screw slihtly onto the drywall.
3. Apply pressure; turn the screw until a pilot hole is made and the nylon sheath slips throuh.
4. Turn the screw until it is flush aainst the wall and you feel a firm resistance.
5. Continue to turn until the screw starts spinnin freely.
å Carefully cut out the perforated hole in the BACK (E). Insert the other end of the SAFETY STRAP (60M) throuh this hole,
then use a BROWN 7/16" LARGE HEAD SCREW (6S) throuh the SAFETY STRAP and into the pre-drilled hole in the
underside of the TOP.
å NOTE: Before movin your unit to a dierent location, unscrew the SAFETY DRYWALL ANCHOR (61M) from your wall.
The nylon sheath will remain behind your wall.
å Fasten the CARD HOLDER (21M) to the RAIL (K). Use two SILVER 3/8" MACHINE SCREWS (97S).
å Separate the CARDS on the CARD SHEET (40M) and insert one into the CARD HOLDER.
BROWN 7/16" LARGE HEAD SCREW
(1 used in this step)
6S
K
21M
40M
SILVER 3/8" MACHINE SCREW
(2 used in this step)
97S
E

Step 13
417675www.sauder.com/services Pae 17
å To insert the drawer into your unit, tip the front of the drawer down and drop the lides on the drawer behind the lides
on the unit. Lift the front of the drawer up and slide it into the unit.
å Apply the WARNING LABEL (5L) to the upper DRAWER BOTTOM (D704). You should be able to read the label when
the drawer is open. When the drawer is closed, it will hide the label. Peel o the backin and apply the label as shown
in the diaram.
å NOTE: This is a permanent label intended to last for the life of the product. Once applied, do not try to remove it.
G
H
D704
5L
Serious or fatal crushin injuries can
occur from furniture tip-over. To help
prevent tip-over:
-Place heaviest items in the lowest drawers.
-Unless specifically desined to accommodate,
do not set TVs or other heavy objects on top of
this product.
-Never allow children to climb or han on
drawers, doors, or shelves.
-Never open more than one drawer at a time.
-If equipped with a drawer interlock system, do not
defeat or remove it.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
WARNING
G
40 lbs.
20 lbs.
40 lbs.
30 lbs. each

Step 14
417675 www.sauder.com/servicesPae 18
å To make adjustments to the drawers, loosen SCREW #2 in the SLIDES a 1/4 turn, then turn the CAM clockwise or
counter-clockwise. Notice how the drawer raises or lowers as you turn the CAM. The hiher the screw in the oblon hole,
the hiher your drawer front will be. The lower the screw, the lower the drawer front. By adjustin the drawers this way, it
will help the DRAWER FRONTS line up better when closed. Tihten the SCREW when finished with adjustments.
å NOTE: Please read the back paes of the instruction booklet for important safety information.
å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.
And to celebrate, why not share your success story?
Cam
The hiher the screw in the oblon hole, the
hiher your drawer front will be. The lower
the screw, the lower the drawer front.
Loosen screw #2 a 1/4 turn, turn the cam a 1/4 turn
maximum in both the clockwise and counter-clockwise
directions to make adjustments, and then tihten screw #2.

A l’usae exclusif du
Canada Noter la date
d’achat de cet élément
et conserver le livret
pour future référence.
Pour contacter Sauder
en ce qui concerne cet
élément, faire référence
au numéro de lot et
numéro de modèle en
appelant notre numéro
sans frais.
Lot nº : ____________
Date de
l’achat: ____________
LISTE DE PIÈCES
REFERENCE DESCRIPTION QUANTITÉ
LISTE DE PIÈCES
REFERENCE DESCRIPTION QUANTITÉ
NOUS SOMMES LA POUR VOUS AIDER!
Nous faisons de notre mieux pour nous assurer que votre meuble
arrive dans d’excellentes conditions. Nos représentants du service
Clientèle sont aimables et prêts à vous aider au cas où une pièce
aurait été endommaée ou manquerait (ou si vous aviez besoin
d’aide pour l’assemblae). NE RAMENEZ PAS LE MEUBLE AU
MAGASIN. Au Canada, composez ce numéro d’appel ratuit:
1-800-523-3987
Du lundi au vendredi, de 9 heures du matin à
5:30 heures du soir (horaire Côte Est)
(sauf jours fériés)
Si une pièce a besoin d’être remplacée, la pièce de remplacement
sera envoyée dans les 48 heures. (Sauf week-ends et jours fériés)
Utilisez les instructions d’assemblae en français avec les
schémas étape par étape du manuel d’instruction en anlais.
Chaque étape en français correspond à la même étape
en anlais. La pièce devant être attachée à l’élément est
représentée en ris sur les schémas de chaque étape pour plus
de précision. Comparer la “Liste de pièces” ci-dessous avec
la “PART IDENTIFICATION” du manuel en anlais pour vous
familiariser avec les pièces avant l’assemblae.
REMARQUE : CE MANUEL D’INSTRUCTIONS CONTIENT
D’IMPORTANTES INFORMATIONS RELATIVES À LA SÉCURITÉ.
À LIRE ET CONSERVER POUR TOUTE RÉFÉRENCE FUTURE.
35AA GLISSIÈRE D'ÉLÉMENT UNIVERSELLE.....6
35AC TIROIR DROIT................................................................3
35AD TIROIR GAUCHE..........................................................3
10A EXCENTRIQUE DE COULISSE.........................6
1F EXCENTRIQUE ESCAMOTABLE....................11
2F CHEVILLE D'EXCENTRIQUE .............................11
15F CHEVILLE EN BOIS...................................................4
4G CONSOLE EN MÉTAL.............................................5
24K BOUTON............................................................................6
107K BOUTON TRANSPARENT....................................6
5L ÉTIQUETTE DE MISE EN GARDE....................1
(Consulter l'étape 13 pour l'emplacement
et application appropriées)
13M RONDELLE........................................................................1
21M PORTE-CARTES...........................................................1
40M FEUILLE DE CARTES................................................1
60M SANGLE DE SÉCURITÉ...........................................1
Localiser cette SANGLE DE SÉCURITÉ (60M)
à utiliser ultérieurement dans l’assemblae.
Ne pas la jeter accidentellement.
61M DISPOSITIF DE SÉCURITÉ POUR
PLACOPLÂTRE..............................................................1
1N CLOU ................................................................................36
3S VIS TÊTE PLATE 8 mm DORÉE...................24
6S VIS TÊTE LARGE 11 mm MARRON.............11
14S VIS TÊTE PLATE 38 mm MARRON .............3
20S VIS À MÉTAUX 19 mm ARGENTÉE..............6
30S VIS TÊTE PLATE 40 mm NOIRE ................. 15
50S VIS À MÉTAUX 25 mm DORÉE.......................6
97S VIS À MÉTAUX 9,5 mm ARGENTÉE............2
A EXTRÉMITÉ DROITE..................................................1
B EXTRÉMITÉ GAUCHE...............................................1
C DESSUS...............................................................................1
D DESSOUS...........................................................................1
E ARRIÈRE ..............................................................................1
F PANNEAU AVANT........................................................1
G DEVANT DE TIROIR...................................................2
H DEVANT DE PETIT TIROIR ...................................1
I PLINTHE..............................................................................1
J MOULURE SUPÉRIEURE........................................1
K TRAVERSE .........................................................................1
L ENTRETOISE DE TIROIR.......................................3
D16 CÔTÉ DROIT DE PETIT TIROIR........................1
D17 CÔTÉ GAUCHE DE PETIT TIROIR..................1
D22 CÔTÉ DROIT DE TIROIR.......................................2
D23 CÔTÉ GAUCHE DE TIROIR.................................2
D80 ARRIÈRE DE TIROIR..................................................2
D178 ARRIÈRE DE PETIT TIROIR...................................1
D704 FOND DE TIROIR.........................................................3
Commode 3 Tiroirs417675
417675www.sauder.com/services Pae 19

ÉTAPE 9
1 Insérer les CÔTÉS DE TIROIR (D22 et D23) en biseau dans la
fente dans chaque extrémité du DEVANT DE TIROIR (G).
2 Enfiler le FOND DE TIROIR (D704) dans les rainures des
CÔTÉS DE TIROIR (D22 et D23) et du DEVANT DE TIROIR (G).
3 Fixer l’ENTRETOISE DE TIROIR (L) au DEVANT DE TIROIR (G).
Serrer un EXCENTRIQUE ESCAMOTABLE.
4 Fixer l'ARRIÈRE DE TIROIR (D80) aux CÔTÉS DE TIROIR (D22
et D23) et à l’ENTRETOISE DE TIROIR (L). Utiliser cinq VIS TÊTE
PLATE 40 mm NOIRES (30S). (30S).
Répéter cette étape pour les autres TIROIRS. Le petit tiroir utilisera
le DEVANT DE PETIT TIROIR (H), les CÔTÉS DE PETIT TIROIR (D16
et D17) et l'ARRIÈRE DE PETIT TIROIR (D178).
ÉTAPE 8
Attention: Ne pas relever l'élément dans sa position verticale
avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'eondrer.
Avec précaution, retourner l'élément sur ses chants avant. Déplier
l'ARRIÈRE (E) et le placer sur l'élément.
Veiller à avoir des mares éales le lon des quatre chants de
l'ARRIÈRE (E). Si besoin est, enfoncer sur les coins opposés de
l'élément pour s'assurer d'être « d'équerre ».
Fixer l'ARRIÈRE (E) à l'élément à l'aide des CLOUS (1N).
ÉTAPE 7
Fixer trois CONSOLES EN MÉTAL (4G) aux EXTRÉMITÉS (A et B) et au
DESSOUS (D). Utiliser trois VIS TÊTE LARGE 11 mm MARRON (6S).
REMARQUE : S'assurer que les CONSOLES sont à fleur des
chants des EXTRÉMITÉS et du DESSOUS.
Fixer la PLINTHE (I) aux EXTRÉMITÉS (A et B) et au DESSOUS (D).
Utiliser trois VIS TÊTE LARGE 11 mm MARRON (6S) à travers les
CONSOLES et dans la PLINTHE.
ÉTAPE 6
Fixer deux CONSOLES EN MÉTAL (4G) à la TRAVERSE (K)
comme l'indique le schéma du haut. Utiliser deux VIS TÊTE
LARGE 11 mm MARRON (6S).
REMARQUE : S'assurer que les CONSOLES sont à fleur des
extrémités de la TRAVERSE.
Fixer la TRAVERSE (K) sur les EXTRÉMITÉS (A et B) comme l’indique le
schéma inférieur. Utiliser deux VIS TÊTE LARGE 11 mm MARRON (6S).
Fixer la MOULURE DE DESSUS (J) au DESSUS (C). Utiliser trois
VIS TÊTE PLATE 38 mm MARRON (14S).
ÉTAPE 5
Insérer quatre CHEVILLES EN BOIS (15F) dans le PANNEAU
AVANT (F).
Insérer les CHEVILLES EN BOIS du PANNEAU AVANT (F) dans
les trous de l’EXTRÉMITÉ DROITE (A).
Fixer l'EXTRÉMITÉ GAUCHE (B) au DESSUS (C) et au DESSOUS (D).
Serrer quatre EXCENTRIQUES ESCAMOTABLES.
REMARQUE : S'assurer de bien insérer les CHEVILLES EN BOIS du
PANNEAU AVANT (F) dans les trous de l'EXTRÉMITÉ GAUCHE (B).
ÉTAPE 4
Fixer le DESSOUS (D) à l'EXTRÉMITÉ DROITE (A). Serrer deux
EXCENTRIQUES ESCAMOTABLES.
ÉTAPE 3
Attention: Ne pas relever l'élément dans sa position verticale
avant d'avoir fixé l’ARRIÈRE. L'élément risque de s'eondrer.
Fixer l'EXTRÉMITÉ DROITE (A) au DESSUS (C). Serrer deux
EXCENTRIQUES ESCAMOTABLES.
Attention: Risque des déâts ou blessures. Les Excentriques
Escamotables doivent être serrés à bloc. Les Excentriques
Escamotables que ne sont pas serrées à bloc peuvent desserrer
et les pièces peuvent séparer. Pour serrer à bloc, faire tourner
l'excentrique escamotable de 210 derés.
ÉTAPE 2
Fixer les GLISSIÈRES D'ÉLÉMENT UNIVERSELLES* (35AA) aux
EXTRÉMITÉS (A et B). Utiliser douze VIS TÊTE PLATE 8 mm
DORÉES (3S) à travers les trous nº 1 et nº 3.
*système de coulisse en instance de brevet
ÉTAPE 1
Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans cette étape.
Assembler l'élément sur un sol à moquette ou sur le carton vide
pour éviter d'endommaer l'élément ou le sol.
Enfoncer onze EXCENTRIQUES ESCAMOTABLES (1F) dans les
EXTRÉMITÉS (A et B), le DESSOUS (D) et les ENTRETOISES DE
TIROIR (L). Ensuite, insérer l'extrémité en métal de la CHEVILLE
D'EXCENTRIQUE (2F) dans chaque EXCENTRIQUE ESCAMOTABLE.
417675 www.sauder.com/servicesPae 20