Sauder Shoal Creek 422191 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
For all your
newfanled gadgetry.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-28
Français p 29-32
Español p 33-36
Lot # 510498 11/07/17
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
L-Desk
Shoal Creek Collection | Model 422191

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-28
29-32
33-36
37-38
39
422191 www.sauder.com/servicesPae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C RIGHT TOP (1)
D LEFT TOP (1)
D14 RIGHT DRAWER SIDE (1)
D15 LEFT DRAWER SIDE (1)
D78 DRAWER BACK (1)
D716 DRAWER BOTTOM (1)
E RIGHT UPRIGHT (1)
F RIGHT SUPPORT (1)
G LEFT SUPPORT (1)
H RIGHT MODESTY PANEL (1)
I LEFT MODESTY PANEL (1)
J BOTTOM (1)
K RIGHT END MOLDING (2)
L LEFT END MOLDING (1)
M SHELF (1)
N PURSE SHELF (1)
O DRAWER FRONT (1)
P INNER DRAWER FRONT (1)
QRIGHT FRONT/LEFT
REAR LEG (3)
RLEFT FRONT/RIGHT
REAR LEG (3)
S BACK (1)
A
B
C
D
E
F
GH
I
J
K
K
L
M
N
O
P
Q
Q
Q
R
R
R
S
D14
D15 D78
D716
422191www.sauder.com/services Pae 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 9/16" LARGE HEAD SCREW - 16
1S
GRAY 1-3/8" MACHINE SCREW - 4
39S
GROMMET CAP - 2
1P
CAM COVER - 8
12P
7F TWIST-LOCK®FASTENER - 28
SCREW COVER - 7
20P
3S GOLD 5/16" FLAT HEAD SCREW - 8
PULL - 2
7K
BLACK 9/16" FLAT HEAD SCREW - 6
32S
CAM SCREW - 18
8F
WOOD DOWEL - 6
15F
GROMMET - 2
10P
HIDDEN CAM - 18
1F
SILVER 1" LARGE HEAD SCREW - 2
102S
BLACK 1-15/16" FLAT HEAD SCREW - 13
113S
30S BLACK 1-9/16" FLAT HEAD SCREW - 4
FILE GLIDE - 2
4B
422191 www.sauder.com/servicesPae 4
PLATE - 4
41G
(EXTENSION SET SHOWN SEPARATED)
EXTENSION RAIL - 2
35MA EXTENSION SLIDE - 2 35MC

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
(28 used)
7F
Do not tihten the TWIST-LOCK® FASTENERS in this step.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å To bein assembly, push twenty-eiht SAUDER
TWIST-LOCK® FASTENERS (7F) into the lare holes in the
ENDS (A and B), RIGHT UPRIGHT (E), SUPPORTS (G and F),
MODESTY PANELS (H and I), SHELF (M), PURSE SHELF (N),
and BACK (S).
7F
7F
7F
7F
N
422191www.sauder.com/services Pae 5
S
M
I
H
G
F
A
B
E

Step 2
8F
å Turn eihteen CAM SCREWS (8F) into the LEGS (Q and R).
R
R
R
Q
Q
Q
422191 www.sauder.com/servicesPae 6

Step 3
Arrow
1F
Arrow
The arrow in the HIDDEN
CAM must point toward the
hole in the ede of the board.
Hole
å Push eihteen HIDDEN CAMS (1F) into the ENDS (A and B)
and UPRIGHT (E).
(18 used)
1F
Arrow
E
A
B
422191www.sauder.com/services Pae 7

Step 4
å Turn two BLACK 9/16" FLAT HEAD SCREWS (32S) into
the LEFT END (B) until the shoulders of the SCREWS rest
on the surfaces of the END.
å NOTE: Do not overtihten the SCREWS.
å Slide the LEFT END MOLDING (L) onto the LEFT END (B).
Line up the rooves in the MOLDINGS over the heads of
the SCREWS in the END.
å NOTE: The MOLDINGS should be even on both edes of
the END.
å NOTE: If the MOLDING comes up o of the SCREWS,
remove it and slide it on aain.
BLACK 9/16" FLAT HEAD SCREW
(2 used in this step)
32S
Surface without
TWIST-LOCK®
FASTENERS
Shoulder
Apply pressure with your hands
as you uide the MOLDINGS over
the SCREWS and onto the ENDS.
B
L
422191 www.sauder.com/servicesPae 8
Just think. The sooner
you do this, the sooner
you do somethin else.

Step 5
1
2
These surfaces
should be even.
15F
15F
å Insert two WOOD DOWELS (15F) into the LEGS (Q and R).
å Fasten the LEFT END (B) to the LEGS (Q and R). Tihten
six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS insert into the END.
Q
R
B
Anled ede
Anled ede Ede with
TWIST-LOCK®
FASTENERS
422191www.sauder.com/services Pae 9
Surface with HIDDEN CAMS

Step 6
å Separate the EXTENSION SLIDES (35MC) from the EXTENSION RAILS (35MA) as shown in the enlared diaram below. Be
prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (35MA) to the RIGHT END (A) and RIGHT UPRIGHT (E). Use four GOLD 5/16" FLAT
HEAD SCREWS (3S).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlared diaram. Then, slide the inner
cartride of the EXTENSION RAIL in to find the other hole that lines up with the hole in the END. Turn a SCREW into this
hole.
å NOTE: The EXTENSION SLIDES (35MC) will be used later for the DRAWER.
Open end
Open end
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
A
E
422191 www.sauder.com/servicesPae 10
Push the black lever in and pull the SLIDE from the RAIL.
35MA
35MC

å Insert a WOOD DOWEL (15F) into each of the LEGS (Q and R).
å Fasten the RIGHT END (A) to the LEFT FRONT/RIGHT
REAR LEG (R) as shown to the riht. Tihten three
HIDDEN CAMS.
å Fasten the RIGHT UPRIGHT (E) to the RIGHT FRONT/
LEFT REAR LEG (Q) as shown below. Tihten three
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWEL inserts into the END
and UPRIGHT.
Step 7
422191www.sauder.com/services Pae 11
Q
A
R
E
15F
15F
These surfaces
should be even.
These surfaces
should be even.
Ede with TWIST-LOCK®
FASTENERS
Ede with TWIST-LOCK®
FASTENERS
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
1
2

å Lay the RIGHT END (A) on the floor as shown.
å Fasten the SHELF (M) and BACK (S) to the RIGHT END (A).
Tihten four TWIST-LOCK® FASTENERS.
Step 8
422191 www.sauder.com/servicesPae 12
How to use the SAUDER TWIST-LOCK® FASTENER
1. Insert the dowel end of the FASTENER into the
hole of the adjoinin part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoinin
part while lockin the FASTENER.
2. Tihten the FASTENER with a Phillips
screwdriver as tiht as possible.
Dowel end
A
M
S
R
Anled ede
Surface with TWIST-LOCK® FASTENERS
Surface with TWIST-LOCK® FASTENERS

å Fasten the RIGHT UPRIGHT (E) to the SHELF (M) and
BACK (S). Tihten four TWIST-LOCK® FASTENERS.
Step 9
422191www.sauder.com/services Pae 13
M
S
E
Q
Anled ede

å Turn your assembly onto the REAR LEGS (Q and R).
å Fasten the BOTTOM (J) to the RIGHT END (A) and
RIGHT UPRIGHT (E). Use four BLACK 1-15/16" FLAT
HEAD SCREWS (113S).
Step 10
422191 www.sauder.com/servicesPae 14
R
Q
J
BLACK 1-15/16" FLAT HEAD SCREW
(4 used in this step)
113S
113S
A
E
S
openin

Step 11
422191www.sauder.com/services Pae 15
A
E
å Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into the RIGHT END (A) and RIGHT UPRIGHT (E) until the shoulders
of the SCREWS rest on the surfaces of the END.
å NOTE: Do not overtihten the SCREWS.
å Slide the RIGHT END MOLDINGS (K) onto the RIGHT END (A) and RIGHT UPRIGHT (E). Line up the rooves in the
MOLDINGS over the heads of the SCREWS in the END and UPRIGHT.
å NOTE: The MOLDINGS should be even with the top edes of the END and UPRIGHT.
å NOTE: If the MOLDING comes up o of the SCREWS, remove it and slide it on aain.
BLACK 9/16" FLAT HEAD SCREW
(4 used in this step)
32S
K
K
Apply pressure toward the END with
your hands as you uide the MOLDING
over the SCREWS and onto the END.
Apply pressure toward the UPRIGHT with
your hands as you uide the MOLDINGS
over the SCREWS and onto the UPRIGHT.
Shoulder
The roove should be aainst
the END and UPRIGHT.
Shoulder

å Insert two WOOD DOWELS (15F) into the LEGS (Q and R).
å Fasten the RIGHT FRONT/LEFT REAR LEG (Q) to the
RIGHT END (A) and the LEFT FRONT/RIGHT REAR LEG (R)
to the RIGHT UPRIGHT (E). Tihten six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the LEGS insert
into the holes in the END and UPRIGHT.
Step 12
422191 www.sauder.com/servicesPae 16
A
E
Q
R
15F

å Fasten the RIGHT END (A) and RIGHT UPRIGHT (E) to the
RIGHT TOP (C).
Tihten four TWIST-LOCK® FASTENERS.
Step 13
422191www.sauder.com/services Pae 17
A
E
C
Surface with holes
This lare hole
must be here.
S
Openin

Step 14
422191 www.sauder.com/servicesPae 18
å Fasten the RIGHT MODESTY PANEL (H) to the RIGHT
TOP (C).
Tihten two TWIST-LOCK® FASTENERS.
å Fasten the RIGHT MODESTY PANEL (H) to the RIGHT
UPRIGHT (E). Use two BLACK 1-15/16" FLAT HEAD
SCREWS (113S).
C
H
Now miht be a
ood time to refresh
your drink.
BLACK 1-15/16" FLAT HEAD SCREW
(2 used in this step)
113S
E

å Fasten the SUPPORTS (F and G) to the RIGHT TOP (C).
Tihten two TWIST-LOCK® FASTENERS
å Fasten the LEFT SUPPORT (G) to the RIGHT SUPPORT (F).
Use three BLACK 1-15/16" FLAT HEAD SCREWS (113S).
å Fasten the RIGHT SUPPORT (F) to the RIGHT
MODESTY PANEL (H). Use two BLACK 1-15/16" FLAT
HEAD SCREWS (113S).
Step 15
422191www.sauder.com/services Pae 19
C
BLACK 1-15/16" FLAT HEAD SCREW
(5 used in this step)
113S
G
F
H

å Fasten four PLATES (41G) to the RIGHT TOP (C) Use
eiht BLACK 9/16" LARGE HEAD SCREWS (1S).
Step 16
422191 www.sauder.com/servicesPae 20
41G
C
BLACK 9/16" LARGE HEAD SCREW
(8 used in this step)
1S