Sauder 415547 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
English.................... Page 1-14
Français...............Pages 15-16
Espanol.............Páginas 17-18
Lot #: 353689 08 / 16 / 13
Date Purchased: ____________________
415547
Twin Bookcase Headboard

ADULT ASSEMBLY REQUIRED
ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-14
Français..............................15-16
Espanol...............................17-18
Warranty...................................19
Page 2 www.sauder.com/services 415547
Electric drill with 1/4" bit
(ONLY in indicated step)

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A RIGHT END 1
B LEFT END 1
C UPRIGHT 1
D TOP 1
E SHELF 1
F BACK 1
G PANEL 2
H ADJUSTABLE SHELF 2
Page 3
www.sauder.com/services415547
A
B
C
D
E
F
G
H
H
G

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/services 415547
HEADBOARD BRACKET - 2
16G
HIDDEN CAM - 18
1F CAM DOWEL - 18 2F
NAIL - 35
1N METAL PIN - 8 1R RUBBER SLEEVE - 8 2R
BLACK 9/16" LARGE HEAD SCREW - 16
1S BLACK 1-7/8" FLAT HEAD SCREW - 2 2S
ANGLE BRACKET - 2
27G
SILVER 2" BOLT - 4
94S
WASHER - 4
13M NUT - 4
24M
CAM COVER - 6
19P
TIE PLATE - 2
3G
BLACK 1-1/8" PAN HEAD SCREW - 2
9S
SILVER 1" LARGE HEAD SCREW - 2
102S

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push eighteen HIDDEN CAMS (1F) into the UPRIGHT (C), TOP (D), SHELF (E), and both PANELS (G). Then, insert the metal end
of a CAM DOWEL (2F) into each HIDDEN CAM.
Page 5
www.sauder.com/services415547
Do not tighten the HIDDEN CAMS in this step.
Arrow
(18 used) 1F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
C
D
E
G
G

Fasten the SHELF (E) to the RIGHT END (A). Tighten two HIDDEN CAMS.
2
2
S
t
e
p
Page 6 www.sauder.com/services 415547
Caution
Risk of damage or
injury. Hidden Cams
must be completely
tightened. Hidden
Cams that are not
completely tightened
may loosen, and parts
may separate.
To completely tighten:
Start Tighten
Arrow
Arrow
Maximum
210 degrees
Minimum
190 degrees
A
E
Surface
with
holes
Surface with
HIDDEN
CAMS
Finished edge
Curved edge

Surface
with
HIDDEN
CAMS
3
3
S
t
e
p
Page 7
www.sauder.com/services415547
Fasten the UPRIGHT (C) to the SHELF (E). Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S).
Fasten the TOP (D) to the RIGHT END (A) and UPRIGHT (C). Tighten four HIDDEN CAMS.
Maximum
210 degrees
Minimum
190 degrees
Arrow
A
E
C
D
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
2S
Finished edge
Surface with
HIDDEN CAMS

Fasten two ANGLE BRACKETS (27G) to one of the PANELS (G). Use two BLACK 9/16" LARGE HEAD SCREWS (1S).
NOTE: Be sure the edges of the ANGLE BRACKETS are even with the edge of the PANEL.
Fasten the PANEL (G) to the RIGHT END (A). Tighten two HIDDEN CAMS.
Fasten the PANEL (G) to the SHELF (E). Use two BLACK 9/16" LARGE HEAD SCREWS (1S) through the ANGLE BRACKETS
on the PANEL and into the SHELF.
4
4
S
t
e
p
Page 8 www.sauder.com/services 415547
G
27G
Surface with
HIDDEN CAMS
Maximum
210 degrees
Minimum
190 degrees
Arrow
G
E
A
Surface with
HIDDEN
CAMS
BLACK 9/16" LARGE HEAD SCREW
(4 used for the BRACKETS)
1S
These holes
must be here.

5
5
S
t
e
p
Page 9
www.sauder.com/services415547
G
A
G
Fasten the remaining PANEL (G) to the RIGHT END (A). Tighten two HIDDEN CAMS.
Fasten the PANEL (G) to the other PANEL (G). Use two TIE PLATES (3G) and four BLACK 9/16" LARGE HEAD SCREWS (1S).
Maximum
210 degrees
Minimum
190 degrees
Arrow
Surface with
HIDDEN
CAMS
3G
BLACK 9/16" LARGE HEAD SCREW
(4 used in this step)
1S
These holes
must be here.

6
6
S
t
e
p
Page 10 www.sauder.com/services 415547
Fasten the LEFT END (B) to the TOP (D), SHELF (E), and both PANELS (G). Tighten eight HIDDEN CAMS.
Maximum
210 degrees
Minimum
190 degrees
Arrow
G
G
E
D
B
Surface
without
holes
Curved edge