Sauder Credenza 420723 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-32
Français pg 33-36
Español pg 37-40
Lot # 393586 08/17/16
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Credenza
Harbor View Collection | Model 420723
Designed for
distractions.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
95 lbs.
95 lbs.
19-1/8"
19-1/8"
71-1/4"
71-1/4"
WARNING
!
Use of a TV that is too heavy or large is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too large for the available space might be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly!
• This Sauder unit is designed for use with televisions weighing less than 95 pounds. Never use with a TV that weighs more.
• The size of the television, front-to-back and side-to-side, must fit within the space defined in the diagram.
• Never place the front edge of the TV past the front edge of the TV support shelf (or stop molding – if equipped)
• Never allow the sides of the TV to extend past the side edges of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warning label as instructed in the last assembly step. The label provides important safety related information.
3-4
5-6
7-32
33-36
37-40
41-42
43
420723 www.sauder.com/servicesPage 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
E2 TOP (1)
F BOTTOM (1)
G RIGHT BACK (1)
H LEFT BACK (1)
I CENTER BACK (2)
O ADJUSTABLE SHELF (1)
P SMALL ADJUSTABLE SHELF (2)
Q BASE (1)
X FRONT MOLDING (1)
Y RIGHT MOLDING (1)
Z LEFT MOLDING (1)
AA MOLDING (1)
BB BOTTOM MOLDING (1)
CC CENTER SUPPORT (4)
DD SHELF MOLDING (1)
EE PLINTH (2)
420723www.sauder.com/services Page 3
A
B
C
D
E2
F
G
HI
I
O
P
Q
X
Z
AA
BB
DD
EE
Y
P
CC
EE

Part Identification
J RIGHT DOOR (1)
K LEFT DOOR (1)
L INNER RIGHT DOOR (1)
M INNER LEFT DOOR (1)
N GLASS DOOR (2)
R RIGHT DRAWER FRONT (1)
S LEFT DRAWER FRONT (1)
T CENTER DRAWER FRONT (1)
U DRAWER BACK (1)
V DRAWER SIDE (2)
W DRAWER BOTTOM (1)
D24 SMALL RIGHT DRAWER SIDE (2)
D25 SMALL LEFT DRAWER SIDE (2)
D154 SMALL DRAWER BACK (2)
D960 SMALL DRAWER BOTTOM (2)
420723 www.sauder.com/servicesPage 4
D960
D154
D960
D154
J
K
L
M
N
R
S
T
U
V
W
N
V
D24
D25
D25
D24

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
420723www.sauder.com/services Page 5
40CA CABINET RIGHT - 2
(EXTENSION SET SHOWN SEPARATED)
FF EXTENSION RAIL - 2 GG EXTENSION SLIDE - 2
40CB CABINET LEFT - 2 40CC DRAWER RIGHT - 2 40CD DRAWER LEFT - 2 SLIDE CAM - 4 10A
5E CORNER
CAP - 2 6E FOOT BRACKET - 2
40H CURVED
HINGE - 4
13H HINGE - 4
HIDDEN CAM - 16
1F CAM DOWEL - 16 2F
MOLDING CONNECTOR - 2
16F
LARGE RUBBER SLEEVE - 1
58G
TIE PLATE - 1
3G
LARGE METAL
BRACKET - 3
1G
ANGLE
BRACKET - 3
27G
METAL BRACKET - 6
4G

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
420723 www.sauder.com/servicesPage 6
BLACK 1-7/8" FLAT HEAD SCREW - 21
2S
BLACK 9/16" LARGE HEAD SCREW - 30
1S
BLACK 1/2" FLAT HEAD SCREW - 16
11S
SILVER 1-1/4" MACHINE SCREW - 4
35S
SILVER 5/8" MACHINE SCREW - 6
15S
SILVER 2" FLAT HEAD SCREW - 10
57S
GOLD 5/16" FLAT HEAD SCREW - 24
3S BLACK 1-1/8" PAN HEAD SCREW - 11 9S
WARNING LABEL - 1
3L
(Refer to step 25 for proper
location and application)
PULL - 3
98K
METAL PIN - 20
1R RUBBER SLEEVE - 12 2R10P GROMMET - 5
DOOR STOP - 2
4I
CAM COVER - 2
12P
KNOB SET - 4
99K
BLACK 1-9/16" FLAT HEAD SCREW - 8
30S

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push sixteen HIDDEN CAMS (1F) into the ENDS (A and B),
UPRIGHTS (C and D), BOTTOM (F), DRAWER SIDES (V)
and DRAWER BOTTOM (W). Then, insert the metal end
of a CAM DOWEL (2F) into each HIDDEN CAM.
420723www.sauder.com/services Page 7
A
B
C
D
F
W
V
V
(16 used)
Arrow
1F
2F
Do not tighten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow

å Separate the EXTENSION SLIDES (GG) from the
EXTENSION RAILS (FF) as shown in the diagram below.
Be prepared, the parts are greasy.
å Fasten the EXTENSION RAILS (FF) to the UPRIGHTS (C
and D). Use four GOLD 5/16" FLAT HEAD SCREWS (3S).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the
hole shown in the enlarged diagram. Then, slide the inner
cartridge of the EXTENSION RAIL in to find the other hole
that lines up with the hole in the UPRIGHT. Turn a SCREW
into this hole.
Step 2
420723 www.sauder.com/servicesPage 8
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
C
D
FFGG
FF
FF
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
Notched edge
Notched edge
Open end
Open end
Push the release lever in and pull the SLIDE from the RAIL.
Remember:
Righty tighty.
Lefty loosey.

å Fasten the CABINET RIGHTS (40CA) and CABINET LEFTS (40CB) to the ENDS (A and B) and other surface of the
UPRIGHTS (C and D). Use eight GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3.
Step 3
420723www.sauder.com/services Page 9
1
2
34
C
D
B
A
Surface with
HIDDEN CAMS Surface with
HIDDEN CAMS
Surface without
HIDDEN CAMS Surface without
HIDDEN CAMS
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
3S
Roller end
Roller end
Roller end
Roller end
Notched edge
Notched edge
Edge with
HIDDEN CAMS
1
2
3
4
1
2
34
1
2
3
4

å Tap two MOLDING CONNECTORS (16F) into the notches
in the MOLDINGS (X, Y, and Z).
Step 4
420723 www.sauder.com/servicesPage 10
16F
16F
XY
Z
Flat end
Flat end
Use your hammer to tap the MOLDING CONNECTORS (16F) into the notches in the MOLDINGS.